2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
Пікірлер
@MordecaiFromRegularShow 12 сағат бұрын
3:56 so I just got this far water came out but very slowly and stopped i stuck a straw in there and it didn't go very far at all can't see what I'm hitting but I'm pretty sure it's ice...any advice?
@aacar4095 6 күн бұрын
Best video yet...and my exact engine. Do you fog the intake/cylinders? If so and if I already drained, can I just turn it over with the safety pulled for a few seconds and just fog that way even though not as good? What about bilge...should I dump some antifreeze and run it or something or no issue if drained good? What about removing impeller (manual says to do that and use vaseline on it)?
@ChristopherMoos-i6g Ай бұрын
Do you leave out to freeze plugs?
@jamesprecious1035 2 ай бұрын
Nice work. I have a 99 Response LX and my platform needs the same love. It will be a good winter project. Thanks for posting this. Cheers from BC
@nfaproductions83 2 ай бұрын
Good vid Collin 👌
@nfaproductions83 2 ай бұрын
Shit Connor my bad haha
@mattwhite9670 3 ай бұрын
I was taught by a technician at my local boat shop to use RV antifreeze. I think the reasoning is that it will displace or at least dilute any water that might still be in the engine.
@lucasknecht979 3 ай бұрын
This video is incredibly helpful thank you! Just bought a 98 response and I was on the fence about doing it myself but this video cleared things up a lot! 1 question though do you leave the plugs off during the winter or reinstall after draining?
@connorduester 3 ай бұрын
I usually replace and hook everything back up after just so its ready for the spring. You can leave them out as a quick check if you ever forget if you did it or not tho
@salvadormendez1651 6 ай бұрын
Where do you connect the garden hose to run it out of water ?
@RustyClam 8 ай бұрын
Buy your gas at the airport hundred octane no alcohol.
@DaShawpInc 10 ай бұрын
Ever sick! Lets collab sometime!
@johnM-Jr 10 ай бұрын
Is there a conversion for 98.5 24 valve ?
@paulowen-iy6vm Жыл бұрын
If the boat has a heater dont forget to drain that too. I put an airline on the water inlet hose and blow m manilfolds through. You can also run antifreeze through it) as youn said, but not really needed, the main advantage of the antifreeze is it reduces rusting inside the cast iron parts
@ivanyano667 Жыл бұрын
Hey mate! I have a question, is there any water to drain around the trans fluid system of a direct drive? I do not find a plug anode or any hoses connected directly to it. It’s a mastecraft RTP-1 2006. Thank you for making this video.
@keithyeah8348 Жыл бұрын
Do you fog the engine? I have a 98 Response with a carburetor and people always tell me to fog it.
@davewaldenberg4890 Жыл бұрын
Great job! Explained well and just what i needed! Thank you
@mikemjw4533 Жыл бұрын
Nice job. Do you have a transmission cooler that you need to drain?
@barefootrocker 9 ай бұрын
He pointed at it 5:26, and drained it at 5:46.
@dkofoed Жыл бұрын
Great video, exactly what I was looking for! Just got a 99 response this summer and you break this down very well.
@DaShawpInc Жыл бұрын
Thanks for this awesome video hoss!!!
@FionaRose173 Жыл бұрын
Good video Connor. Can you comment on how to winterize the heater?
@erikrobles4533 Жыл бұрын
Is your hydroboost aftermarket?
@connorduester Жыл бұрын
No. It's a modified unit off of an asteo van from the 90s. All the same units over time, just gotta make the pushrod work with the factory pedal. Same unit as the 97 dodge as well.
@JamesRice-y6w Жыл бұрын
Could be interested in your old windshield frame I have some problems there
@connorduester Жыл бұрын
Sorry, old windshield is already gone
@erikrobles4533 Жыл бұрын
What kind of motor mounts you use on it
@connorduester Жыл бұрын
Second gen dodge mounts. The entire frame and drivetrain is stock 97 dodge
@ColtBryant 5 ай бұрын
I'm about to start one cool to see we are in the same province !
@Nothingschanged Жыл бұрын
Did you have to cut and splice into the existing wire leads to the sensor? Or did you leave it unplugged. Thanks
@billallen7716 Жыл бұрын
Is there a reason why you don't pump any pink fluid through your water lines before you drain
@connorduester Жыл бұрын
There's nothing to freeze if you remove ALL the water from the lines
@johnhill4481 2 жыл бұрын
Thanks for the great video. I’ve got a 93 echelon lx and I’m afraid to go without antifreeze but because of your video I’m going to do it.
@brettyeadon140 2 жыл бұрын
GOOD DAY CONOR I CAME CROSS UR CHANEL AN HAVE TO SAY I 'REALY' LIKE THE MOVIE YOU MAKE I WIL SUPORT THIS PAGE AN HOPE TO SE YOU MAKE MOR MOVIE ABOUT YOUR BOAT; BOATS N HOES N GOBBLES THE USA
@witcher71 2 жыл бұрын
What year and model are the Dodge frame? I see it's a 2nd gen but it looks long like cab and chassis. The cab doesn't seem too loud on video. Cab mounts fairly easy? Any fire wall and front of the frame mods to fit the Chevy cab?
@connorduester 2 жыл бұрын
Yeah its a 2nd gen frame from a 97 extended cab longbed truck. Could'nt believe how well it all fit but the motor is set back 4.75" from where it originally was in the dodge and then the front frame horns were cut back 5" and new bumper mounts were fabbed. For the cab mounts, I used the dodge that I had cut off and shortened and then rewelded to the frame. The front cab mounts I was able to line up and use the factory dodge isolators but the rear I had to move the cab mounting side out to get the isolator beside the frame. The rad support is 95% custom and uses the mounts I cut from the dodge support and brought the frame side in closer toward the frame rail. Fairly easy swap when done this way as opposed to what I see other guys do. All I had to do on the firewall was roll the pinch over an hammer a bit to get the trans dipstick to not contact.
@witcher71 2 жыл бұрын
@@connorduester I was wondering because the engine sits so far forward in the Dodge chassis. I really dig your truck. Kickass build!
@brettyeadon140 2 жыл бұрын
Is it called c/30 because your name is Connor and you’re 30 years old?