You probably can but I would stick with the standard antenna most likely

In the rate profile tab - Besides cutting throttle scale to 50-60% have you tried throttle expo? The more you increase the more dull your throttle stick will feel when moving it

@@PattyFlipz I set throttle scale to 90% because if I reduce it to 50 or 60% it is hard to take off.... Both Throttle MID abnd EXPO I have tham at 0.57 Everyrthing works fine with the rates I appled, but thew problem is that it is very, very hard to keep the same flying level, Any idea?

The idea is you want to tune your throttle until hover point is around mid stick (1500). And as for the quad not keeping level or bobbing up and down, it’s all about practice and more practice. A turn, going over a table, wind will all effect the drone. It’s definitely not as sophisticated to hold a hover as a DJI avata etc.

​@@PattyFlipzwould the gravity option be of help?

For sure!! 😂 thanks for watching

I’m spraying it on some new builds right now, but I won’t be doing a full test / video. I don’t doubt the product but I doubt my spray coverage technique perhaps 😂 For me, I’m personally going to use this spray as a precaution when I fly and land in wet grass, happen to fall in a puddle, or flying in rain. 👍 not flying into a waterfall, but closer to it! there are some other review videos out there already who do all the tests 👍 go check it out

@PattyFlipz if it's not certain...then the old ways of conformal coating still the best way to waterproof right? Rather then a spotty protection

@PattyFlipz but some protection is better then none. Thanks! don't damage your drone

Thanks! Hope you are enjoying your p25?

@PattyFlipz I'm loving it! Imma have to get me a few more colors soon, just to have more flavor. But definitely also interested in the pg5.

Probably need to take it completely apart and reassemble. I guess works best on naked vtx

Gladly! 😂🔥🔥🔥

There is just “enough” room for everything. 😂 thanks man looking forward to your order.

Hi, I use to fly a 1.6” and tried to fly it pretty far without a gps, I found that really fun because it was less intrusive to the environment and unnoticeable to animals or humans. p25 is a 2.5” quad and has a nice sweet spot for freestyle performance and some efficiency for what it is. So basically it’s my burning desire to push the limits of a micro quad and see how they fare. I also have a 4” LR and 7” but it’s crazy how I prefer flying the 2.5” still. The 4” LR I have, the footage is unusable with any slight wind. 7” is heavy and takes up the entire backpack and same 15 minute flight time as p25! (With a 4000mah 6S)

Hi, sorry no I don’t. It’s a bit too much investment so I just sell the frame kits. it’s fun to build for sure 👍 and if it’s your first build, it’s a great first build

I think this quad is around 185g with the naked GoPro . So there’s a bit of room to play with a small 4s battery. If you care about every gram being under sub250 I would recommend filming with a naked o3 air unit. Also, when you film inside and don’t go outside there are no rules with weight. At least in Canada!

@@PattyFlipz thank you 🙏

No problem! Hope it works out 👍💪

You’re welcome!

40mm or under will work 👍

Hi sorry I don’t know, but with inav you can do a reliable altitude hold, or with wings I think they just fly around in circles until you are ready to take control again. In betaflight you hit gps rth it will fly home and land with versions after 4.4. That’s all I know of so far. Cheers

@@PattyFlipz thanks bro for your reply. Yes, it is probably too complicated soft that needed more like AI 😊The idea is that drone should just follow you and make video along the way. Anyway, some more ideas for devs to try. All the best in your hobby!

Hi it’s just a set like a backdrop or stage for the video. Thanks.

Hi, you can get the mount here www.protofpv.com/product-page/mrram-curve-mount but if your quad isn’t proto5 you will need to design yourself a 3d printed GoPro mount for the bottom of your quad

Pretty bad man. Pretty bad. I'll prob get the bear to chase the chimera and run the other way. XD

Hi! You can learn more about it here www.protofpv.com/product-page/mrram-curve-mount

Thanks man!! Yeah it was fun but way too hot!! 🥵 😂

@PattyFlipz yea I live in Phoenix, Arizona..... its way to hot I can barely fly without sweating thru my goggles

Hi , no that’s Proto5

Thanks kibby!

Thanks man!

In bluejay esc configurator? Just make sure all the esc firmware match.

Thanks Bro. Build yours soon k? haha

@PattyFlipz yea soon, got busy with couple of other projects at the moment ...haha ... I look at your frame every day.. the perfection of that frame and the design is really sick...

Thanks Sam

Excellent!! Let us know how it goes.

Did you try longer m2 screws? What’s inside is the internal plastic holder. (Same one that holds the antennas). But DJI uses this same plastic piece to hold the front screws. If the internal plastic antenna holder shifted somehow then it will be hard to screw them in.

@@PattyFlipz Thought about using longer screws, will try and order some. Thanks for the reply and also for this video, great work

Just wanted to add here that it worked by using slightly longer screws from a standard M2-M3 pack, in case anyone runs into the same issue

@LazyPanda21 great glad it worked out