My Midea S8+ had a "Please clean the cliff sensor" alert despite cleaning it, I wanted to open it but couldn't figure out how, thanks to this video I managed to open it and turns out 1 cable was snapped somehow, soldered it and working again, also allowed me to clean it properly inside. Thank you!

Спасибо, Брат

Muchisimas gracias, me sirvio para reparar mi aspiradora, saludos desde Mexico!

I can't thank you enough! Thanks to your video, I managed to clean the vacuum motor that was stuck with dust, and now the robot is working. Now, I'm trying to figure out an issue with the lidar sensor that occasionally gives a warning that it stucked.

Vidéo sans aucun intérêt, car il démonte à toute vitesse en cachant les emplacements des vis. Je voulais savoir comment démonter une roue motrice pour la nettoyer, la décoincer, mais je n'ai rien vu. Qui a besoin de savoir comment on demonte "entierement" la machine ?

Thanks for your tutorial very help me

у меня основная щетка не крутится - даже вручную не провернуть. это сгорел мотор?

Show me continuously the message clean the radar and stop to working,maybe you know what I should do? Thank you in advance

Спасибо тебе дорогой. Могу сказать только будьте аккуратнее с шлейфами. У меня один развалился. Предварительно их нужно покачать

thank you. I need to tie the front wheel that is getting loose

Hello .Do you have any information about model of motor used to main brush rpm voltage

Thank you

Hi mine has stopped charging🙃. I Cleaned the contacts this helped a couple of times but no longer. I changed the battery. I put a multimeter on both sets of contacts. On the device I get a .7 someting reading in diode mode and the charger gives 16 sometimes when measuring DC voltage. This is where it gets confusing. At first it would give a reading only while the contacts were up but after I took it apart and cleaned and tweaked a little they now give a reading only when pressed down . Still not charging One thing I haven't tried is popping off the front wheel to see if something is holding it away from being fully seated. Read some where this could contribute to a charging issue. I can't pry it up. Does anyone know how to remove and reinstall?? Or let me know if there is something else to try or an expert to consult. Please and Thank you.

Mine isn't charging. I cleaned the contacts and sensors. the multimeter says that the base is putting out electricity. I swapped in a new battery. would opening it up and cleaning it help. customer service says it's an internal issue but won't say what internal issue.

M7 Robot süpürgemi nasıl kullanabilirim

Hola, después de desmontar el midea M7 no vuelve a encender. Le ha pasado a alguien? Hay algun procedimiento especial de encendido? Gracias de antemano

Производители этого пылесоса стопроцентные идиоты, раз настолько усложнено обычное ТО. Никогда это г.. не куплю и другим не советую.

Thank you very much for the explanation ❤🎉

Подскажите, как чинить пылесборник? Помыла его, только потом прочитала, что нельзя. Теперь выдает ошибку, что поместите пылесборник.

Hello mate, i have this model I get this error WIPE THE CLIFF SENSOR I do, but still the problem remains, it looks like those are damaged, do You know where can i get a replacement?

Hi, a buy one on ebay, but this no drop the watter, do you know how I can do?

I think I won't buy products of these people. They are so very insecure that they make it extremely difficult for even experts to open their machine

Mine says "please clean the lidar", and that it's stuck, when it's clearly not.

Thank you! I also have the stuck wheel problem and still haven't had the chance to work on it. This video is gonna save a lot of time

First thing the wet mode doesn’t work! Even when brand new and after 12 months the base charger burnt out and luckily it doesn’t burn a hole in my carpet but it does burn the vacuum base contact though! Midea Melbourne office refused warranty and told me to send it back to Amazon USA and it ll cost me $200 to mail it back! Useless!!!

Thank you very much for this video. Last month a tried to fix my robot (one wheel wasn't working) and i couldn't open it nor find any video for it. Now thanks to you it's already cleaning my house. Thanks once more!

I have one wheel that does not function and I could not get the cover off (what you did with the wooden tool). This video shows clearly how to remove the cover. Thanks!