IDS 101

Пікірлер

@andriescoetzee4751 4 күн бұрын

Hi I got a module from a auction. I can not add it as it says it was added on a site already. Is there a way to reset it.

@Lebza370 Ай бұрын

Thank you so much for the Video. I hope you can assist me with the same issue. I have 16 zones in total. 7 door contacts and 9 Motion sense passives wired. The door contacts are working properly but all the passives become violated when the panel gets powered up. I have checked continuity using a multimeter and also using a resistor. The wiring is fine. Resorted to removing the end of line resistor and wiring witho eol... No change. I can't seem to figure this out.

@ids_101 24 күн бұрын

Hi, apologies for the late response, make sure dipswitch 1 is on in the motionsense, if its off put it on while power is off then power it on

@sharkfinn6469 Ай бұрын

Do all xwave2 devices connect to onyyx? Also, how can we add a siren

@ids_101 Ай бұрын

Hi, All xwave 2 detectors can work on the Onyyx. it has a built in sounder but a Wireless Siren will be released soon

@AllanMcPherson-z7y 2 ай бұрын

thanks will test it to night

@AllanMcPherson-z7y 2 ай бұрын

hi how can i use the diffrent stay zones

@ids_101 2 ай бұрын

Hi, on the panel you can have up to four stay profiles, for example, 1 profile could be for when you sleeping, you arm the doors and rooms that you want secured but leave your bedroom and kitchen or bathroom bypassed for example so you can wake up drink water or use the bathroom at night

@ids_101 2 ай бұрын

Another profile would be for when you in the lounge but you want the other rooms to be armed but not the lounge or when you leaving kids ik the house and you want them to stay inside, you can bypass the whole inside of the house but leave the doors armed

@AllanMcPherson-z7y 2 ай бұрын

Thanks how do I change between stay zones so when I push number 5 and hold it stay arm number 1 is activated but I would like to us stay 2

@ids_101 2 ай бұрын

there is 3 ways to do it: 1. If you press and hold 5 by default it will arm profile 1, if you press and hold 5 again it will arm profile 2 and disarm profile 1. 2. You can select the default profile before arming by holding down the mode key, scrolling with panic to stay profile then pressing star to enter then pressing the profile number then * to make it default (2 * here to make profile 2 default) then whenever you press and hold 5 it will arm profile 2 first, then pressing and holding 5 again will arm the next profile. 3. If you have the installer code, you can program that whenever you hold down 5, the keypad will always ask you which profile you want to arm.

@lishenthambiran7916 3 ай бұрын

Hi. I'm battling to sync my hyyp device to my phone app. I'm trying to sync but it's not syncing

@ids_101 3 ай бұрын

What errror are tou getting?

@deanbornman77 3 ай бұрын

thank you so much

@SearchFT 3 ай бұрын

Wow, thank you for the nice video. Basic and straight to the point. Thank you. Can you please make a video adding the long white IDS remotes to the IDS X64 keypad? I've managed to put two remotes on the receiver, which is connected to the keypad, but by some reason only the one remote can cancel the alarm when triggered. So both can ARM, but only one can DISARM. I also want button 3 to be able to do ARM STAY, because I thought functions for button 1 & 3 are default (1) ARM/Disarm & (3 )STAY ARM. I've downloaded the installer-, User- and Receiver Manuals, but some of the steps are confusing. I used the program the panel, but now on the same steps just after entering the receiver number I get asked "Code/Slot + * " I can't remember that it asked me that and it is not displayed in the stems in the manual. Thank you sir.

@ids_101 3 ай бұрын

Please follow the below linked video: kzbin.info/www/bejne/jpScc5mVmL6XrdU Make sure you create a code for each remote

@ThuyNguyen-er5ne 4 ай бұрын

The video is too blur, so it is hard to see the number when you pressed.

@ids_101 4 ай бұрын

Hi, which number are you unable to see?

@CliffordThulo 5 ай бұрын

How to delete site

@ids_101 4 ай бұрын

kzbin.infopyOKnAiSWvs?feature=share

@ThuyNguyen-er5ne 5 ай бұрын

Does this product be ready to sell in Australia?

@ids_101 4 ай бұрын

Yes it should, as it just requires an internet connection to work

@nombulelomthombeni4679 5 ай бұрын

What is the error if red flash flickers continuously? How does one stop it from flashing while unarmed.

