Why they market a device that cannot be used (under development) A car factory would sell a car without an engine, and then later send it to the customer. Lots of promises since May and no change. Chip copying is impossible!! Huge scam.
@carsdiagnosticlab3 күн бұрын
@@attilafeher7194 i don't selling that tool just made fair review about that tool
@attilafeher71943 күн бұрын
@@carsdiagnosticlab It's not your fault, the problem is with the manufacturer.
@@danielmeza2219 yes BMW X5 e70 with cas3 is supported, you need for programming BMW keys voltage supply regulator!
@siegfredreginaldo7 күн бұрын
is it possible to download IMMO PLUS SOFTWARE to other device( android tablet ) ? because i need bigger screen.
@carsdiagnosticlab7 күн бұрын
@@siegfredreginaldo yes by launch official site in page downloads software also in your tablet you have apk file with name base.apk transfer it on android tablet which you want to be installed
@siegfredreginaldo7 күн бұрын
@@carsdiagnosticlab if so, the orig tablet can still be used?
@davidballau50888 күн бұрын
Funktioniert das auf Android und iOS ? Wo kann ich den link her bekommen?
@carsdiagnosticlab8 күн бұрын
@@davidballau5088 android only
@user-go3fr7cc3o9 күн бұрын
Hilo bro Immo plus how many have reset? Do you know between immo plus vs launch3s? Which one is better do you know?
@carsdiagnosticlab9 күн бұрын
@@user-go3fr7cc3o immo plus!!!!!!!
@user-go3fr7cc3o9 күн бұрын
Thank you sooo much bro for your quikly answer❤
@user-im9tn4on5x18 күн бұрын
id 48 copies?
@user-gw1mm5wm3e16 күн бұрын
Can't
@dawwgmedia-d2l21 күн бұрын
Your not doing it properly
@thesmartguy352322 күн бұрын
Jlink V8 or V9 ?
@brunoferreira229024 күн бұрын
ola escrito novo. poderia me explicar como funciona? obrigado
@carsdiagnosticlab24 күн бұрын
@@brunoferreira2290 it not work that's is the terrible!!!!!
24 күн бұрын
Hi, nice video thank you. Did you do that with the IMMO Plus and MCU3 with Xprog3? Can the IMMO PLUS also do cloning of the 7G TCU?
@mohammedawal364025 күн бұрын
Pks no talking
@HardwareTX26 күн бұрын
Same totally useless junk, not even plug to solder direct. Din plug to micro connector, but no micro connector to bare wires to make solder connection. Key reader / transponder reader function only. My xtool scan tool does more then this unit.
@carsdiagnosticlab26 күн бұрын
@@HardwareTX really I don't have a words, and I don't know what to said...and no have news from CGDI for that strange tool ..all people are very disappointed.....autel km100 is very better tool and no so more expensive....by that crap
@georgema62026 күн бұрын
hope cgdi solves what they have promised, otherwise it's a waste of money
@carsdiagnosticlab26 күн бұрын
@@georgema620 really I don't know how they will update it , ok it is possible if they have magic stick 😂😂😂 really very disappointed from them
@georgema62026 күн бұрын
I got mine today and have tried a few things and it feels like a totally useless toy, reads frequency and chip but can't do anything totally disappointing
@rolandoorozco749227 күн бұрын
TODAY IS THE FIRST TIME IUSED IT , IT ONLY READS REMOTES IT DOES NOT PROGRAM ANYTHING. IT IS UNCAPABLE TO PROGRAM A BASIC NISSAN REMOTE MUCH LESS ANY VEHICLE THAT REQUIRES IMMO INTERFACE DO NOT WASTE YOUR MONEY UNTIL ALL ISSUES ARE RESOLVED
@carsdiagnosticlab27 күн бұрын
@@rolandoorozco7492 totally disappointed from CGDI !!!
@rolandoorozco749227 күн бұрын
@@carsdiagnosticlab do not get wrong Cgdi makes other products that I use and I am satisfied with them , I believe this product was rushed Not a lot of thought went into how the end user a tech that needs to program vehicle remotes and smart keys
@Diddy29127 күн бұрын
I has to program new key cards to Megane 2005 . I have Launch CRP919EBT Elite . Can be cards added without pin
@severinonumerosfuertes3859Ай бұрын
con esta se puede trabajar con camiones
@rickypoon918Ай бұрын
Can it be done with Launcher X431 ?
@derekkchungАй бұрын
This car has CAS3+, and you were adding a 2nd key while you have a working key? Can KM100 do all keys lost with CAS3+ ?
@DavdMarАй бұрын
It would've been good if I could actually read the screen on the Autel device instead of getting seasick
@georgiev78Ай бұрын
Здравейте, може ли на thinkdiag 2 да инсталирате prodiag?
