Пікірлер
@MalikAlmaqtri
@MalikAlmaqtri 6 күн бұрын
Bad work
@12т-д5п
@12т-д5п Ай бұрын
Hi Great job!!! Please tell me how much your services for a major overhaul of such a cat3516 engine cost?
@afonsodialamikua8107
@afonsodialamikua8107 3 ай бұрын
Gap this motor please.
@jeremiahtembo5549
@jeremiahtembo5549 4 ай бұрын
When the tubes in the cooler gets damaged , oil because of high pressure than coolant, gets into the water
@electro-progghazi680
@electro-progghazi680 5 ай бұрын
👍
@chetachiharrison3266
@chetachiharrison3266 5 ай бұрын
Good job
@egwuatuuwalaka6641
@egwuatuuwalaka6641 6 ай бұрын
Please which pin is positive and negative on the ecm supply.
@KelaniMonsuru
@KelaniMonsuru 6 ай бұрын
What can happen if light did not come on the nursle
@utilisenergyservices3345
@utilisenergyservices3345 8 ай бұрын
Valve seating not machinery 😅
@utilisenergyservices3345
@utilisenergyservices3345 8 ай бұрын
Amateurs 😂😅😅😅😂😊
@utilisenergyservices3345
@utilisenergyservices3345 8 ай бұрын
Guide insurers from the wrong side😢
@95boostedkoki
@95boostedkoki 9 ай бұрын
I just replaced my oil cooler, what a mess.
@Thiago_Eletricista
@Thiago_Eletricista 10 ай бұрын
www.youtube.com/@thiagosantos2541
@mdrashidhussain9082
@mdrashidhussain9082 11 ай бұрын
You have ecm for sale
@juancamilolugocalderon8848
@juancamilolugocalderon8848 11 ай бұрын
A que pines los conectaste de lado y lado porfavor dime gracias
@juancamilolugocalderon8848
@juancamilolugocalderon8848 11 ай бұрын
Donde la conectaste a que pines porfavor indícame
@bossjerometechshow
@bossjerometechshow Жыл бұрын
how much the good pressure bro?
@Clear021
@Clear021 Жыл бұрын
nice to meet you, which country are you from, I'm from Indonesia, there's a problem on the caterpillar G3561B gas engine panel, with a power loss indicator
@ingrikelmer_8555
@ingrikelmer_8555 Жыл бұрын
oooow
@AG_Marine_Shooter
@AG_Marine_Shooter Жыл бұрын
What is the reason?
@ezechukwugeorge8479
@ezechukwugeorge8479 Жыл бұрын
Please I need flashing software
@wasifali4983
@wasifali4983 Жыл бұрын
How did you do
@astinaastin7494
@astinaastin7494 Жыл бұрын
Ada jual engine excavator cat320gc mas
@abhiram5468
@abhiram5468 Жыл бұрын
What is the cause of this problem?
@boraxguy8302
@boraxguy8302 11 ай бұрын
Failed engine oil cooler, internally breaks and allows coolant and oil to mix
@mdichhahaqali8455
@mdichhahaqali8455 Жыл бұрын
খুব সুন্দর একটা ভিডিও
@dentheanal4388
@dentheanal4388 Жыл бұрын
do you have telegram or whatsapp?
@dentheanal4388
@dentheanal4388 Жыл бұрын
Hello friend
@normanlau6537
@normanlau6537 Жыл бұрын
Please use ear protection.
@wily6018
@wily6018 Жыл бұрын
y el factory passworld
@texpowerengineers3641
@texpowerengineers3641 2 жыл бұрын
bg te music lagaile ao valo hoto.. fast forward saound ta ono birokti lagche.
@AdeptApe
@AdeptApe 2 жыл бұрын
This is my video, why the heck is it on your channel and monetized? Please remove it from your channel.
