May i use flashing cement to stick it on the roof ?
@quijasfrankАй бұрын
Way wrong
@diegoquinonez62822 ай бұрын
U don't really need bonding adhesive. I don't think it works on pvc
@rps7143 ай бұрын
what about when there is not enough room for 2 inches extra coverage. for example the edge of the roof 90* drop off. My TPO roof has cracked at the roof's side edges and made some small 1" slices where its appears the plywood edge pushes up into it from below.
@chrobist3 ай бұрын
what are some common products that can be used for cleaning prep and cut edge sealing? Iso alcohol and silicone respectively?
@jakecarlan8061Ай бұрын
Weathered membrane cleaner for the prep. Whichever brand TPO you're using will typically sell it. Same for the edge sealing, there is a specific product they call "cut edge sealant" that you need to use. Wherever you bought the TPO from should sell both.
@joecox99585 ай бұрын
good, rush, not easy to understand, too dry.
@MJamMan7 ай бұрын
I have a roof in CT that looks flat to the eye and is a black 10 ft seams wide material covered with a layer of pea sized rocks. It is completely drained after a rain in about 2 hours, and completely dry after 4-6 hours. What peel and stick product will work on this? Most contractors that have looked at the roof have no clue. I want to strip it down, replace any bad plywood than use a peel and stick application only, (no fumes allowed). Any advice from anyone is much appreciated. Thanks
@arthurbeugnies35218 ай бұрын
Is there a limit in time to repair a pvc roof. I’ve been told that after 10 years it couldn’t be repaired anymore and the whole roof has to been renewed. Thanks.
@MuleHideVideos8 ай бұрын
Single-Ply roofs can typically be repaired throughout the life of the roofing system. Since Mule-Hide offers warranties up to 30-years in duration there should not be an issue with making repairs to the system. Proper cleaning and preparation will be critical to the success of the repairs.
@woahlookatthetime10 ай бұрын
This video is super weld done 😉
@psonparote10 ай бұрын
Where can I buy this EPDM boot? Thanks
@MuleHideVideos10 ай бұрын
Please reach out to your local Mule-Hide rep (linked below). They will be able to help you! www.mulehide.com/Contact-Us/Find-a-Rep-Dist
@alexandromartinez7035 Жыл бұрын
🎉🎉🎉🎉🎉 ❤❤❤❤ love 💕
@eddiegomez3628 Жыл бұрын
Add links to where to buy this stuff. Im going to try home depot.
@MuleHideVideos10 ай бұрын
Hello, please reach out to your local Mule-Hide rep. www.mulehide.com/Contact-Us/Find-a-Rep-Dist
@eddiegomez362810 ай бұрын
@@MuleHideVideos Thank you. I know where to start at least.
@nestorsanchez322628 күн бұрын
Can I use flashing cement to stick it on the roof ??
@AlloyedFrequencies Жыл бұрын
Thank you so much sir
@advancedue476 Жыл бұрын
The old hand shredder plates
@user-ue1fe7gi6z Жыл бұрын
This is upholstery for curb 😂😂😂
@ignitedelmarva8075 Жыл бұрын
@mulehide I need a rep to contact me
@memeet2511 Жыл бұрын
Gracias mañana lo intentaremos 🙏🙏🙏👌👌
@jeremiahhall2577 Жыл бұрын
Thank you
@uy-scutipacific6398 Жыл бұрын
Where to buy it
@douglasemerson9017 Жыл бұрын
ABC Supply.
@skywalkk0079 Жыл бұрын
Thinking on using on roof top of my Rv
@MattWhite-pg2ro Жыл бұрын
same here.
@memeet2511 Жыл бұрын
Excelente explicación
@MackTheRoofer Жыл бұрын
When I do this, I put the seam tape on the flashing, then glue the flashing up to the tape. That way you don't need to trim at the bottom since the tape is already there with the proper exposure...
@calebhelmuth Жыл бұрын
Loves this product. Always have some with me for temporary repairs.
@MrUsaer Жыл бұрын
Will this SA BaseSheet be hard to remove from plywood deck in 10 years? How do u remove it? Should it be put over the nail base first for easier removal later?
@fun1492 ай бұрын
I have the same question
@davidborntreger691 Жыл бұрын
Love this
@krisdixon2402 Жыл бұрын
I’ve used Mule Hide for over twenty years. The silicone makes a nice looking roof that last. ABC Tampa
@BigVic13 Жыл бұрын
Nice! What are the outside corners made of?
@1allstarman Жыл бұрын
Nothing about how to seal the seamsin the metal ? I am doing a repair right now , and every seam in the metal is leaking ! Also ,. does the metal get primer? They are doing things differently than when I went to Goodyear rubber school in Akron , in the 1980's , My supplier said the metal gets primed with the same primer as the rubber, however there is no mention of that here !
@AndrewStergiou2 жыл бұрын
Gee commercial hack Daddy-O keep telling all what to do but never why, how else will we be as stupid as you? America Dumb Dumber and every more as stupid: Rock music these days is as bad as hippy hop.