@carsdiagnosticlabАй бұрын
Дай телефон или имейл за контакт
@georgiev78Ай бұрын
@@carsdiagnosticlab 0878 315 387
@georgiev78Ай бұрын
@@carsdiagnosticlab 0878 315 387
@danielsayer7884Ай бұрын
Where to get the blank keys? Does it need a certain tyre or will any AliExpress copy work?
@carsdiagnosticlabАй бұрын
Autel km 100 love AliExpress keys 😊 you need clean keys no other
@danielsayer7884Ай бұрын
@@carsdiagnosticlab thanks for quick replay, will order a few 👍🏻
@brettcarney6833Ай бұрын
@danielsayer7884 hey so did you need any special keys in alliance express or order any??
Hi I did bmw1 series from cas3++ and dme aunch Immo elite with xprog 3 I read isn from DME but when putting isn says wrong ant advice please
@noonsahib-je9ik2 ай бұрын
Is thinkdiag 2 a VCI by default ? It doesn’t have passthru function, right ? Only CAN FD
@focusmicro2 ай бұрын
For 8041B6 8041D5, I think change height throw sensor and or check cable for LWR wiring loom for any breaks.
@siegfredreginaldo2 ай бұрын
what is the procedure for this tool to replace an ecu with new one but you have burnt or unreadable old ecu from the car your working on?
@locksmithsandcarprofession24282 ай бұрын
Hi how to get isn akl
@siegfredreginaldo2 ай бұрын
pls make a video with IMMO PLUS do diagnostics, actuation test, and special functions per car brand.
@carsdiagnosticlab2 ай бұрын
Check videos in my channel i have many videos
@siegfredreginaldo2 ай бұрын
how about special functions ,like adaptation, calibration, supply pump learnt clear, and actuation test?
@siegfredreginaldo2 ай бұрын
please make a video of IMMO PLUS do diagnostic , actuation test and special functions under car brands....
@locksmithsandcarprofession24282 ай бұрын
Hi how to read isn to do all lost keys?
@antonispk67602 ай бұрын
Shouldn't you restore the data that you backup from the first dme to the new one ?
@user-yo3sy8cv5c2 ай бұрын
После каких манипуляций удалось получить пин-код ?
@carsdiagnosticlab2 ай бұрын
The card had two old Brocken cards , changed the old (working) in the ingnition and repeat the procedure and get the pin code
@blessevans68082 ай бұрын
I need help I have immo plus I want to learn about using the xprog3 and procedure for programming some vehicles If can get videos or maybe on pendrive or something i will pay Iam in Ghana Waiting for your response
@carsdiagnosticlab2 ай бұрын
Check the manuals in the launch immo allocation and looking for more information in KZbin
@liamol2 ай бұрын
Post how to program it... Renew is a piece of cake.
@carsdiagnosticlab2 ай бұрын
You have two ways 1. To read old ISM an write to new ISM 2. With diagnostic tool Xentry/Launch/Autel to programming to the car just follow the instructions on your diagnostic tool.
@liamol2 ай бұрын
@@carsdiagnosticlab to read from old one and write in new one is ok... But renew it and program with launch or autel that is the problem. It never works.
@carsdiagnosticlab2 ай бұрын
@@liamol Its work with programming with autel and launch ✌️
@liamol2 ай бұрын
@@carsdiagnosticlabmy launch and autel are defective then. By the way many autels in my City.
@user-wz9vp8ng2z2 ай бұрын
Thank you.Why didn’t you immediately write the full data of the original transmission into the new one via the imoprog function launch? Or do you not have the original file?
@carsdiagnosticlab2 ай бұрын
Will programming it on the car.
@alymany9692 ай бұрын
😂😂😂😂😂😂😂😂😂😂😂😂😂
@turkiattrji90733 ай бұрын
👍👍
@mohammadorabi26423 ай бұрын
Is this online coding?
@unlu4ever3 ай бұрын
Is this cloning ore reprogramming the key?learning the key ?
@kurtrichards1593 ай бұрын
"promo sm"
@ecuperformance33203 ай бұрын
Where can be purchased that autel?
@antonispk67603 ай бұрын
Can launch repair a corrupted data on a frm?
@bradleymallia21753 ай бұрын
Hello, how did you get access to the main tablet screen? My one won’t let me
@zxcdarel4 ай бұрын
Do you need a battery maintainer?
@carsdiagnosticlab4 ай бұрын
Yes ! Its 100 recommended!!!
@jetsetjoeyАй бұрын
@@carsdiagnosticlab, is this necessary only if you have a weak battery? If not, WHY???
@carsdiagnosticlabАй бұрын
@@jetsetjoey its 100 necessarily for every programming on BMW to have voltage over 13v , why you can ask BMW factory.....with low voltage you can bricks the programming and you will have big problems