I bought the GBH 18V-26 in a one-off sale for about 150 EUR. Best tool I ever bought for the money. Sufficient power for most applications, reasonable weight, and with the GDE 18V-16 additional dust extractor, it's absolutely perfect. Also, I personally think that the non-F version is better. You can buy all sorts of non-percussion drills and use them normally, and also, longevity-wise, the quick-change mechanism will suffer mechanically long term. I used to have the GBH 240 F and never used the "normal" chuck - not a single time. For common drilling, pretty much everyone has some kind of other solution, typically a smaller and lighter 18V or 12V drill/driver. This was never meant to be a universal drill to cover a wide range of applications, not to mention driving screws etc.

Thank you for your efforts I really got the information ♥️♥️♥️

I watched the video I bought the table saw. 😂

💩💩💩

I have major problems finding a router table base plate for this router. 62 x 62 mm hole distance. Any idea?

Очень странно, в комплекте и в инструкции по сборке почему то отсутствует нижняя опора для средней части этого приспособления, из за этого этот инструмент не может правильно работать.

you know why the long woodscrews don't work , cause they torsion too much absorbing the energy of the impact , then , rebound .🎉 , nice that i just figured it out 😂

Looks fun.

Rodriguez Scott Lee Angela Williams Margaret

Praij kitana

Por gentileza, qdo chega a GDX 220?

Dimana untuk yang sama ada pengaturan nya

Link pemesanan nya om

Untuk link nya pembelian nya om

Hola buenas Noches soy Miguel de Bunos Aires Argentina....Muy Buen vídeo😮😮 Creo que es lo Que me Hace Falta pero.... Tengo Auto.. esta Herramienta saca las Tuercas de las Ruedas ? Que es .. también muy importante para mi... ya que Trabajo en la calle .. y cada tanto tengo Q cambiar el neumático 🛞 Por pinchar .. Si sirve para eso... Me vendria de Diez ...😂😂😂 Por si me podrías contestra estaría mas Q agradecido 🎉🎉🎉 Hasta pronto 😊😊😊

You don't need to install 10 lag bolts ,no one does that one after the other, Not even when building decking

Jsi dement

dewalt performans olarak güzel kalite olarak vasat bir marka ..

sıkı bir dewalt hayranı olarak söylüyorum 3 yıl sonra kronik şalter ve kafa arızası veren bir makineye bu kadar para vermenize gerek yok ...bpsch ürünlerinin kalitesi devaltı geçti :( 3 yıl önce dcs331 ve dcf887 modelini almış biri olarark söylürum paranıza yazık olur....sadece akülü darbeli matkap modelinde sıkıntı yaşamadım onuda pek kullanmıyorum zaten

Brushless Motor?

Falsch zusammengebaut

can I still use the blade guard when I'm cutting at a 45 degrees angle?

Una demostración real. Eso si que importa

So is it the longer the screw the higher speed you set it on

woo hoo I just bought one of these after fighting to drill pilot holes in two by four wood with my basic drill - getting it tomorrow and wow looks good - thanks for the video!

Thanks for this! Good to see a review which shows low end speed applications, as used for knock down fittings, for example. I like the idea of an impact drill that can pilot holes in wood at high speed, and deal with finer slower speed applications. Time to upgrade!

How do you manage to keep the bit attached to the drill ? I just received mine today and I was very disapointed to see the drill is not magnetic :(

Can it use dado saw blades??

Cool movie. Everything shown in a nutshell. I was interested in checking out the gentle motor start. Thanks!

Thanks for making this video

Hi, why does the bit holder swing a lot with the Dewalt DCF887N screwdriver?

alguem sabe me dizer pq essa parafusadeira 887 algumas vem escrito 18v e outra 20v max

Used it to demo a large Bedford stone fireplace that had a thousand bricks inside, and it did the job well and is still working kzbin.infoUgkxqqoaX03nrziKwF7Bjjcc71YzLEleMvOS . It took abuse above and beyond what it would endure in a shop environment (grit and dust, watery compressed air from a portable compressor, a few drops from roof height) and still works great. I kept it oiled and drained the compressor often but that's all the "care" it received, the rest was just hard relentless chiseling for a few days (we cleaned the mortar off the stones and bricks too) and it performed admirably. For less than $50 it was a great bargain. Electric demo hammers start at around $200 and the ones at that price point have mixed reviews; a rental of a contractor-grade unit locally was over $100/day and I couldn't get the job done in less than 3 days minimum (occupied residence so had to be careful and clean up as I went) so a relatively inexpensive air chisel turned out to be the perfect solution.I wrote a longer review about this tool before, with pictures and everything but Amazon wouldn't publish it for some vague, computer-issued reason. But take my word for it, this was a massive, 2-flued/two story (basement and ground floor and 6' above the roof) fireplace and it generated an incredible amount of rubble and this chisel did the whole demo, I didn't swing a hammer once.

I purchased a used one as the piece is a bit pricey, but the machine kzbin.infoUgkxG6fbm3cHBd7CNTjk5D-dwYe9c9tCB9ZN has surpassed my expectations. We sand small parts by hand often, sized around 1"x1/2," and specifically look for a piece that's designed to be vertical. The motor has plenty of torque and great speed settings. The only inconvenience I had is that the disk measures 5" where we trim 6" stick-and-sand disks down easily by mounting it then cutting with a box cutter.

gdx 210c is newest model.

Upgraded from an older 18v kit. kzbin.infoUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv I independently chose the drill and impact tool, before I came across the kit.I like the 3 speed impact gun. It seems more powerful than my older one, and it can be set to be really gentle. The drill is more appropriately sized for my use. I used to have a hammer drill, but I did not like that it was so big and it was not a great hammer drill. I rather have a smaller drill like this, and then get a corded hammer drill for the odd case I need that.

Small but useful

You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzbin.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.

Much better than the assembly instruction on the manual. DeWalt always makes the manual hard to read. (Like diagrams separate from the texts.)

Just brought one thanks for the video

Nice, simple, no fluff or self-agrandizing. Thanks.

Just bought one!

the only important part of the video, how fast i drills a deep hole you speed up. Wtf. Fake Video dont use this as buying decision help. :)

So this is unboxing and first cut, not review, at least that’s what I got it

Brilliant video... no drinking coffee, no vlog on the way to the shop to collect the saw, no dog playing with the packaging. Perfect 👌

Why do you have it on setting 4 you should have it on setting 6 to get the highest amount of speed and torque.

Built it wrong..😅 the middle should be inline so that the bars are all the same so you can cut smaller logs.

I did it too. This is what I used Woodglut designs for

The least amount of vibration in any orbital sander I have ever used.The dust collection bag is easy to remove and put back on-a turn to the right to remove,a turn to the left to put back on.I recommend this orbital sander to anyone whether pro or the average diy’er.

Idióta....