@ids_101 4 ай бұрын

Hi, Flashing red LED means there is a trouble on the keypad (Low battery, Siren Trouble etc.).You need to hold down the number 7 key on the Keypad and it will display what the trouble is. once resolved the LED will be solid

@previnvandayar2560 5 ай бұрын

Thank you for the reply, however I don't have the installer code

@previnvandayar2560 5 ай бұрын

Hi. How do you move a zone from one partition to another

@ids_101 5 ай бұрын

Eg. Moving zone 3 from p1 to p3, You will need to do the following Enter the installer code * Enter 201 * for p1 Enter 3 * for zone 3, zone 3 should be Y, press * again to make it N Enter #, then press 203 * for p3 Enter 3 *, zone 3 should be N, enter * again to make it Y. Press ## to exit

@MotanyaneMathumetse 5 ай бұрын

Need help , the sync is not working

@ids_101 5 ай бұрын

Where are you getting stuck when you sync?

@lishenthambiran7916 3 ай бұрын

Me to. Trying to sync. It's not syncing

@virenbishun4362 6 ай бұрын

Hi....I had some trouble with thr Hyyp app where it said it couldn't connect to HYYP. Some comments said to log out and back in ....I logged out now the app says my email and pass is wrong credentials. When I ask for forgot password reset....it's says email not verified....how can I solve this problem as I really use the HYYP daily. Thanks alot.

@ids_101 6 ай бұрын

Hi, Please contact the HYYP standby line on 0871597341 and select option number 2 for HYYP, have your cellphone number and the email address that you use to login to the app and they will happily assist, alternatively you can pop me a mail on [email protected] and with those details and i can try and assist

@coralrofail8108 7 ай бұрын

Hello, I don’t know if you can help me, but my HYYP says “offline” and I have no idea how to get it back online?

@ids_101 7 ай бұрын

Hi, its usually because of a power or network issue. You can contact the IDS Helpdesk on 0871597341 and select the HYYP option. They have someone on standby after hours who can assist

@christiaangribnitz7641 7 ай бұрын

Thank you. The 🎥 helped very much

@ids_101 7 ай бұрын

Glad I could help🤙, Please consider subscribing if you have not already

@hopeschuppe 7 ай бұрын

"Promo SM"

@Wanderlust9WP 7 ай бұрын

how do I check the panel version?

@ids_101 7 ай бұрын

Hold down the * key until keypad beeps then press. * again

@Wanderlust9WP 7 ай бұрын

@ids_101 Thank you

@Wanderlust9WP 7 ай бұрын

I've had an installation that that's temperamental it was really difficult to enrol the sensors even though the panel and sensors plus receiver were all the correct spec. now the sensors go offline, and sometimes they come online if I reboot the panel. any idea what would cause that?

@mfundonyembe 7 ай бұрын

@Wanderlust9WP There was a bug on the Xwave2 receivers where it would lose the sensors but get them back on a restart, you would need to swap out the receiver for one with a blue sticker where they fixed the issue but what you can try do is just default the receiver by putting all dipswitches down, powering off receiver putting all dipswitches up, powering up and leave it on for 5 seconds, power down again then put all dipswitches down and just leave the one that younare using then power up again, then wait for the trouble LED to stop flashing and only network is on then you can test and monitor again. This will just default the receiver and not delete the serial numbers.

@Wanderlust9WP 7 ай бұрын

@@mfundonyembe that's most helpful. is the blue sticker on the box or the receiver pcb?

@edwinnetto6248 7 ай бұрын

Sad that the IDS App doest facilitate configuration!

@issufojamal4278 9 ай бұрын

Hey thank you very much for the video, I'm experiencing a 'P1 Not Ready' with a Zone issue of v14 Zone 14 could you please help me solve this?

@ids_101 9 ай бұрын

Hi, if zone 14 is a wired zone, remove everything connected to zone 14 and connect just a 3K3 Resistor (it has orange orange red and gold bands). If the zone closes then the panel is fine, the issue might be wiring or the detector is not closing the zone.

@ids_101 9 ай бұрын

To test the wiring without a multimeter, you can remove the resistor and wire it back to zone 14 but take out the wiring out of the detector and join the two wires on the detector side with a 3K3 resistor, if the zone closes the wiring is fine, if it stays open the cable is the issue.

@ids_101 9 ай бұрын

If its a wireless zone, it might have lost connection to the panel, check if the power light is flashing, of flashing, it might be a battery issue, hold down number 7 key to check, you also might need to just remove the battery and put it back in to regain connection with the receiver, if issue persists, delete then re-add wireless zone

@dolorescorkery 11 ай бұрын

👇 *promo sm*

@MSU. 11 ай бұрын

Does it work with IDS 806 wired?