@marineenginesolutiontask2659
@marineenginesolutiontask2659 2 жыл бұрын
Hello sir, Yes this is your videos I take from your chanel just learning . But my channel no have monetizated. My chanel is too small not available to monetization. If you want I remove
@philliphall5198
@philliphall5198 2 жыл бұрын
I’m not being a smart ass but drill bit in gears will tell you yes or no Try it. Old school grap like me
@philliphall5198
@philliphall5198 2 жыл бұрын
Dam I miss doing it just because I hit 70
@haiderk3246
@haiderk3246 2 жыл бұрын
Thanks sir 🙏
@oldcatmech
@oldcatmech 2 жыл бұрын
If the cyl. block and or cyl. head has been surfaced the factory hole alignment hole can be off! Took a idler gear and cut it so I could go through the slotted holes I made in the gear so I could snug the retaining bolts a little then pry the gear and idler shaft over tell I got the alignment of the timing make and have the right backlash! Cat had us send them a picture of the gear we made and came out with one that is hour glass shaped removing some of the teeth, so you could get to the bolts to adjust them!
@mdichhahaqali8455
@mdichhahaqali8455 2 жыл бұрын
Good job
@bobocaterpillar3697
@bobocaterpillar3697 2 жыл бұрын
i use a mag base dial indicator on the cam gear. hasn't failed me yet.
@mohammadsaifulalam4643
@mohammadsaifulalam4643 2 жыл бұрын
Good luck
@syaifudinzuhri5226
@syaifudinzuhri5226 2 жыл бұрын
top markotop
@abdullahalasif7858
@abdullahalasif7858 2 жыл бұрын
Apnr kace ki EISM pawa jabe?
@marineenginesolutiontask2659
@marineenginesolutiontask2659 2 жыл бұрын
Yes dear available! 01315482040 my WhatsApp number.
@kapilbiswas6228
@kapilbiswas6228 2 жыл бұрын
Nice video
@marineenginesolutiontask2659
@marineenginesolutiontask2659 2 жыл бұрын
Thanks
@abdullakhan267
@abdullakhan267 3 жыл бұрын
Thanks
@BibleStoriesandBeyond
@BibleStoriesandBeyond 3 жыл бұрын
Nice 👍
@marineenginesolutiontask2659
@marineenginesolutiontask2659 3 жыл бұрын
thanks for watching
@zeeshan_engineering_services
@zeeshan_engineering_services 3 жыл бұрын
By the way I always freeze or cold down valve guides and inserts in all models of 3500 A B and C series diesel and natural gas engines for optimum machining results and engine performance 🇵🇰☺️🇺🇲😉
@zeeshan_engineering_services
@zeeshan_engineering_services 3 жыл бұрын
Hmmm we use Caterpillar 6I-4609 Body as Piston in 4EK prefix CAT G3516 engines frequently 🇵🇰☺️🇺🇲😉
@jefersonsouza123
@jefersonsouza123 3 жыл бұрын
Hi there.. Can you tell how to do self test using 7x1713 cable? As you may know this module can test itself..
@marineenginesolutiontask2659
@marineenginesolutiontask2659 3 жыл бұрын
u can use only 7X1414 cable for self test.
@jefersonsouza123
@jefersonsouza123 3 жыл бұрын
@@marineenginesolutiontask2659Thans for your reply.. this cable pn its only for diagnose propose.. 7x1713 suppose to include diagnose and self test for all sensora inputs.. this way no error will be detected during module test..
@moinnaqvi1064
@moinnaqvi1064 3 жыл бұрын
Where this location
@marineenginesolutiontask2659
@marineenginesolutiontask2659 3 жыл бұрын
Bangladesh
@genaromuzquizjr8125
@genaromuzquizjr8125 3 жыл бұрын
Hi quick question, how many o rings go behind the cam gear ?
@dannysedillos8799
@dannysedillos8799 3 жыл бұрын
2 - one on the OD of the thrust and one between the thrust and the head
@mdfaridulislam4650
@mdfaridulislam4650 3 жыл бұрын
nice
@marineenginesolutiontask2659
@marineenginesolutiontask2659 3 жыл бұрын
thank you so much