Jesus Christ. I see what your issue is. Pull your lizard out of your sisters ass for a minuet and clean your equipment. How can you run around with filthy gear like that then be bewildered when things don't function correctly, for fucks sake.

Isn't the "waterline" created from the boat sitting (not moving) for long periods of time? What I got from your video is, leveling the transducer parallel to the water when you're on plane? I'm also going to try that. Currently, the dealer set it up to be inline with the bottom of the boat and a little below the water line, which is how Hummingbird mentions in their installation manual. But when on plane, I either lose my Depth reading & Sonor Graph or my depth readings go way out of whack by 100ft plus. I tihnk you gave me a good idea to overcome this, I'm going to try it and see. It's just so frustrating to purchase a piece of electronics, nearly 4 thousand dollars, and it can't even function as needed.

thanks for the video. those carbs are noted for gumming when they set for awhile. I always add marvel mystery oil to my fuel and it keeps them clean.....cheaper than sea foam.

My friend I’m sorry for my english, next time try smith optics, I’m from Brazil an I do have costa’s couse I really love them but smith warranty it is so amazing. Take care 😉

Thanks I’m going to go try this now

Good job, been doing the same stuff for 55 years, started with mini bikes in the 70's. Never let anyone work on my machines. 👍

I Liked

Bought a used pontoon. Seats in perfect shape just stained. Marine 31 made them look like brand new. Only complaint I had was my dried out cracked working hands. burns. I suggest using gloves. Great product!!

Thank you for this, very helpful

Good advice sir

Great video going to try this 😊

making a game that is set on an oil rig, this will definatley help. :)

That’s true what one said about the gray line and I have own 8 two strokes and 3 4 strokes every year I get rid of the old gas and put in new a I use a good two stroke oil for what ever motor you have and I put seafoam in the gas tank and change fuel filter in them and they never let me down

Just bought a 2 stroke second hand 2005 15 hp 2 stroke Yamaha It starts OK but at idle runs a bit lumpy, can' t wait to try your tip as I was charged 500 dollars for my 4 hp Yamaha single cylinder impeller and tune up. in contrast I have my 2004 Mercedes Benz 6 cylinder tune up air con filer oil filer and oil change? it cost $470, Go figure - I'm with you brother learn by doing.and save big time.

The video talks about getting a replacement sensor on Amazon. I cannot find it. If someone has the link it would be appreciated.

Looking forward to the next review. Interesting that it heated the cold water when you first started it.

Having this exact problem. Took quite a while to find your video as it seems to be a much less common problem. Thank you very much for posting this!

"we may still be here" was the funniest comment i seen today. nice video

good wideo thanx.

After using bleach product, make shure you use diluted hydrogen peroxide. A ratio of 1 part 3% hydrogen peroxide to 10 parts water is effective for neutralizing bleach.

Bought a 2002 pontoon with a mercury tracker 40 hp two stroke outboard. Water separator had black mold in it when we test run it mold went into carburetor how do I get it out without over hauling the carb. I changed the separator,gas lines and filter. Now it won’t start.

I would like to tour BP contract with Diamond Offshore Drilling Rig in Gulf of Mexico

man those fuel issues are a bitch. 04 yamaha 50 2 stroke has a prime starter electric choke deal that is a dog. and oil injection seems to be way too complicated than just pre mixing. but looks like you got it figured out with that work you did. peace from grove, oklahoma.

My 2018 has door issues… going to try this. What’s the piece number?

Great to know I can try this

old gas will kill a motor clean the tank and get new filter every couple years

why talk so much extra? you could easily make this a 1- 2 minute video. why try so hard to waste peoples time?

Great presentation my brother! I just experienced this same thing today. Going back to the marina tomorrow and try what you just did. Thank you so much ❤❤🎉

What prop is that?

Good one yall, that's what we do here in GEORGIA if broke we fix but glad u got it running

So, after seeing this video and fixing my transducer following these instructions my pontoon now reads at full speed. I have a Lowrance Hook5. I will mention your transducer should be mounted on the driver's side of the pontoon. Problem cured. Thank you

I just bought a Helix 7 to attach to my pontoon boat. My pontoon sits in a boat lift and the cradle that the logs rests on sticks out about a foot behind the logs. A transducer can only mount flush with my logs, not hang down below or the transducer hits the bunk when I drive back on. I haven't installed it yet, Will it work flush along the bottom of my toon?

Just clean the carb like a grown up…

Launch looks familiar.

Like your video. I bought a new 90 hp 02 mercury 2 stroke still runs great. I had gray fuel lines on it and they came apart inside an found the way to the carbs. I took them apart and cleaned them. Runs great. I have a 16’ Lowe bass boat but I catfish only It will run about 40 mph. I have about 250 hours on the motor. I run a 12 3/4 - 21 aluminum prop. Take Care and God Bless from Hartford Ky

Sea foam is in every tank of my gas good insurance

Thanks, man! Funny, I have the exact same year and color, too! Yep, sliding door peeps randomly. Usually, when I'm going up hills.

Thanks brother I'm troubke shooting my 65 🐴 mercury even if it doesn't work appreciate u posting this I'm in the same boat when it c comes to doing it myself u have a new subscriber good luck and God bless (Rockwood Michigan)

Seafoam is an amazing product I use it to stabilize my fuel.

Never use carb or brake cleaner to start a 2t. You're washing the cylinder walls down and greatly decreasing the life of rings an bearings. Get yourself a good quality spray bottle and use premix to squirt into the carbs.

Very helpful, Thanks!

Where u were spraying the carb cleaner, what’s that location, looked to be where spark plugs are located, but normally on other side? Great video!

Good job

Wow, dry water pump= no more water pump paddles=replace water pump because you didn't hook up any water to it.

Just now saw your video....outstanding logic there Mate....just bought a Nissan 9.9hp 2 stroke that hasn't been run for over 6 years and I'm gonna add a can of seaform in the first tank of gas and see what the water looks like coming out after she starts up. I pulled the carb and cleaned it, new fuel pump, Impeller, and spark plugs....Hope mine goes as good as yours....and thank you for the time to make the video....

Thank you!

Beautiful.. As a lover of and once a chaser of 🌪️, this is beautiful. Yes, I understand the difference yet they're one in the same to me.

You are the man! Had to push mine in and out a couple of times. About to order 2 replacements. Thank you!

Gray line is for ethanol

Hey bud just a follow up from canada here. So I took out the 14ft fishing boat with a 25hp older 1986 mercury 2 stroke outboard . I fiddled with the screws and choke stuff ect before going on the trip and got to get it to start pretty good as I had previosly installed electric a starter ect ( cant pull on the cord to much anymore AGE you know what I mean )anyway up on the lake same kind of thing again, had to keep cranking with the starter to get it to fire up, when it did and got warmed up ,it ran like a bird, following day same thing lots of cranking then ran like a bird, its a 1986 but looks brand new Ive had it for 30yrs but hardly used it , now retired I use it more often, there cant be too much wrong with it as I mentioned it looks brand new, so I plan to try your method of cleaning with the gum out and sea foam hope it helps thanks for your time to share the info