That’s sick. Stock MAF? I’m looking at doing the same setup
@Chessermotorsports3 күн бұрын
@@ScrappyDew22 it was, now it has the WHD to ECU Masters harness running an IAT. Tuned on ID1050 injectors.
@jamesfrye63984 күн бұрын
Dont change your OEM pins..you will get brake vibration..i learned this lesson the hard way..
@Chessermotorsports4 күн бұрын
Great info, appreciate the comment.
@moneymovest8 күн бұрын
Im confused so i plan to do this setup snd im wondering what do i need to do for the driveshaft. In all these videos i see nobody talking about it
@Chessermotorsports8 күн бұрын
@@moneymovest you can call driftmotion and tell them what you got trans and diff wise and send them some measurements and theyll send you what you need. Its super simple
@nitrothunder99378 күн бұрын
So just to confirm with the axles and axel stubs you just used the same ones off your is300 diff or are those gt86/brz/frs axles and axle stubs ?
@Chessermotorsports8 күн бұрын
@@nitrothunder9937 yes used IS300 stubs and axles
@scottieunderwood566627 күн бұрын
Sweet. Nice clutch. Great video
@Zero-iz3euАй бұрын
Wait for them to come with a nice gift
@ChessermotorsportsАй бұрын
@@Zero-iz3eu im pickin up what your layin down
@flaco2746Ай бұрын
I bought an auto diff and didn’t do any further research like I should have. Do you know if the auto FRS’s have a 4.10 LSD like the manuals?
@ChessermotorsportsАй бұрын
Im not sure about that at all. Pop the cover off and youll know in 2 seconds
@_ATOYOTA_Ай бұрын
I bought a transmission with this adapter and I don’t have the supply lines! Do you mind sharing the links for the T56 extended bleeder and supply line please thank you!
@ChessermotorsportsАй бұрын
The supply line came with my kit so you should be able to buy it from them and possibly the remote bleeder. I do know you can buy a remote bleeder off Ebay.
@WynterBelcourt-be3in2 ай бұрын
Wynter 😮😲😲😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮😮mom❤🎉😂😊😅
@claydough182 ай бұрын
What broke and what did you fix…
@Chessermotorsports2 ай бұрын
Im embarassed to say but when i filled the transmission from the side i put the wrong plug back in. I had 2 transmission parts on my work bench and it was as simple as that
@jenniferjoseph15602 ай бұрын
My god! I hope there wasn't children living in that squalor! Unfortunately i know people who live in complete filth and just don't care!
@Chessermotorsports2 ай бұрын
It was by far my worst one. Hopefully never again.
@jenniferjoseph15602 ай бұрын
@@Chessermotorsports I'll keep my fingers crossed for you!
@Chessermotorsports2 ай бұрын
The full video is in my page. Its a multiple part video if you want to experience it in full detail
@jenniferjoseph15602 ай бұрын
@@Chessermotorsports thank you! I'll put some gloves on and check it out! Lol
@Chessermotorsports2 ай бұрын
@jenniferjoseph1560 haha, thats too funny. Thank you for the comments and your views.
@bonjourbanks2 ай бұрын
either the photos are out of order or this isn’t real. I’m going with… not real so the landlord has an excuse for the rent to be far too high.
@Chessermotorsports2 ай бұрын
Very much real.
@Chessermotorsports2 ай бұрын
Look up my worst rental on my videos its there
@eddiesnyder43542 ай бұрын
You punish everyone for a dirty tenant is what your saying?
@Chessermotorsports2 ай бұрын
Either that or go bankrupt
@eddiesnyder43542 ай бұрын
@@Chessermotorsports I hope potential renters see your strategy on recouping loss on their dime. Dirty renters are a sad reality of renting, but that doesn't screw everyone because of it. Theyre should be laws against this kinda thing
@Chessermotorsports2 ай бұрын
@eddiesnyder4354 just throwing it out there, where do you think the money for repairs comes from? I mean rentals have to have maintenance, repairs, they are sometimes empty, have to have insurance on them. Landlords factor in repairs and maintenance etc. Hence the rate they charge to rent one of their units. So if they take a $20k loss where does this money come from? Do you think they take out a loan for that money?
@eddiesnyder43542 ай бұрын
@@Chessermotorsports I maintain several rentals and do this work for a living. Security deposits from bad renters and insurance is where the money comes from, not ripping the next person off to recoup your loss. Background checking your renters go a long ways towards preventing this from happening.
