Nice

Thank you good man! I told my dad we could probably 90 degree it to get the big roller in the track but he wouldn't listen until I pulled the proof out here. Cheers!

It works great!! Just got done pulling 4 huge bushes in just 2 hours (was HOT today so we took several breaks😂) that would’ve probably taken days to remove any other way and didn’t disturb the foundation or the surrounding vegetation. Genius use of a tool not meant for this type of job! I love when people figure out ways to hack their life this way! Brilliant!

Some other shrubs and small trees were tougher and when they broke loose really flew up. Always wear a face shield.

what was the weight rating on that hoist ? 1 ton, 2 ton ?

Concise and to the point. I used dental floss instead of sewing thread and it worked great. Thank you for the help.

Thank you for uploading this. such a simple yet effective tutorial! youre awesome sir!

i tried this and i can see the progress regarding the removal of my tag. However, there's a wound around the hair i put in the tag. is this normal? it is kinda painful and bleeds sometimes so im scared

i had one of those a few yrs,back.had it pumping water.im 86 now and still like the old engines at the shows.cranking days are gone.

Thank you for this video, it is helping me build my truck. Hope you still drive yours!

#단독) #윤석열 검사공화국이 저지른 또다른 범죄! 의사면허취소 확정판결도 막은 검찰!

This was 1996.

OK, its been awhile since this clip... But, do you remember if that was a '53 or '54 car? Because the 232 ci, was like the earliest V8 from Studebaker... And, do you still own it? Best regards...

Maddie watched it this morning and enjoyed watching you work

I have a similar Nove, possibly a little older. I appreciate the video. Would you mind measuring a few things for me, like the muffler dimensions, the size of the oiler and the grease cup diameter?

The instructions say to assemble it upside down. Yes, it's not a fun task, but it can be done. Tip: leave it sit in the hot sun, and that makes it more pliable. Just did mine on my 58 Apache, love it!

For anyone watching this video, one of the easiest ways to start one of these engines is to give it a shot of starting fluid in the carburetor and it will fire and if it has fuel and it’s ready to go it will run.

Wow! That is a big job! I replaced the passenger window in my first car a few times. I don't think I ever got it right. Lol!

This video is better than most c10 instructions because it is most like my 67 G10 van. I see you got a totally new vent window Assy. Don’t think it’s available for the van so I am fighting to reseal it. Pita. Your explanation of the sequence will help on reassembly. My main window fell out of the track, that’s what got me started in the first place.

This is great. Super straight forward and simple instructions. Saved for when my windows come in for my project 66

Nice video. This will help with my 57 Chevy install. 😊 thanks

Thank you very much! Single mom here and as I was cleaning a very full lint tray, I also somehow took off the piece behind it and dropped the two sensor wires beyond my reach at 10:30 at night! I don't have one of those special screw drivers, but I'll figure it out! The block idea was genius! 😘

Will be awkward to install/remove when car is close to wall?

I was struggling to find a good video but I was immediately able to tie it after watching this one thank you so much

I'll check with my dealer about a recall I never heard about. Thanks.

tag, you’re it

Thanks dad

Thank you so much for this.

Great video. Instead of the rubber tape to hold the glass in the channel I used windshield urethane. I also pinch the channel so it doesn't catch on the new wiper whiskers.

fixing to give this a try.

You're good man, I can tell. Thank you for that tutorial, sir!

Very good video and really nice truck. It is nice not to have music playing in the background 😁really nice truck you did a nice job restoring it and just subscribed to your channel I have a c10 1 ton dump truck ive been working on that was my dads I'm replacing the window rollers its aggravating working in such a close space you got to have patience and I can see you have plenty My dad always told me when you mess with glass go easy especially if it's old glass And your calm voice you remind me of him

When using the wire to retain spring compression, only one is needed.

You must have worked in a gm plant.

My 65 chevy G10 van windows wint stay in the track down inside the door. Afraid to take it apart more than I did. Seeing how no one makes spare parts for these. I had to have a windshield and side window cut and it was not cheap.

Being that those dollies are heavy defeats the purpose.

That’s really neat!

Thnks sir m ny try kia 100 percent result mila

i found dental flos works great

CLOVE HITCH Thanks for sharing your demonstration of tying a Clove Hitch knot. https ://www .animatedknots .com /clove-hitch-knot-half-hitches Clove Hitch - Half Hitches [Video] Binding: if you make the knot secure by stacking on additional Half Hitches, i.e., multiple clove hitches, then you are inviting a major strain to cause the earlier turns to bind tightly and become impossible to untie. https ://www .animatedknots .com /clove-hitch-knot-using-loops Clove Hitch - Loops [Video]

Is now the time this gets viral??

I subscribed immediately , thanks for your demonstration , you are a great teacher

Thanks so much, have tried several times to tie me but find it difficult but with your demonstration that I just watched just now I was able to tie two 😀, and have got crushed garlic that am going to apply before going to bed tonight

Thank you for this !

It was amazing

Thank you. Great tutorial.

Thanks great video I appreciate it!

Thank you, I was able to tie one off on my armpit, alone. The angle was difficult, and I had to used teeth and tap to hold the ends, but I got it. Hopefully it falls off without issue!

THANK YOU!

Can you do a video on land deed?