Just bought some from official website, registered genuine ok but only has 1 screw and 1 plastic cap other side so?

I’m opening my ghd that has never had repairs and it has a mark line on the same place you recommended and is filled with white powder remnants I have a feeling somebody used the straightener to smuggle drugs.

Brill video! Thanks I followed it stage by stage and job done! Thanks

my thermal fuse is blown and heaters both measure 68 ohms. what do you suppose? both elements need replacing and thermal fuse?

thanks for sharing. very clear instructions wonderful

Hi Gary, Great to find your website and service. I had contacted GHD for repair service, to be offered 10% off a new one instead!! And wouldn't send me any info regarding a fix. Very annoying how these companies aren't forced to have a repair service with how the world is supposed to have gone so "green". Instead opting to try sell the latest model instead. I've replaced the thermal fuse but have broken the small clip. I've to order a thermistor from your site anyway (only one side is now heating up, (too hot also). Is this clip critical to replace also or would I get away without. Many thanks, Mike

Hi...thanks for the video...can the 2 wires go on any side. Or is it a specific wire for the left and specific on the right?

Great no nonsense video thank you!

hi Great video,I have a ghd 4.2b type 2 does not turn on,I have controlled the r8 resistors and r11 is true ok,I have also control the 2 plates a gives me value 70 ohm and the other 62 ohm toltecdal PCB you can dare suggestions thanks

My friend offered to fix my straighteners but they returned them saying that my GHDs were unfixable. I was going to dump them down the tip but thought nothing lost if I have a go myself. I found your video and now they are working just fine. Thanks for a clear instruction video. Absolutely brilliant!!!!

Thank you, thank you, thank you!!! After a year of not having a GHD I decided to order the parts and try to fix it myself before buying a new one. Within 15 minutes it was done, thanks to your tutorial. Very easy to follow. You're a wiz 👍

i replaced the thermal fuse on my partners ghds but only the main plate is heating up/smoking but turned it off before fuse failed... do you think the secondary plate has failed?

I want link sperpat catokan ghd gold

nice, clear demonstration. thank you.

Tea has got in my ghd glide wat should I do ?

Tea has got on my ghd glide ...will I need to open it up to clean it ?

Thank you. Your clip is clear, concise and easy to follow. In short you saved us a few bob. Thanks again

Hi, I've tested both R8 and R11. R8 is showing as 1 and R11 is showing as 51, am I right in assuming that the R8 resistor has bust? Thanks

hi, i have GHD 5.0, have replaced thermal fuse because it was broken, but now when turn on i listen beep and only one resistor is warm, the resistor near termistor is cool. What i can check ?

Ta pal, r lass loves me again.

Top man! I thought it was the switch at first, she will be pleased. They packed in as she was half way through her hair, all I could do is laugh.

My MK5 is going off just 2 seconds after turning on...did you came across this problem? kzbin.info/www/bejne/nHnOloGkn9mco7c

Excellent tutorial. Made the job simple. Thanks 👍

Don't put the straighteners between your legs you will stab yourself. Put them in a clamp. I when through me finger when the screwdriver slipped. Luckily I did not go through my leg.

Danke für die Anleitung! Hat super geklappt. Glätteisen funktioniert wieder !

Thank you so much. :-)

where do I buy the new socket

Worked a treat - thanks!

Hi can you please help me ... I have a ghd Mk5 model I replaced the thermal fuse and it's still not switching on I tested the resistors R8 and R11 they were fine i tested the plates they were fine i tested the main cable that's fine so i can't see what else can be the problem .. Will you please be so kind to give me advice at what else might be the cause cos now currently it's not switching on no beeping sound nothing I checked everything that are usually the problems PLEASE HELP ME.Thank you for your videos 😄🥰

Hi can you please help me ... I have a ghd Mk5 model I replaced the thermal fuse and it's still not switching on I tested the resistors R8 and R11 they were fine i tested the plates they were fine i tested the main cable that's fine so i can't see what else can be the problem .. Will you please be so kind to give me advice at what else might be the cause cos now currently it's not switching on no beeping sound nothing I checked everything that are usually the problems PLEASE HELP ME.Thank you for your videos 😄🥰

how to test if cable broke on ghd

I’ve just bought a pair of ged straighteners and they don’t have a temperature control on them are they fake please (that’s ghd)

Thanks just repaired 5.0 model with your guide very informative and they are back working like a charm, great job ..keeps the Mrs happy thumbs up!! P.S the fuse I used was the same size as ghd fuse off amazon less than a fiver, Thanks again!

I have mine at it comes with R8 and R11 with 510 Ohms (as colors sch.). The PCB seems a bit different. Could be possible? The model is 4.2B Jamella Limited 150W

Exactly what I needed, thanks!

Great help. Thank you so much. However, I now have a spin and curl iron and the cylinder is not rotating. Any idea as to how this can be taken apart and fixed please?

what brand / type thermal grease do you use?

Excellent tutorial

Hab zwar kein Glätteisen, das Video finde ich aber trotzdem klasse!

Hi, where do you get the parts from?

if you try to register the product number on the halogram with a fake would it still work?

I’ve fixed my straighteners but when I put it all together, but the two irons are sat two close together almost to the point where I can’t get my finger in to switch the iron on, any ideas what I can do? I’ve screwed everything in g down so I can’t think of why it’s not sitting apart enough

If one of a ptc thermistor's plates come off how can i fix it or can it be fixed. It's out of a 30 dollar set of boot dryers.

Спасибо Вам.Коротко,ясно и понятно.Dankeschön

Hey do you have a video on a fake ghd platinum??

Hi i just have l questions, l already broke the clip wchich holds the termar fuse what can l do in this case? Can l leave it like this? Or attached with glue or something else?

Hi...I need price on the GHD cable

Excellent! Thanks very much! Saved a few quid :)

Wouldn’t adding a bit of thermal paste to the back of the thermistor work?

What temperature are these straighteners meant to get to? 230 or 185?