6 ай бұрын
7 ай бұрын
7 ай бұрын
8 ай бұрын
10 ай бұрын
11 ай бұрын
Пікірлер
@jcole697 11 күн бұрын
Very informative- thanks so much,
@shanecatley7115 Ай бұрын
You just saved me a $200 servicing fee, legend.
@easy2fix14 Ай бұрын
You welcome 😁
@SamFarley098 4 ай бұрын
Who’s idea was it to run the cable underneath the carburettor in the first place?! Thought this would be a 5 minute easy repair and now I'm tearing the whole thing apart lol
@jcmartinez7527 5 ай бұрын
What terrible camshaft placement from Honda… oh well. Beats buying a new engine. Thanks for the tear down video!
@costathierry9854 6 ай бұрын
Bonjour quel est la marque du kit chemise piston merci.
@navahmed-hw2pp 6 ай бұрын
Hi there where’s your work shop ? Could you give me a price for a piston barrel replacement ms181c. Thank u
@TR1CKSHOTS31 7 ай бұрын
Just out of curiosity will the throttle cable keep the trimmer from turning on??? I just bought one on market place (stihl fs100rx) but won’t turn. On. I has spark but won’t turn on. The engine is dirty caked with grease and grime though. Any thoughts on what I should do thanks. Awesome video btw.
@easy2fix14 7 ай бұрын
Hi, if spark is there that's mean wiring is alright. Start with standard diagnostic procedure, after around 5-8 pulls on full choke spark plug should be wet of fuel, then do crankcase vacuum/pressure test, fuel line pressure test ( inc. carb pump diaph. and needle valve ), and check flywheel key.
@weeeves 7 ай бұрын
Not quite as easy as replacing the camshaft on a GCV-190. You're practically having to tear apart the entire motor to do one on these.
@thespartanchief 9 ай бұрын
Quick question, what camera do you use?
@easy2fix14 9 ай бұрын
GoPro Hero 7 Black
@thespartanchief 8 ай бұрын
Awesome! Thank you @@easy2fix14
@thespartanchief 9 ай бұрын
thank you so much, this has saved me and my boss tons of time!!
@tonyd6821 9 ай бұрын
I was given a Stihl 181 and needed a new cylinder and piston that I purchased from China The new cylinder on both side of the carburettor and Mafla has a kind of cover palate with three Philips screws while the old one has pressed rivets look like ...do you thing it ok ? Also the thin plate to set the gup between the fly wheel and the ignition did you by it or you made it ? ....Also the tools for putting the little rings at the end of rod did you buy it ? Thank you
@easy2fix14 9 ай бұрын
Sorry for late answer, been on holiday. There was two types of inlet manifold used in those chainsaws ( make sure your new non-genuine cylinder match to your old inlet manifold ) All special assembly tools I used in this repair are in video description.
@adrianstefan23 9 ай бұрын
👍👍
@---mt1ke 10 ай бұрын
cyk fuh XD
@---mt1ke 10 ай бұрын
nice
@bolo5075 5 жыл бұрын
witam moze mi pan zdradzic jakie przerwy zaworowe w GXV 140?
@easy2fix14 5 жыл бұрын
0.15 ssący i 0.20 wydechowy
@bolo5075 5 жыл бұрын
@@easy2fix14 dzięki za pomoc, a może wie pan ile obrotów powinna być wykręcona śrubka od składu mieszanki w gaźniku gxv 140
@damiansikora5300 4 жыл бұрын
Tak żeby dobrze chidzło,poto jest śrubka żeby regulować
@Ravmx90 4 жыл бұрын
@@bolo5075 1 1/2-2 obroty :)