That’s horrible LG technology. Their fan sucks. It doesn’t do the job to pull out the lint.

Great video, a few pointers: 1. Don't have to remove the door. 2. Use leaf blower to clean it out but do it outside, or vacuum if inside😅 3. If the stems that hold the rollers on the back of the drum are not worn or marred, just remove the plastic triangle holding pin and replace only the roller, put a small amount of lubricant on the steel stem/roller pin. Saves time. If the stems are worn, no need to remove the back panel, you can get a end wrench on the back bolts. 4. On the vent pipe on your wall inside the house, again, stick a leaf blower in the hole, turn it on and leave it on, go outside, find where it vents to the outside and watch all the debris coming out😊. Just a few tips..

Thanks for this vid. After reading all the comments, I used a hair dryer and heated along the entire area that slides on the sticker side for less than a minute. Worked like a charm.

Thanks for follow up video. I’m looking at this system right now and both your videos were helpful. Was wondering if the RO system had made any difference to taste of your water? I’m on well and my water is clear but tastes a little funky. Wondering if you had same issue or noticed any difference in taste? Thanks again

Water sensor - can you reset it to use it again or is it single use and have 2 buy it again??

Anyone else having problems with the threads on the filter housings? Im installing mine now and the SED filter housing is very tight threading on and refuses to tighten all the way.

Ok, I give. How do you power UV ballast at the garbage disposal outlet if it’s on a switch? I submit to your teachings

If you were living in india they'd have that all pulled apart. Bent back into place. Cut 4 new beams on the lathe and have it painted by lunch.

You should sell me this dirt cheap and I'll finish what you started.

Im hate watching you right now...

I'd bring back Pirate currency. Long live the Pirate Republic.

i feel like the plastic film was there 4 a reason... mayb now u have 2 clean the metal strip over and over again?

That's what she said

You should slurp the royal jelly out with a straw and make a video.

Casting temparature of flask should be 150° less than Melting point of Metal. Use perforated flask with Flange for Wire frame designs or intricated patterns. So you can fasten the Metal flow by vacuuming more area in time. Also you need to blow air into Flask and heat up again so Ashes of resin is eliminated. Then cast.

wow that's a dirty sink, use some bleach and it will shine like new

Check the curve on the emf sensor.. DIN or SAMA? 15:49

On lost foam you always feed from the top

Hi , I tried my vacuum machine but it’s not like your video. Can you tell me your vacuum machine properties?

Cool

Very appreciative for your sharing! 🎉 just wrapped up and am hoping for the best. Tested it and so far, so good! Thanks a million!

Finally finished! U saved my pockets big time bro! Also…. Mine was also very shameful once I took it all apart. 😂 pure shame. Nonetheless my dryer is up and working thank to you My man!!!

I'm pretty sure your water is at zero.. when you add the pac that adds minerals back into the water you're normally will have a 20 to 25 TDS meter reading don't forget to take your water tested to check what chemicals are in it

Bout to do this, seems like hell but I’ll get through it

looks like the species you found was Big Berry Manzanita, that one has very sticky fruits

Great job. Thanks for u time

How to fix red light Red light blinking

Whats the name of that blue device you tested the water with.

I bet that the PID will have melted down by now...?

Try a blow torch. heat cool heat cool and so on

@8:23 There's a massive fart.

Good idea! Thanks! I have a broken patio table and a sheet of warped plywood in the back yard!

Thank you for this. I'll stick to aluminum casting with pla.😊

Anybody remember the 1981 movie Dragonslayer? This really looks like the magical spear from that one.

This water filtration system initially worked so well that I purchased a second one. However, when it was time to replace the filters, the system stopped working. It was a headache trying to get customer care to return my calls and figure out the problem. The system was bypassing the filtration process, resulting in no filtered water. After over a month of struggling with this issue and receiving minimal support from customer care, I finally gave up and replaced the entire system with a different brand. I was very disappointed with the lack of support from Express Water and probably won't be buying from them again, as I expect a company to back up their product when customers need assistance.

Think you didn’t run the vacuum long enough before pouring

I am trying to 3d print with wax resin currently. What trouble shooting worked out for u ? Your prints look amazing.

When all said and done it’s worth your money to just buy a purpose built burnout oven.

Excellent, but i think if you put in the right side of cabinet you have a plenty acces to gauge and UV lamp when time is come to replace it.....IMO

What was the air pressure that you used first

Thanks

Sera que da para Fazer grillz desse jeito??

Thank you. Good video. Appreciate the details about LG steam dryer. Wiring & parts seem essentially identical though obviously a different model. Hope you do more videos on electro mechanical fixes & upgrades, like installing water purification, upgrading sockets to include usb, led light fixture, upgrades, etc. or whatever your trained or exoerience or professional skill set is. We did miss how you installed back rollers, etc., but will find out today. We LUCKED OUT that lint accumulation near ELECTRIC HEATER DID NOT START FIRE, as lint accumulation was so great that it wrapped around & felted around one roller so severely that it broke. (Definitely loose & broke tetaining clip.) All 3 other rollers were ok but were also wrapped with only a litlle lint & clips intact. We clean lint trap after each use & vents annually & outside vent with animal guard monthy. (Should make vacumn nozzle that can reach down to bottom of dryer trap lint catchment as can see lint down there.) Dryer is about 14 years old. First time that we've opened it. Shocked by how much lint accumulated. HOW DOES SO MUCH LINT GET INSIDE DRYER. WHERE IS THE LINT LEAK???? Front panel, blower, etc. Heard it could be the drum that leaks lint, especially if vent clogged. LG Dryers need to be easier to open to inspect & clean lint & be part of periodic maintenance schedule. Disassembled & cleaned everything thus far but the motor which was just vacumned. (Did remove hair wrapped around motor spindle to blower.) Great dryer! Hope it is good for another 15 years with periodic internal inspections for lint!

So we finally discover where all the 10mm stuff goes.

21 ppb is not good. Drinking water should be less than 5 to 0 ppb from a filtration system. Either this system is not working or ready to drink.

where the front and back rollers the same?

Is it made in US

... To be continued...

Good job man. Protect your family.

I wish my city water was that good I'm sitting in 390-450 tds it's crazy