Hi - Thanks for your videos. Is there a fuse number particular to the rear offside central lock. The CL has gone twice on my corsa E 2015.
@yaelsanchez305723 күн бұрын
I’m still waiting for the review on the smoke tester🥲
@williamjohnston492324 күн бұрын
Driving a 1.4 2015 corsa and every time I sit still service esc comes on the screen with the traction control light, also the service engine light stays on all the time, I changed the battery and this fixed it for a few hours but now they’re back on
@mariathornton291627 күн бұрын
Omg thank you. My boiler was broken and now we knew why.
@catalin2768Ай бұрын
Hello, nice video. So in this case, you just replace the water pump and that s it ?
@jonsutyautomotiverepair1993Ай бұрын
Yes, that’s correct
@6thedaysАй бұрын
Could a lack of battery cause a failure in the front camera???
@jonsutyautomotiverepair1993Ай бұрын
@6thedays yes
@Jimmy_FilmsАй бұрын
Thanks for the fast reply man,didn’t think you would see it as the video is 3 years old.Was it easy to replace ?
@jonsutyautomotiverepair1993Ай бұрын
@@Jimmy_Films yeah easy enough, nothing else comes off I don’t think
@Jimmy_FilmsАй бұрын
Alright man,my car has this same issue.Was it the starter motor then ?
@jonsutyautomotiverepair1993Ай бұрын
Yeah it was the starter motor, unfortunately I didn’t film the replacement as it was winter and snowing like mad and back then no garage to work in, they are however quite easy to do, they are done from underneath and withdrawn above the driveshaft if I remember correctly
@ruslanrodz-k4s2 ай бұрын
Thanks m8. Sorted for now until new fan arrives.
@JackT212 ай бұрын
Head gaskets as well there common
@MrNappySlapper2 ай бұрын
Basic question, but how do you remove the big white panel?
@grahamparsons12192 ай бұрын
Great help, thanks. Yes It is possible to do this alone. Remove the rear light cluster, cut sensor holes, then feed a length of stiff 13amp or similar cable down into the inside of the bumper through the gap revealed after removing the light cluster. Direct it along to the furthest hole, it will probably drop down below the bumper. Feed the sensor wire through the hole, it will probably drop below the bumper as well. Secure wire to cable and pull through. Took me less than an hour to complete this part of process. Another tip, lubricate bumper hole and sensor grips with oil or grease, they slip in easily.
@greenlettuce73 ай бұрын
what if the radiator light is flashing instead?
@EddiesCustomsandRestorations3 ай бұрын
Good job man!
@tomsangiuliano80323 ай бұрын
That wasn’t seized up at all.
@bujasovara94463 ай бұрын
I have a 2015 corsa ecoflex 1L is mixing water with oil in the water bottle
@zdnekpicha79563 ай бұрын
OK 👍
@paulkomn9464 ай бұрын
My friend what is the torque tightening in Nm on each bolt on camshaft cover?
@jonsutyautomotiverepair19934 ай бұрын
@@paulkomn946 only 8nm
@paulkomn9464 ай бұрын
@@jonsutyautomotiverepair1993 THANK YOU VERY MUCH
@regal1634 ай бұрын
Hi again, I cannot get my head around the tyre pressure indicator, it says, "check tyre pressures" I pump the tyres to wear I want them, 3 people eco, and put the "tyre pressure learning active" mode on but not sure what to do after this because next morning it still reads on start up, "check tyre pressures", can you help please.
@jonsutyautomotiverepair19934 ай бұрын
@@regal163 try doing a re learn using a tool called el 50448. Copy versions of said tool are only around £5 on eBay
@jonsutyautomotiverepair19934 ай бұрын
@@regal163 el-50448
@jonsutyautomotiverepair19934 ай бұрын
@@regal163 whilst that’s on order, adjust the pressures and take it for a drive
@bariscam8434 ай бұрын
Bro how is reset AEB
@jrbeidnendu24544 ай бұрын
hi mate. can the purge valve cause a ticking noise at idle that follows your engine speed up if the accelerator is pressed
@jonsutyautomotiverepair19934 ай бұрын
@@jrbeidnendu2454 yes
@jrbeidnendu24544 ай бұрын
@@jonsutyautomotiverepair1993 cheers mate thank you
@fumaninjaknownoequal3 ай бұрын
That's the cooking fan..
