I hope you cleaned off the block before putting on the base gasket and cylinder as there was old gasket material all over it still when you installed the piston.
@oldjalopygarage728821 күн бұрын
Yup, all good. Thanks for watching.
@tooljunkie6003Ай бұрын
Great video How does the truck run now? Just subscribed
@oldjalopygarage7288Ай бұрын
@@tooljunkie6003 Runs great. Doesn’t run rich anymore. 👍
@OheeeohАй бұрын
Thanks for the video. Sorry for what is probably a dumb question, but are those rockers that you installed stock or aftermarket?
@oldjalopygarage7288Ай бұрын
@@Oheeeoh They are the stock rockers. Thanks for watching.
@CuateBro3 ай бұрын
Polaris500 2004
@richardsoule2785 ай бұрын
Most excellent video,- much appreciated, how did you get that head so clean,? and milled?
@oldjalopygarage72884 ай бұрын
Took it to a shop to have it bored.
@richardsoule2785 ай бұрын
great job.
@FarmerSteveO6 ай бұрын
Thanks for the well made video and reference. I am right in the middle of the head install in our 2003 Sportsman 500. What a crazy torque sequence!
@oldjalopygarage72884 ай бұрын
Yup found it very strange.
@jeremyhamilton198010 ай бұрын
Just curious if ring 1 and 2 are any different or is there a top and bottom to the rings
@oldjalopygarage72889 ай бұрын
Rings 1 and 2 were marked and the markings face up.
@buildurtruckurway911811 ай бұрын
Why did you stop making videos? You seem to enjoy it.
@oldjalopygarage728811 ай бұрын
I do enjoy making the videos and will make more soon. I moved to a new place and don’t have everything set up yet. The move was overwhelming.
@pablobracho665311 ай бұрын
A ese auto chevelle malibu1973 yo le colocará una transmisión 400 de 12velocidades sistema de guaya un motor 573carburado con 1 turbo hibrido de formula 1 pequeños le cambiaria el frontar por el del malibu laguna s3 que es mas corto y los parachoques delantero y tracero lo recortaria y se los pusieron mas pegado a la carrocería
@eckateckat3449 Жыл бұрын
why you have the vacuum advance hooked on to the manifold vacuum port? when I do this on my edelbrock 1406 the car idles up and down rpm and hard gear shifting
@oldjalopygarage7288 Жыл бұрын
For some unknown reason, mine runs better off manifold vacuum. Tried ported vacuum and it ran like crap.
@godsdozer Жыл бұрын
My 2009 has a frame bracket right over the top of the head, cant get to the top two head bolts. . Instead of removing engine, Ill just cut the fram bracket off and re weld after top end rebuild. UGH great engineering by Polaris.
@jaywinters2483 Жыл бұрын
Fantastic video for the following reasons: 1. not ruined by music or a wide angle lense, good teaching, good views. Thank you.
@wishiwantyou Жыл бұрын
The torque specs was useful thank you on that
@davidmiller4816 Жыл бұрын
What brand cam shaft did you use
@oldjalopygarage7288 Жыл бұрын
Didn’t change camshaft. It was ok.
@jaredmcdonald7288 Жыл бұрын
Thank you for these videos. I also have a 96 that I'm rebuilding this moment and your info is very useful.
@jaysta86tube Жыл бұрын
Is this thing a 2 stroke? It sounds like a 4 stroke
@jaywinters2483 Жыл бұрын
It's a 3 stroke, silly.
@oldjalopygarage7288 Жыл бұрын
4 stroke
@pablobracho6653 Жыл бұрын
Le falta velocidad y desplazamiento a ese chevelle...
@dimmytihon Жыл бұрын
Less than helpful
@joshpotter46332 жыл бұрын
Where did you get the Camshaft kit?
@joshpotter46332 жыл бұрын
also did you notice a large difference in speed after you replaced it?
@oldjalopygarage72882 жыл бұрын
Didn’t replace the camshaft. Replaced the piston and had the cylinder bored.
@delvej2 жыл бұрын
Thanks for the great video. Tackling this job tomorrow on a 99 sportsman 500 and this will help lots ! 👍🏻
@lownds_82492 жыл бұрын
What’s the wheel and tire spec combo? Especially on the rear I just picked up a 73 and was going to go 10” wide, maybe 4-5” backspace?
@oldjalopygarage72882 жыл бұрын
Tires on back are P285/60D15 and I think the backspace is 5". Not positive, was quite a while ago!
@lownds_82492 жыл бұрын
@@oldjalopygarage7288 right on I really appreciate your reply. Trying to snag up a ‘73 right now and I want to fill the rear wheel wells up if it needs new tires anyway might as well order a wider black ralley for the back and save tire money. Did you get rid of that one?
@oldjalopygarage72882 жыл бұрын
@@lownds_8249 My son has it now so still in the family.😁
@lownds_82492 жыл бұрын
@@oldjalopygarage7288 awesome that makes me happy 😃
@SofaKingSkilled2 жыл бұрын
We didn’t get to hear it run…
@oldjalopygarage72882 жыл бұрын
Running in this vid. kzbin.info/www/bejne/qaXWkGafbJWWiqs
@timpierce58252 жыл бұрын
I’m doing a head gasket on a 96 Magnum so your videos are extremely helpful. One question…before starting it for the first time, did you give it an oil change or did you let it run for a bit, then change it?
@oldjalopygarage72882 жыл бұрын
Fresh oil and filter on first start. Some antifreeze got into the crankcase when the head gasket blew. So oil kept getting milky. Changed the oil a few times after running until oil wasn’t milky anymore.
@josesaucedo76382 жыл бұрын
I would recommend next time when changing a cam shaft to when ever you take the 3 bolts off the timing sprocket to tie something up to it so you don’t haft to adjust you timing chain
@atonyrodify3 жыл бұрын
Hello Great video!!!!!I have a question about the ring gap since you had the jug machined was that the standard ring gap?Thanks for you time and video
@oldjalopygarage72883 жыл бұрын
Oversize piston and rings. The place that machined the jug had it figured out. The ring gap is the spec that was given in the install instructions that came with the new piston and rings. Thanks for watching.
@jaysta86tube Жыл бұрын
I need to do this on my 2 stroke 400 but i don't know where to start. Do I order the piston kit 1st then find a machine shop to machine my jug?
@oldjalopygarage7288 Жыл бұрын
@@jaysta86tubeThe place that machined the cylinder supplied the piston and rings.