Wahoo International

Пікірлер

@GIF_CANCEL 29 күн бұрын

My Blalah Bullyboard just arrived yesterday. Can't wait to try it out. Beautiful board.

@GIF_CANCEL Ай бұрын

This inspirers me. Later I finally ordered a BullyBoard and it arrives in two days. Here in Florida.

@banks5898 Ай бұрын

Where do I even find plastic sheet like that?

@aaronpovsurf 5 күн бұрын

cuz a ziploc bag

@banks5898 Ай бұрын

Mine didn’t come with plastic though

@aaronpovsurf 5 күн бұрын

ziploc cutout

@GIF_CANCEL 2 ай бұрын

That's the best. I wanna get a Bully bodyboard.

@user-gl6tb6my9y 4 ай бұрын

What is the wattage on your UV light and where did you get it?

@cwl1052 5 ай бұрын

香港邊度有得買

@AFrames763 8 ай бұрын

Really cool and mellow vid

@crypttonite 8 ай бұрын

does resin alone dry clear?

@arcticville637 10 ай бұрын

What is the meaning of those steel balls in chamber?

@paxchristi2014 10 ай бұрын

Use a heat gun and cure it faster. Edit: UV rays artificially would also be helpful

@5naxalotl 7 ай бұрын

heat gun will thin it more than it cures it

@paxchristi2014 7 ай бұрын

@5naxalotl ok thank you

@Mherkava 11 ай бұрын

Can I sand down the sealer to nearly bare wood before applying the gloss finish?

@jeffduke9686 Жыл бұрын

I am curious about the light that you use here. Can you tell me the wattage and where you purchased it from? Thanks

@rydebeachlifeguards9743 Жыл бұрын

What is the red rope you used? Is the rail strong enough for that then?

@deanboful Жыл бұрын

Get a new router and use a jig.

@j.vonhogen9650 Жыл бұрын

Would this method work for pianos and grand pianos too? Is there a 'piano black' version of this polyester product that would be suitable for finishing pianos?

@saltyhumansWX Жыл бұрын

Aftermarket transom on there?

@thouaregreat 7 ай бұрын

Lifesled makes there own custom transom.

@garyfisher7007 Жыл бұрын

Not necessary to store at 45 degrees. Room temperature is ok

@Golgafrinchamdent Жыл бұрын

On the Wahoo website it says to keep this in the refrigerator at 45-50 degrees. Is that necessary? I'd like to take it with me in my vehicle for mobile work. Thanks.

@SerenityGuitars Жыл бұрын

Unless something else is going on, this video was created by the Highland Guitars youtube channel. Do not support this channel with possibly stolen content unless they clear up this issue with Highland Guitars.

@dadguru7973 Жыл бұрын

you've got such a great chill vibe - thanks man!

@MrTomasharrison Жыл бұрын

My board likes this video 💔🥲

@retroquest3579 Жыл бұрын

Does anyone know how this resin works with an archtop guitar like a Les Paul or a Dinky? It doesn't seem like I would be able to let it sit before curing, since it's not a flat surface to sit on... ?

@carlapsirris912 Жыл бұрын

Hello, so did you drill through the foam prior to installing the finbox ? What drill pieces did you use?

@mannyaldama2450 Жыл бұрын

ripper

Жыл бұрын

This product does have a strong odour which will give you a headache - good ventilation and vapour respirator best. The video uses way too much of the product - 10-12 drops would have done it. Spread it with a silicone glass wiper and get most off before curing - unless you enjoy sanding😆😆

Жыл бұрын

Vid applies way too much - most ends up in the sponge! 10-12 drops would have done that surface, easy! Spread it with a silicone glass wiper and get as much off as possible before curing, unless you enjoy sanding😆😆

@stringtheoryx Жыл бұрын

Do you prefer this Solarez Gloss Polyester over Solarez "I Can't Believe It's Not Lacquer"? What differences have you found?

@WahooInternationalInc Жыл бұрын

The choice is in the craftsmen hands. We created ICBINL to mimic the feel and look of traditional guitar body top coats but people have been making guitars with poly for years. The choice is yours

@IndyRockStar Жыл бұрын

This guy makes it look too easy. It's not hard, but it is a little tricky if you're not used to UV cured coatings. I recommend NOT using a paint brush. Use a foam brush or a make foundation applicator. I tried the paint brush and it really hard to get an even finish. If you try to fix it when it's too thick it clumps up and it becomes impossible to completely fix. Key is to apply as thin and even as a layer as you possibly can and repeat as many time as possible. Finish sand between coats (DO NOT USE A POWER SANDER - It will burn the clear coat and cause the stain to recede). Also DO NOT be a hero. Work on the guitar front and then the back (or vice versa) especially if your dealing with a guitar with binding.

@SoCalSurfer69 Жыл бұрын

Can you use this for a replacement for varnish on boats or kayaks?

@Celticsaint777 Жыл бұрын

Why brand of water based wood dye did you use????

@outerrealm Жыл бұрын

PVC pipe is nature's tinkertoys/legos for just about any improvised construction, framing or other device!

@thedm8531 Жыл бұрын

Better than watching Bob Ross paint I’d say 👏🏻 and that OG SD shirt ⚡️

@clarityhouston3499 2 жыл бұрын

DO you work under fluorescent tube lights? Im just wondering what kind of lighting you can work under that wont start to cure the resin while you are still working with it.

@josh_corwin 2 жыл бұрын

The pump adapter mine came with is too short to latch on. Very disappointed

@CJ-bw2nm 2 жыл бұрын

Thank you for such a smooth and informative video. Been trying to find a good video for foam stains and you even threw that in there.

@paulwary 2 жыл бұрын

Respirators and dust masks. You'll live longer.

@wtfftw24 2 жыл бұрын

How do you set and be sure that the fin box is at 90° degrees 📐 whiteout pre installing a fin as normally is done??

@jungbechtospk40 2 жыл бұрын

Woodglut is a good solution for every woodworker.

@RocketDog73 2 жыл бұрын

Interesting that how they performed ‘this time tomorrow’ was not part of the video. Save your money and do not buy the stuff and put it towards new fins.