@garrettbrown18712 жыл бұрын
Company that just did my roof started at the high point of the roof. Not the low. Is that a problem?
@DJ-yp3ui3 ай бұрын
Most likely not in the short term, but you never want water to flow downhill onto gaps, water may seep through once material breaks down over time. These rolled sheets are prone to warping over time/coming loose after years of heating/cooling
@randallgilley97062 жыл бұрын
Rookie
@eduardoflores63902 жыл бұрын
What temperature did you have the welder set to?
@joseluissandovallopez2559 Жыл бұрын
Every person used the wettle in a diferent number. Y used for unsoporter 6 or 6.5 depende the detail. And in the fill i used in 8. I feel good like that. Figured it out how you feel. Better.
@derpherpp2 жыл бұрын
My roof doesn’t have any of this. This is like 3,4 layers of protection
@englishboy1012 жыл бұрын
Where you located?
@fco.ricardoconchas30432 жыл бұрын
I Also use a tpo heating gun to melt the Sims for better adherence. And this is a good product when you don't want or can't do torch.
@jackconnolly26652 жыл бұрын
I'm installing a small, 3 square SA "Liberty" roof. The base sheet was a dream and it worked perfectly. The cap sheet is sucking. I assumed that the same method would be used on the cap sheet but I was wrong. The plastic sheet did not want to pull out easily like the base. It was a combination of the weight and the interference from the overlap area, both the plastic and the slightly rough membrane. Apparently you have to flop half of the whole length over and that will be tricky. If things don't go perfectly, it will be a shit show.
@sirjohnahayfalcon2 жыл бұрын
I had to paint a liberty roll roof with gaco silicone because the Liberty roll wasn’t waterproof
@jackconnolly26652 жыл бұрын
@@sirjohnahayfalcon It was a new product for me and I knew it would be a gamble. I'm 70 so it may last a lifetime :). If not, I will accept the consequences.......or paint it. :)
@evanlovesbears2 жыл бұрын
Honestly looks like shit, and when you need to bust out the caulk like that it's not gonna last. Prefer field fabricated pure tpo scuppers.
@TylerTheCompiler Жыл бұрын
I'm looking for scuppers but damn they're so expensive...where you get yours?
@evanlovesbears2 жыл бұрын
Please don't ever hand bang tpo metal unless you're doing like 2 or 3 pieces. Also, what about corners and how to dry them in??? Or tricky little wall transitions???
@evanlovesbears2 жыл бұрын
Do you wrap the edges, put metal on top of tpo, and cover with am adhesive membrane because it's cheaper than tpo metal? Tpo metal seems way more practical and less labor intensive, which probably costs the same in the long run as this method does. I don't get it. Unless the home owner wants a drip edge that's a certain color?
@gilbertolugo38452 жыл бұрын
i got a pto roof i kmow that is done wrong too they took the membrane and wrap it around my drip adge and then they attach it with a metal board to my facial bored I have A lot of air pockets It looks like a white blanket on the bed This was done like two weeks ago I don’t know what to do with the roofing company if anybody have any suggestions please let me know I wish I could post some pictures of this work done
@takodajakubisn79482 жыл бұрын
Where can you buy this at
@notsosneakypete28582 жыл бұрын
P.s. What's your opinion on using those large 75 pound rollers to press the material down material down?
@terrylutke2 жыл бұрын
OK for a roof-over with recovery board?
@cherjandewit92772 жыл бұрын
🤣🤣🤣🤣🤣🤣🤣
@3619jon2 жыл бұрын
I have this material installed on my flat roof and have an area of ponding. Is it more susceptible than other flat roof materials to damage?
@r3zur3x2 жыл бұрын
No it is not. How big is it and is it near a seam? If it is by a seam just check there's no void, how old is your roof?
@evanlovesbears2 жыл бұрын
Won't harm it at all, most of this material was actually a swimming pool liner before it was a roof material.
@PeakyBlinder2 жыл бұрын
They are called external corners and that is a mess, Go watch some Firestone EPDM videos.
@Brandon-no3vc2 жыл бұрын
Shouldn't you roll each roll sepratly as soon as there set not roll every roll together once you finish job
@Brandon-no3vc2 жыл бұрын
Why use two base sheets? One wasnt even fiber
@jackconnolly26652 жыл бұрын
If you are thinking long term re roofing, the first nailed down base sheet will allow the adhesive layers to be removed easily. If you stick that shit to OSB, it ain't comin off.
@geoffyang99842 жыл бұрын
@@jackconnolly2665 If considering the re-roofing, how about keep the plastic sheet and not pull out from the bottom of the nail base sheet, use nails to hold the base sheet on the plywood roof. Is that working?
@jackconnolly26652 жыл бұрын
@@geoffyang9984 The stuff I used was far too slick with the plastic in place. It would be so slippery that you'd need 10X the nails (and nail holes) to keep it in place. When completed, the adhesive turns it into one large stuck down piece with no nail penetrations.