@ids_101 11 ай бұрын

Yes it does, also with X-Series and IDS805(you require a keybus interface for the IDS805)

@waynegeerdts2013 Жыл бұрын

Hi @IDS_101 I hope you can help - I have an X64series with an onboard expander plus a wired smart expander… now and again I get a message stating “Expander Module Failure: Area 0 Front Door”… this sometimes causes my alarm to go off as well and then all zones connected to the expander are active… How do I fix this? (Take note that the smart expander is new and the led light is continuously on)… after the message is received, when I walk past a PIR connected to the Expander, the message goes away and all zones are closed again (meaning I can arm again)…. But then an hour or so later the issue occurs again… What is causing this?

@edmundoloforte1251 Жыл бұрын

Hello, I got this alarm system as a gift, but it always says not ready to arm, can you help me please?

@ids_101 Жыл бұрын

Hi, does it flash any zone number when it says not reeady to arm?

@cornellserfontein9778 Жыл бұрын

Hi there, any idea how to update triggers on other users apps? If I load a trigger it doesn’t show up on other users apps

@ids_101 Жыл бұрын

Hi, @cornellserfontein9778 you will need to enable the the trigger for the sub user using the master users phone, on the app, you will open the site > tap the 2 people icon at the top right to show users> on the list of users, tap the pencil icon at the top right > tap on the user that you want to edit> toggle on the trigger for that user > tap on save changes. The sub user will need to logout and log back in to see the changes.

@AkshaySingh-rf4vs Жыл бұрын

Any ideas on why the hyyp app doesn't work well with a dahua DVR ?

@ids_101 Жыл бұрын

They are currently working on an app update to resolve the HYYP CCTV issues

@AkshaySingh-rf4vs Жыл бұрын

@@ids_101 Thank you.

@ids_101 Жыл бұрын

There is a new app update v4.2.2 which has been released that solves the CCTV issues

@nontuthukomadinane2147 Жыл бұрын

How do I stop the beeping sound?😢

@ids_101 Жыл бұрын

Hi, where are you getting the beeping sound? On the keypad or app?

@05jpb Жыл бұрын

Thanx for the reply I wired the led without a resistor as it wad 12v led. Key pad was faulty had to replace it expensive one but had to be done thanx for the help you videos help alot. 👍

@05jpb Жыл бұрын

Hi there what resistor to u use to wire up the led like your one in the video. 2nd question. What does it mean when my panel shows version 1.08 busy and both power and arm lights are flashing on panal?

@ids_101 Жыл бұрын

Hi @05jpb in the video, i use a 3k3 resistor but you can also use a 2k resistor, if its a 12V LED like those bright ones you can get away without using a resistor.

@ids_101 Жыл бұрын

Version 1.08 busy means the keypad is not communicating with the panel you can check if your data wires are connected correctly, default just the keypad by holding down 1&3 keys on the keypad, power down and power up while holding 1&3 then press # to register keypad. Lastly you can check the status LED on the panel, it should flash once every second, if its not then it might be a panel issue.

@ltvtech Жыл бұрын

How easy is it to link Hypp woreless to the modem? Maybe got a video?

@ids_101 Жыл бұрын

Its quite easy, it gets diificult when the router/modem is further away from the modem as the WPS signal is not as strong as the actual WI-FI signal, i always recommend you wire the HYYP wireless on a battery and put it next to the router, press the WPS button on the module and when the 3 green LEDs are flashing clockwise press and hold the wps button on the router for 3-5 seconds and 1 of the 3 green LEDs (Server Auth) will be solid to show that its online then you can take it back to the panel and it will auto connect but il post a video soon.

@toptenuniverse5437 Жыл бұрын

How do I make someone else master

@ids_101 Жыл бұрын

You can only have one person as a master, everyone else can only be added as a sub user

@theem0139 Жыл бұрын

Thanks. This is very helpful

@raeesfataar8196 Жыл бұрын

Thank you so much, this fixed my issue 😃

@shahiedkhan883 Жыл бұрын

You omitted a step. After power down and putting jumper on J3 Connect USB to Serial Adapter on Control Panel open up the Bootloader File in Swift Power up Control Panel and Begin Bootloader Immediately .... or while Keypad still showing BUSY

@gerhardusvaneyssen5774 2 жыл бұрын

where can I find the software ?

@ids_101 Жыл бұрын

At idsprotect.co.za under training and support > intrusion

Ең жақсы KZbin

Пікірлер