Completely missed correct wiring connection to trailer wire harness and grounding wire to guide.
@arnoldocerda75315 ай бұрын
what if you want a 6 ft 6 inches center to center of leaf springs.
@conkyjoe7 ай бұрын
Those blue connectors are junk. Waterproof butt connectors are a must.
@Jpgundarun Жыл бұрын
I tried to watch but had to turn off when you started talking in that pound and inch gibberish.
@brettcrosse5656 Жыл бұрын
Could you upload future videos without terrible music or even any music at all. It's so distracting I'm going to find some other videos to watch, but I can tell you have exactly the info I want.
@marshallsee97942 жыл бұрын
Just ordered this for my boat trailer& All the hardware and springs. I’m enthused it came so quickly and how well built it looks. Thank y’all for GREAT SERVICE.💪🇺🇸😎🤠👊👊👊
@jovojesic71373 жыл бұрын
Kako doći do osovine i kolika je cena
@deerepower3373 жыл бұрын
it’s not the best brake set the rubber caliber bushings don’t last and allows caliber to go crooked pushing the piston back and then every time the brakes are applied the caliber forces itself back in the correct position and after many cycles the pads wear crooked and there you have it waste of money took mine off after two years and fed the scrap metal dumpster
I hope you guys are safe and thanks for shipping my axle so fast!
@paulovictorfacavocemesmo60577 жыл бұрын
Friend you would have some video with the step by step of the Assembly towing tow dolly car, if you could send me the link to [email protected]
@HomeOwnerRepair8 жыл бұрын
The axle in my ATV trailer has seen better days. Going to replace it soon
@joshavery61038 жыл бұрын
im building a trailer bt i dont know how long to make the axle if the trailer is 1500mm wide ....so do i cut the steel for the axle the same width then weld on the hub kit etc or do i make the steel a bit wider??
@jorgequezadela47278 жыл бұрын
whats the lenght from the front end of the trailer to the middle of a dual axle .on a 6x12?
@joeallen98978 жыл бұрын
60% depending on your load distribution. You'll have a tongue weight that you must stay within a range of. Usually 10% of your over all load.
@jarita45349 жыл бұрын
TRADUZCANLO POR FAVOOOOOOOOOOOOR ¡¡¡.....ESTÁ MUY BUENO :)
@Alatinu9 жыл бұрын
Thank you VM for sharing!. A question: the square shaft is stronger than the cylindrical comparing equal thickness on both?
@lanewoodall729110 жыл бұрын
My boat has been parked in my driveway on the trailer for years. Last time we used it, noticed the trailer bearing going bad and just got it back to its parking spot in time. Jacked the trailer up, removed the wheel, and went to get parts. As luck would have it, my neighbor had houseguests and the 17-year-old with a driver's permit (who enters boot camp in a few weeks) hit the cone on my hitch, knocking the trailer off the jack. He wasn't even backing up, he was going forward. OMG. And he's going to get a gun to use? Fortunately the boat is fine, the garage needs some moulding repaired, and Iuckily the tire we had taken off of the trailer was resting under the axle so when the trailer was pushed off the jack, it rested on the wheel. For 5 years, with the wheels on it, nobody ever hits it. The DAY we take the wheel off, it gets hit. Murphy's Law. Anyway, thanks for this video....will put it to use!!!
@etg195110 жыл бұрын
I recently changed one of my axles on my tandem trailer. The critical measurement as far as I am concerned is of the center to center measurement of the two springs of the trailer assuming that you have leaf springs on your trailer. There is a saddle located on each side of the "Axle" that you will be purchasing and these saddles will sit directly over the leaf springs. The 2 saddles are welded on the axle that you will be purchasing. The saddles are generally a 1-1/2" or so wide metal channel welded near each end of the axle by the hub that your wheels will attach to. At the center of the springs you should find round head bolts about 3/8" to 1/2" diameter. The round head bolts located on the two springs is where you want to take your measurement. So, take a measurement from center to center of the round head bolts on your springs. The holes located on the center bottom flat side of the 2 saddles of the axle that you will be purchasing should line up exactly with the round head bolts that are located on each of the leaf springs. When you install the axle, make sure that the drilled holes on the saddles fit directly over the round head bolts on the 2 leaf springs. Then, install the 2 U-Bolts that attach over each of the saddles (Total of 4 U-Bolts). Next, install your wheels and lug nuts. You are now finished. Congratulations!
@TopChefDan10 жыл бұрын
RIP TO MY EARS!
@timwilkinson968010 жыл бұрын
Give them a Call! i'm Sure they Can Help you out, i got some parts a while back and they were really helpful.
@kyngjoe95453 жыл бұрын
not sure if anyone gives a damn but if you are bored like me during the covid times then you can stream all of the new movies on Instaflixxer. Been streaming with my gf these days :)
@arianares50143 жыл бұрын
@Kyng Joe definitely, have been watching on Instaflixxer for since december myself =)
@FritzMadness10 жыл бұрын
Hi, What's the maximum of a leaf spring can go far in?