@mitchell_97094 ай бұрын
Hi I have notice a weird scraping/grinding sound when setting off in 1st it only happens when i put a lot of gas on when lifting off the clutch biting point but if I do it with a little bit of gas then the sound doesn't occur it only happens in 1st and 2nd gear. any ideas what it could be ? its almost as if it like when the car move more due to accelerating faster something starts scarping off something possibly
@jonsutyautomotiverepair19934 ай бұрын
@@mitchell_9709 nothing common that springs to mind, perhaps check the engine mounts to see if something it’s flexing
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@mesutmermutlu69235 ай бұрын
How can we solve the problem “service ESC” 2016 Corsa E 1.4 engine 90 HP
@jonsutyautomotiverepair19935 ай бұрын
@@mesutmermutlu6923 possibly replace the coil pack
@mesutmermutlu69235 ай бұрын
@@jonsutyautomotiverepair1993 thank you
@DWUKTA4 ай бұрын
Purge valve
@ibrahimoussifi5544Ай бұрын
Hello Is your car manual or automatik ? Do you think this car is generally reliable ?
@mesutmermutlu6923Ай бұрын
@ my car is automatic. This car is a reliable car.
@ajenergy42516 ай бұрын
And finally... I'll share some advice for anyone who jas a similar issue.... While trying to change the thermostat - there are 3 bolts with TX star head size e10. All bolts on this model seem to be TX star heads of varying sizes... Anyway, one bolt snapped and i solved this by filing down the barrel that was left in situ (more by luck than judgement as it started wearing down when using the mole grips😂) So I get an e6 TX star head onto it, gently tapped it in til tight, then used ratchet to loosen. Hope this helps anyone who has similar issues.
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@ajenergy42516 ай бұрын
Re initial query about 'engine overheating idle engine' - I replaced thermostat but still getting the warning and now thinking it must be temperature sensor. Seen vids on one going into radiator but also thread on corsa forum says there are 2 sensors - any idea where the other is located? Once again, thanks in advance for any help or advice.
@jonsutyautomotiverepair19936 ай бұрын
@@ajenergy4251 further down there is coolant temperate sensor B, sits on the pipe at the bottom near the readiator
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@ajenergy42516 ай бұрын
Hi man. Just watched video and thanks for the tips. Came across this as looking for a solution to engine overheating - but before I go there i noticed at approx 4 mins into this video you mentioned a "timing chain" I have been wondering since I bought car - corsa e 1.4 sri 2015 - whether it was belt or chain and when to replace?? Car has done 101000 miles. Any advice greatly appreciated.
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@kowskyyyyy6 ай бұрын
Hi, I have a corsa 2015, my wipers are keep breaking, changed linkage and motor, shifter as well. Relay and fuses. I think it might be ECU problems… anyone can help!
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@gisgoss6 ай бұрын
For those with the p0171 lean code, check the evap purge valve. The original bosch ones seem to constantly fail and are the likely culprit for that code. In my case the engine was drinking way more fuel, ran rough and was giving off a fuel smell every so often. Along with a few misfires. Changing the evap valve fixed it completely. Take it out, if you can blow through it then it's knackered and needs replacing since the valve is stuck open. Heard online people using maf sensor cleaner to spray in and fix it but honestly just replace the part. Cheap and easy to do.