@Chessermotorsports2 ай бұрын
@@eddiesnyder4354 who did i rip off? Ive been doing it for 15 years i own 24 properties. I have an extremely low turnover rate. My highest 2br 1bath home is 800 a month. Who and how have i ripped someone off?
@clairestanfield-ui1fg2 ай бұрын
I like the before ones.... more soul that way😈😈😈😈
@brennendovalina55462 ай бұрын
Hey I’m going mine now based on your video, do you not have to push the cylinder into a flush position on these.?
@Chessermotorsports2 ай бұрын
You do but i do it prior to removing the caliper. Its in the video
@ShawnT_1JZ3 ай бұрын
good instructive vid, just a heads up though 99% of Japanese vehicles are metric everything, I can confirm these cars specifically are metric also
@Chessermotorsports3 ай бұрын
Appreciate the feedback
@Sessions13 ай бұрын
Really cool video man, getting ready to mate my kit to my 1j is300 I can’t wait
@Chessermotorsports3 ай бұрын
Hey i appreciate that. 1jz IS300 would be a beast with a CD
@aexiy3 ай бұрын
so did you just throw the kit on and didnt do any tuning whatsoever and its fine? i want to do that with my is300 but idk
@Chessermotorsports3 ай бұрын
Thats exactly what we did. The fuel pump was upgraged as well. We ran like 6psi with zero issue.
@aexiy2 ай бұрын
@@Chessermotorsports nice. im going to do that aswell but with bigger injectors and an afr gauge just incase ;P
@stronecorbett36563 ай бұрын
Did you have to use a slave spacer with the spacer kit? Or just the 3/8 inch thick spacer between the Ar5 and bell housing?
@Chessermotorsports3 ай бұрын
No spacer for the slave
@trxxtinnxr26733 ай бұрын
so no boost cut or fuel issues?
@Chessermotorsports3 ай бұрын
Not at all
@maxskullic98794 ай бұрын
The MUSIC SUCKS and I hate this video for it! When will people learn... Annoying rap/pop/bass will get you NO LIKES! ONLY HATE!
@Chessermotorsports4 ай бұрын
Appreciate the feedback
@Lichinha874 ай бұрын
Do you happen to be still using that wheel or are you by chance looking to sell it? Thank you in advance for a response.
@Chessermotorsports4 ай бұрын
We arent using it. Ill ask my son if he would be interested in selling it.
@Lichinha874 ай бұрын
Okay cool yes please just let me know, thank you
@prasamin4 ай бұрын
Will swapping from stock 3.9 to the FRS/BRZ Y38 with 4.1 affect speedometer reading on the is300?
@Chessermotorsports4 ай бұрын
Im sure it would but with our drift car we dont worry about all that. You could use your phone to see what an accurate speed would be if you needed to know what the difference is.
@Bustedkuhnuckles4 ай бұрын
Hey man I just got a is300 with the same kit already installed I got lucky and got it for 6k it has the autosportsengineering a340 adapter plate and 3uzfe. In my 2001 is300 anyways I’m about to do a trans and throw out bearing as well as a pilot bearing. My question befor I tackle the job is are you able to pull the transmission without pulling motor? I really hope so as that’ll be a lot of extra work. I have a lift to use luckily but just seeing what you have to say about it
@Chessermotorsports4 ай бұрын
Yes absolutely. Shouldnt be a problem at all just drop the driveshaft ,unplug all the sensors, pull the shifter, trans mount, then bellhousing and starter bolts and shes out.
@snazzygma4 ай бұрын
Where is this
@Chessermotorsports4 ай бұрын
Midpond
@donnellthomas23585 ай бұрын
Great vid dude seeing this I don't have to watch any more of your videos
@danny1is_5 ай бұрын
stock ecu?
@Chessermotorsports5 ай бұрын
EMU Black running ID1000
@Chessermotorsports5 ай бұрын
Stock motor for the time being but ive built an engine for it since then and swapped it out and just need to retune and turn it up
@danny1is_5 ай бұрын
@@Chessermotorsports ohh okay, i was wondering because of your other video of you running stock ecu. was it hard? i’m trying to boost my IS on stock ecu for a lil while before i go standalone
@Chessermotorsports5 ай бұрын
@@danny1is_ no just stay down around 6psi on boost
@levihouse53454 ай бұрын
What kit?!
@tasosmazda5 ай бұрын
Sedan cars are like super hot girls whith one gold tooth in front😂😂😂😂
@lysticalz5 ай бұрын
whats your consensus on this clutch? streetable? im thinking of getting it for my setup. im tired of my six puck clutch feeling like an on off switch.
@Chessermotorsports5 ай бұрын
On the IS300 it feels perfect. On my BMW its a little rougher but streetable for sure.
