If you use a 12v battery you have enough room to locate power supply within as well.

I don't have a wifi network but it looks like this board could be used with the app by connecting through Bluetooth as well?

My brother gave my his old 996 a few years back, after mine was stolen from my truck. He bought a new drill from another brand, but has asked for this drill back a time or two. But I've been very impressed with the power and durability and i shall be keeping it, though I do need to take it apart and clean, as well as inspect the bearings. Absolute beefcake of a drill

You saved my life man . Thank you🙏🙏

where can you buy resistors?

I am planning on doing this on my Kodiaq and expected to see the complete grille removed followed by removing the chrome surround on it. I would imagine it would be much quicker to remove the chrome piece with unhindered access to all the fastening clips. As well as this the top cover could likely be secured before offering the complete grille into situ.

Brilliant video thank you! I also unclipped the washable filter and the dirt in there was ridiculous.

Got my craftsman transmission apart, and the drivehaft was completely different. I was a six sided shaft that nothing would fit. Threw it in a vice and broke the chuck loose with a large pipe wrench.

Good job. Thank you.

These are post motor filters only, the dc75 doesn’t have a pre motor filter

Thank you!

Thanks a lot for this. I can use this info if I have to remove the chuck on my Craftsman drill, which is owned by the same company. Tried a local warranty center, and theyt hey gave up. One interesting thing about online customer service with my drill : You deal with an AI program . Somehow, the way I answered the questions caused the program to send a new drill complete with the charger and battery ! This might happen with a Dewalt as well.

Any idea why it will only run for exactly 5mins ggen cuts out...then you have to let go of trigger and repress and it will work again for exactly 5mins and so on and on....will not run for longer than 5 mins.....drill is brand new and other drill does the same????

Great video. Good job and you've saved a wedge of cash doing it yourself. Sorry if i missed it, bit how much was the grille from skoda?

Excellent All working, many thanks

Thanks very much.well talked threw.i took the 4 voltage resistors out,cleaned spirts of salts and re soldered the 4.reconnected and it worked.😊i did not think i would be smart enough to do it,but i did thanks indeed to you.kind regards john.

Hello hey great video. Im wondering if you could help as im having an issue with my dewalt 20v brushless DcD 995 where it wont hammer drill, all the setting work for drilling. I bought and replaced the whole gearbox and chuck but when i put it on hammerdrill mode it still doesnt hammmer only drills in that setting. Would you have any idea what may be the problem ??

Nice walk through thanks. Gave it all a good clean out, and it's back working like new again.

So what’s stopping/why couldn’t you just drill through the old garbage chuck before the spindle, secure the drill in place firmly and tensioning off the spindle/chuck in one piece and then popping a new one in?

I had the black edition of this radio great bit of kit.The whoofer on the bottom blew so upgraded to the mg 007 both great radios

Thanks Super

Perfect instructions, worked with my Topens A5 gate opener. Thanks for the video

Great detail in this video your knowledge is extensive. You didn’t fool me regarding the vide damage to the gear box housing. As an engineer for over forty years it takes a lot to pull the wool you didn’t manage it. lol. Buy yourself some vice jaw protectors, I use hard and soft ones it does help yo stop those ugly hardened jaw in prints that can happen. Good luck with your channel.

Can strip down the cyclone further by removing T8 torx screws

I don't suppose you know the resistance value of the resistors so I can get new ones. The colour bandings are not clear enough to determine the value. Thanks and great video. EDIT. All sorted. I fitted 4 new 4.7 ohm 1 watt resistors.

The barrel seems to stick out about 15mm perhaps 70mm is too big. Having a barrel sticking out does make it more vulnerable to brute force attacks with a pipe wrench / stilsons.

Cool, didn't know these existed, gonna get me a couple. Thanks for the vid..

Brilliant! Thanks😊

I need a video for removal and replacement of the daytime running light on drivers side for a 2019 Santa fe

Great video. Works for dcd999 as well

What you did is a bit pointless.....most of the dust etc goes into the cyclone, so that also needs dismantling to clean.

The problem is a weak spring under the adjusting screw i have replace it with a same length but stronger spring now I can cut wires single handed use the adjuster for different gauge wire 👍

It is so hard.

Really helpful, thanks

Thank you mate!

Kool

You got the 24vdc module, as you need to power from 24v from board. Mine does not have 24v but checked online and there is. 230v module option. The relay to the switch, on the other hand, is a command signal, so no mmattert the current of the board correct?

Crazy eyebrows

Just came across the WAGO 221s in a light fitting in my new house, never seen them before. Excellent tutorial, really clear and concise. Many thanks for posting.

Excellent video! I have a Hyundai Tucson 2016 with the led eyebrow head lamp not working, do you know if the process will be similar to this to fix it?

Great tutorial, I found one in a pile of items left out for inorganic collection here in Auckland so will have a go and see if I can get it up and running again. Many thanks from an other pensioner who hates to see things discarded that could possibly be fixed.

Wit size of resistors did you use.

Thank you !! (Y)

Excellent video and appreciate sharing the part number

Great one. After setting this up, are you still able to use the wireless 433mhz (I suppose) remotes for controlling the gate over and above the mobile apps?

Are they still very very very bassey .

I can’t find anyone to help me repair my Dyson. The battery is charged, filter cleaned but still doesn’t work. A lot of money down the drain. Can anyone tell me where I could find help?

Thank you for the video, I did two similar to this (one for the garage door and another one for the gate) but I don't have the inching mode on smartthings and I had to add a routine for auto-off after 1 second. Now I'm after a device that will give me an indication of the gate's situation. The gate has limit switches and I want to use them for that purpose. All I need is a wifi device that whether the circuit is open or closed. Do you know such a device?

🎉 Very helpful.😊

This thing sucks as a jobsite radio. I work in construction and we had to recharge the batteries after only 3 hours of running time. Talking 18v 6ah brand spanking new batteries. I Switched to an older model and it runs for 2 days. I don't recommend this thing at all, especially for the price they are selling it for.