@Baza7657 ай бұрын
Top vid mate,would you know why my radio stays on when i stop the car,turn off, and remove the key,it used to go off straight away,but now it takes about 20 seconds or i turn it of at the knob,,Cheer Baza PS Could it be to do with the ignition barrel
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@kevintrace53967 ай бұрын
Endless problems with the car keep away from em
@jonsutyautomotiverepair19937 ай бұрын
100% agree, best thing is a Range Rover or Tesla
@andrewlace8 ай бұрын
I found using the small with the large or alternating gives you better flexibility most springs now are tapered, variable rate or whatever they want to call it. In short there is no advance in technology without minor inconvenience for the shop tech 🤗
@jonsutyautomotiverepair19938 ай бұрын
Good tip
@SkrawnCPT8 ай бұрын
My 2015 1.0L ecoflex has no power. Its like someone has removed the turbo. I put my foot flat and the car doesnt respond. The timing chain was replaced 41000km ago. Current mikeage is 241000. Took iff the intake and the turbo is not stuck. It does turn. Haven't checked while the car is running. Engine light is on. Please help.
@jonsutyautomotiverepair19938 ай бұрын
Any fault codes ?
@rockwell6668 ай бұрын
Thanks for this video, I've just installed reversing sensors on my Skoda Fabia Mark 2 2012 12V and it was very helpful. Here's some advice based on my experiences... 1) Check you can remove the plastic trims *before* you start drilling holes etc as I found the "nut" that holds the light cluster in place had rusted onto the screw thread and it took ages to free it up! 2) Not having the taps shown in the video, I tried using a "chocolate block" wire connector and cutting the wires to the reversing light, unfortunately the clearance between the back of the cluster and the bodywork was too narrow for it to fit, so I had to crimp on bullet connectors instead. 3) It's not actually "impossible" to get the wires from the sensors to the control unit on your own. I got some stiff garden wire and fed it through the left most sensor hole, then made a loop to secure the end of each sensor wire and pulled it back. It was a bit fiddly, but it saves having to remove the bumper :-) Oh, and make sure you disconnect the boot light and don't leave the ignition on, otherwise you'll flatten the battery. Guess how I know that... Anyway, again my thanks for the useful video.
@triple_h_gaming39138 ай бұрын
Hi , #jon suty. Very helpfull video . However I have a corsa e vxr and I constantly get a service esc warning ... any help on this would be great
@jonsutyautomotiverepair19938 ай бұрын
Does it misfire also ?
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@SharronColeWhite8 ай бұрын
What did you tell 🤷🏾♀️
@juliebaxter35648 ай бұрын
I had a 2017 Corsa that had awful leaks in the offside rear and front foot wells. There was mould everywhere and had seedlings growing in it. Formally complained about it no joy. The water seeped when stepping into it making the bottom of my jeans wet. Had to get rid of it. Happy with my new car.
@leslierogers12769 ай бұрын
I had a 2016 corsa sting (90)from new (5miles on it when I picked it up ) the only fault I had was the coil pack had a very slight misfire at 3000 rpm at about 50k, sold the car at 103,000 miles, had it serviced at vx every year, never replaced back tyres and only ever replaced the front tyres once, never had clutch problems or wiper problems, and no speedo problems,it always passed its mot no advisory’s, maybe I was the lucky , just hope my Hyundai is just as good, why did I not buy another corsa there just too expensive and it’s French owned might as well buy a 308, not for me
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have in your corsa ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@steveb401210 ай бұрын
Thanks for this, my lad is just learning to drive and these Corsas are eye catchers. However, I think we'll look elsewhere.
@vuyisasholo135410 ай бұрын
Im driving opel Corsa Vauxhall 2015 model ,when the engine is cold it take sometiem to start,but when its hot i dont get any struggle
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@tabs814011 ай бұрын
Good morning my corsa losing power replaced throttle body and electronic accelerator and no change please assist
@jonsutyautomotiverepair199311 ай бұрын
What lead you to replace this parts ? What dtcs do you have ?
@vuyisasholo135410 ай бұрын
Check your clutch
@detectoristmal251711 ай бұрын
My corsa E rain censer came off the window it's z nightmare
@jonsutyautomotiverepair199311 ай бұрын
Easy enough to replace but now has it fallen off ?
