I think a better outdoor outlet or something would work better than an indoor 220v outlet ?

This some wild wild west sh!t here

Thank you!!!❤❤👍🏻👍🏻👍🏻👍🏻

So for the next visitors, the last minutes of the video is all you need. Just unscrew that 1 screw, and move the rail up. BUT! Be careful with one thing! As i see on the video, he makes the same mistake like me. BE SURE that the BOTH rails are at one of their ends (same level). In other ways the seat will be skewed and will end stuck into the middle console. If you have drill machine, you can use it with the spring to make sure, that the rail is at it's end, because if one of the rails touch the end, the motor stops and the other one stops too and doesn't go all the way.

Thank you so much for this video and how did your generator perform after this installation?

Damn good video!

This video help me out big time

*Thank You my Brother* Nice Info I Really Appreciate it***Bless you Brother**

Thanks. Nice to see a good video that explains each step and location

Thanks. Nice to see a good video that explains each step and location

Hi, thanks for the video. It is awesome. Where can I print the instructions step by step? Thanks

Thank you so much, the only video for changing the shaft I believe. I shall give it a try next weekend, it's a Honda Odyssey, but I think the mechanism would still be the same, our shaft came out after someone rear ended us.

“power seat motor drive shaft” is the key word you guys want. i also didnt know the correct wording amazon or google wanted. i did the work, now i posted it here for you fine people!

In the beginning of your video your kid is flipping off the camera my daughter was watching it with me not cool

Definitely wrong rotors

Looks like the wrong rotor

Such a petty Generac crippled this generator by design. What’s the THD?

Thanks so much! I’m having the exact problem with my 03 Honda Pilot. Got a “new” front seat front the junkyard to replace my broken one but that piece was missing. Luckily my old seat had the part but I’ve been trying to figure out how to get it back in and there’s not a lot of info out there on this. So I really appreciate you filming this video!

Did this work as you expected? Any issues with increased load? You could not still pull a 240v load over 37 amps but could pull up to 67/amps on 120 v loads?

Tried it, doesn’t work if it’s only off by a degree or two. The shaft will only link on certain splines

So i bought one with the compressor. Will it work if i shut off the compressor and switch the red and black wire?

I can’t thank you enough for this video. I’m not a car guy. I don’t know how to do these kinds of things. I was already in over my head trying to reupholster my front seat when I accidentally ripped that “bar” out. If I hadn’t seen this video I don’t know how I would have figured this out. Me and my 12 year old son followed your instructions and got it put back in. Thank you so much for taking the time to film and edit these instructions together.

You are awesome! Your video showed exactly what I was looking for. You are a Master Technician!

Very Nice. We have seen the final product and it is true labor of love.

Not related with this video, but the leather of my seat has broken where I sit. I bought a seat with the back broken, can I get the back of my seat and install it to that one?

You need to check your tie rod ends and make sure they’re within 1.5mm or 1 thread of each other.

2008 and later models use flexible cable with screw caps making the process much simpler. Fixed mine in 10 minutes. Thank for very helpful video.

Thanks for the video man! I will be doing this on my Wife's 2014 Laredo soon. I'm getting a code for Inaccurate 2nd gear ratio, as well as ratio clutch 5 defective; the car has almost 150,000 miles, and the fluid has never been changed. The shift from 1st to 2nd has become increasingly worse, and it actually led to both engine mounts failing, as well as the transmission mount failing all within a couple months of each other. Cheers from Princeton, TX!

Hi it's good for us

Cheers mate! Thank you for putting this video up. Saved so much time!

You really helped save me time. Thanks 🙏🙏

Wow your doing double the work I need to show you oG

thanks for telling of faster way to get the 2 pieces apart. glad you were honest at the end and showed the faster way to do it. btw i guessed you needed to be careful to make the sides equal so the seat would slide evenly. this video saved me lots of time.

hello sir, thank you very much, I resolved my dishwasher issue .

Thanks to you, my dishwasher leak will be fixed by tomorrow afternoon 😄

I did this and it worked well but during winter I'm suspecting there is a thermostat stopping it from heating past 20 degrees Celsius.

Nice! I would try some giant washers with o-rings to hold the drum centered. Also make sure to level the machine. I am building one for a mini Keg that is rubber coated (bedliner) for noise suppression. Depending on what you put in it the paint can may inflate and buldge or even blow the lid off. Good luck.

Very nice.. Do you think that it could handle a 5 gallon bucket.?

Thanks man great video

Thank you brother

Excellent video! Thank you Soooo much!!! You saved me hours and probably $$$. The biggest difficulty I had was finding the right replacement for my kenmore. All of the numbers were Whirlpool numbers. Once I found that, the correct item was revealed. This was my information and description: Kenmore Model 665.13543n412 dish washer. Diverter Motor PN W10537869 Diverter Motor Seal Grommet Gasket PN W10195677 Thanks again friend! Dave-Batavia NY

what the name of the parts

do you do this kind of service for clients, if so, where can i find you?

Yep good video thank you

Bro shut up and get to it😭😭😭

I just stripped my screw :(

Great video...detailed and brief

Pozdrav iz Srbije Kako doci do tog GREJACA posto ga u Srbiji nema sve ostalo imam ali taj grejac ne a hteo bi da napravim bas takav

Thanks

Thank You. I found the 2 (of 6) red and black wires that were 12v and reversed them. It reached about 123' F in about 45 min. When my temp controller came in it was able to regulate at 93'F for a 30 minute test. Now I have an $18 (cost of temp controller) (wine cooler-free) incubator to raise my Queen Bees.