Update video?

What’s your rig details

Flossing guide service

That's definitely not fly fishing FYI, that's michigans cheater way of snagging

Nice video, well done!

Nice frend i enjoy your vide very Intristing

Good job guys..

NEW KZbinr here just subscribed

I am forom Indonesia your chanel very nice, nice to meet you , l habe youtube chanel youtube too abiut fishing (ADD fishing Official) you can cek it, so my i have your whatsapp contak for sharing 9:41

Wow! Nice job!

💞Wow🧡🤍🤍🤍🤍🤍🤍🧡🤍

Hey I believe your fuel lines are cheap lines and can't take the suction the motor needs better fuel lines yours are collapsing

Nice video and fish man. Jerk bait doing damage. I just subscribed to your channel. Good luck and Tight lines

You need chance weights or springs on that chinese primary clutch. That should fix your problems on that part.

what are you using for your drive and driven clutch, which kit is that.

самоход довольно опасно с вариатором, но буксировщик прикольный, респект.

Make sure you have the belt the right way!. The belt goes one way, flat side towards the motor. Taper side of the belt facing outward

Carb iced up?

Check which way your belt sits. It shouldn't move at idle

you probably dont want to spend money for youtube but here is one of my recommendations maybe get a gimble

i think the main reason for that crash was the fact you wasn't carrying enough speed for the jumps and cased most of them, therefor causing instability and sending you sideways on the last jump you hit. overall great video keep up the good content 😁

Great build! Here's a suggestion for you...if you shorten the hitch you will plow alot less snow and the sled ride better. You want to space the hitch lenghth so that when you are in the sled comfortably holding the handle bars, your feet are in the middle of the sled, or slighlty toward the back. Standing in toward the front of the sled, your weight is pushing down directly at the front and pushes the nose of the sled down. If you have your feet in the middle, or slightly toward the back, the nose of the sled rides up better and you won't get so much snow piling up and pushing into the sled....and you'll even increase gas mileage and horsepower a little more. But great looking build!

You'll always have to start a Predator with the choke on, even when it's warm. When your belt breaks in,(after you put it on right) your sled will probably stop walking when it's idling. Nice build btw.

Fix the clutch bud. Shouldn’t roll like that. Belt might be backwards which would make it do that too.

Gotta adjust that idle and clutch before ya run someone over lol

Oil sensor disconnect it

Finally an unboxing video for the bundle, thanks!

Belts on wrong. 🤓The belt has an angled side and a flat up and down side. Angled side goes on the outside, then the belt won't engage at idle and drive away. Great build 🏆👍

What kind of sled did you use as a donor?

Having to stand right at the front of the sled causes it to push way too much snow.

Wow brother this thing is awesome!! It is way better than Taryl's. I am going to share this with my friends so hopefully you get more views and subs. Where are you located?

To firm up the steering, mount the bars directly to the folding part. You're loosing input due to flex. Looks great

If you extend the wires to retch to the Handel bars move the starter switch to the Handel bars it make it easy to start for the choke fine a old mower take the throttle cable assembly and use it for your choke

Adjust that clutch setup.. that's not supposed to be like that at all lol and if you lock the handle bars from going down you can tilt the machine to steer way easier.

if you look at the comet clutch drive the belt it needs to be turned around the belt has a flat side and the other side is tapered. The flat side of the belt needs to be toward the motor and you will be able to idle without it wanting to go.

This is awesome, great job on your build. 🎉

I put a predator motor on a roto tiller. I had troubles with it dying for no reason when tilling in rough ground. It would always start back up after a minute or two. While I never "officially" figured it out I always felt like it was being caused by the low oil shut down from the tiller bouncing in rough ground. Especially when breaking new sod. The video made it look like a smooth ride but I've got to assume it was rougher than it looked going through those fields with that. Regardless, looks like fun! Good job!

Looks like your clutch might need shortened. it does not have enough slack to start with out pulling you. It should have to have some rpms to engage.

SO HOW DOES THIS TURN OUT!!!

God I never thought I’d see a man so sexy on KZbin😍😍

Nice vid

Can't wait for the coyote hunt

Awesome video!

Nice quality surprised you don’t have as much popularity plus I’m the new sub :) from Michigan 🤘

Nice job getting through the baits. I agree about the lipless and frog. Those are the two I like the most out of that bunch as well. tight lines from Rick