@lysticalz5 ай бұрын
@@Chessermotorsports thanks. I'll give it a shot. My setup doesn't allow me to run a twin disk. Looks very promising!
@Chessermotorsports5 ай бұрын
@@lysticalz i didnt want the twin disk chatter on the 1j so i went with this one in my IS300 and its been great on it couldnt ask for a happy medium that was much better than what it ended up being. I used Spec back in my Honda days when they first cane out and i have had great luck from them.
@stronecorbett36565 ай бұрын
Did you use a remote shifter to bring the shifter back on this?
@Chessermotorsports5 ай бұрын
I did. I ended up finding one of the CPR shifter relocate. I think theres other brands that you can get now that are way better
@stronecorbett36565 ай бұрын
What did you use for the transmission mount?
@Chessermotorsports5 ай бұрын
If i get a chance to get under it i will
@stronecorbett36565 ай бұрын
Good to know the shifter matches up pretty well. What year s14?
@stronecorbett36565 ай бұрын
Did you have to shave off the input shaft at all? I’m. Doing the Ar5 swap with a 2jz on a 95 240sx. And the shifter location was good enough, I was told by drift motion it would be too short?
@Chessermotorsports5 ай бұрын
I didnt but i was able to source the spacer with the kit i found.
@stronecorbett36565 ай бұрын
@@Chessermotorsports how thick is the spacer?
@stronecorbett36565 ай бұрын
@@Chessermotorsports or what company makes it?
@Chessermotorsports5 ай бұрын
@@stronecorbett3656 i dont remember exactly but its 3/4 to 1 inch or so
@Chessermotorsports5 ай бұрын
@@stronecorbett3656 i think the guy went out of business but it was CPR out of Canada
@retta3465 ай бұрын
i dont think I would have walked in without a respirator
@Queen_glitch5 ай бұрын
Honestly, how can somebody do this? I understand some of a few things. But I could never leave a house like that no matter how mad I am at a landlord or anything like that I could never.
@MyKeith3335 ай бұрын
This looks like the house I moved into last year. It is this a mess outside. I've had to call codes because she puts her household trash in her big building instead of taking it 4 miles away from her.
@COCKANDBALLTOURTURE5 ай бұрын
Where are you located and how much would you sell it for
@Chessermotorsports5 ай бұрын
Close to Knoxville TN, its a 2jzge vvti with an AR5 trans custom driveshaft ECU Masters with wiring Specialties jz to s14 harness and lots of other things. Id say id take 8500 or so. Ill have to do some math on what i got in it but somewhere in that range. I got full videos of what it had in this channel.
@S8Faky5 ай бұрын
I want to buy that 😂
@Chessermotorsports5 ай бұрын
Id sell it
@freddygranja51056 ай бұрын
hood aint closing
@nickkingkeo37076 ай бұрын
There's a 2006 Colorado ar5 for sale around my town. Is it the same as yours? I noticed it's a shorter shifter. Would I also need to buy the shifter relocater? I've heard of the solstices ar5 where it's other but I think the one I'm looking at is the same as your.
@nickkingkeo37076 ай бұрын
Longer*
@Chessermotorsports6 ай бұрын
Theres a few variations of these transmissions. I think the main difference on them is the rear trans mount orientation. Youll need to figure out which one youll need for your application. I dont know all the details on which mount style is in what vehicle but i think thatll be your first hurdle.
@waterfall3166 ай бұрын
I hope my IS can sound like that one day
@rowdylexus6 ай бұрын
Sick
@snowboardslider246 ай бұрын
I thought dinos were extinct... L.O.L.
@gatecitywake6 ай бұрын
this is an awesome overview! thank you!
@joshcoughenour80016 ай бұрын
He won't have it long treating it like that I know from experience
@KungFuJordan6 ай бұрын
You have the measurements for your drive shaft??
@Marketingbymasud7 ай бұрын
Hello: Chesser Motorsports I have visited your KZbin channel. The channel is very beautiful. But the channel has some problems. Channel Video has no good SEO and no valuable tags. As a result, your channel SEO score (20), views (79) and Likes (3). So you can increase your channel views and subscribers. If you want. I can help you. Your channel is a problem=
@ShuvoChowdhuryOvi7 ай бұрын
Hello, I visited your KZbin channel and found your content very good. There are some issues with your channel, due to which your videos are not ranking well. Hopefully, the videos will rank well if these problems can be solved.
@dillpickle897 ай бұрын
I think I got my shift arm 281 lined up wrong but this might be it