@detectoristmal251711 ай бұрын
@@jonsutyautomotiverepair1993 don't now gran kids playing
@simonrowe823911 ай бұрын
Thanks mate. Legend 👍
@regal16311 ай бұрын
I'm going to ask you a question that I have been googling, binging and even went to my Vauxhall dealer who sold me my 2019 Corsa, which is exactly the fuse for the reversing lights on my car, all they said was, there's to boxes one in the engine bay, at which point I could have screamed😅, I would like to know where it is or even what amp it is without taking out every single fuse, its not an MOT fail or I would have had to pay Vauxhall a large amount of money just to replace it, the reversing lights fuse is no where in the manual, any help you can give will be great👍👍👍.
@jonsutyautomotiverepair199311 ай бұрын
There isn’t one as far as I’m aware, I. Sure it’s switched by the Bcm. I’d check the reverse light switch located on the front of the gearbox, that’s the likely culprit
@regal16311 ай бұрын
Thank you for your reply, I will check that.
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@rvist111 ай бұрын
Could you please advise what battery for me to get for my same shape corsa e 2015 apparently these corsas all come with a varta start stop battery even if your car is not start stop which mine is not. I do not have a radio code and have read that the battery swap needs to be done within 30 seconds or you will have to get the radio code please can you advise
@ibrahimoussifi5544Ай бұрын
Hello What engine do you have ? Is your car manual or automatik ? Do you think this car is generally reliable ?
@rvist111 ай бұрын
I personally believe the coil pack issue is caused by when the spark plug gets messed up and generally down to not using the correct manufacturer recommended spark plug
@justincarroll9846 Жыл бұрын
Heated windscreen only works on 1 side while the other side remains frosted. Bushes in wiper motor where.Thats the only problem so far.
@jonsutyautomotiverepair1993 Жыл бұрын
Those are common on any car tbf
@PikaStu69 Жыл бұрын
Hi , I want to check the air mix servo on my muns corsa c 2006, how do I get to it, any help will be appreciated. Many thanks.
@williamoldham3358 Жыл бұрын
Nice work. Thanks.
@garethjones8047 Жыл бұрын
Greetings from North Wales. Im thinking of getting one this make. Have you had much use out of it yet? If xo, does it work ok?
@jonsutyautomotiverepair1993 Жыл бұрын
I’ve used it but I don’t rate it that much, it’s more designed for 4x4/ bigger springs so I really struggle with small cars which is mostly what I work on.
@garethjones8047 Жыл бұрын
@@jonsutyautomotiverepair1993 Thanks for the reply. Im a Hgv mechanic so I dont do many coil springs but the guys where I go for MOT told me they don't rate theirs much either. Their preferred tool is the big cups that you can use with an impact gun, they reckon its far superior. All the best Pal
@andrewlace8 ай бұрын
I've used mine a bit. At the time price was comparable to ebay stuff. From new it leaked from the oring on the relief valve. If you find the same drain oil, piston comes out, take the oring to a hydraulic workshop and they'll measure and fit an oring for a few cents plus gold coin donation to beer o clock fund. No after sales support from vevor. Replaced the oring so far it's fine. No more leaks. It does have very poor paint and welds on it. They may change models. My advice is the same as other workshops: hydraulic is more to go wrong. If you can get a screw down one it'll be much more reliable. Also the spring holders are cast and quite weak. One of the bigger ones failed with use. Just keep in mind it is nowhere near the quality of a quality unit. Jacktek sk-3000 is showing in my feed as I'm writing this lol. I'd buy one at ebay prices. Vevor is now a lot more expensive unless it's on special. I will now buy basic stuff from vevor but I don't consider them any better than ebay and I don't expect any support or warranty from them. Chinese rebadgers.
@garethjones80478 ай бұрын
@@andrewlace Thanks so much for your reply, good advice
@georgi6722 Жыл бұрын
right day light is not working , it not the light bulb , is not the fuse ....