I like my wen generator it works great and real good on gas

🤔🤔

Very bad impression of Darth Vader. I'll see if I can do better.

Nice. So a building "permit" was not needed because it is a farm, which makes it better.

I also ordered a 24x32 building, just like yours. I had the concrete put down 24'6" x 32'6". I sure hope the extra 3" around the edges is enough to prevent cracking from the anchors. If I have to, I will have them drill the holes, and leave it, so I can install my own epoxied anchors with all-thread. The broker (my neighbor) also did not write down exactly where I want the garage door, or the man door. He said they do that when they deliver it.

4-5 weeks I expect to see some tractor action taking care of that hay!! Updates all look great!

Can't wait till you hit 100k subscribers!!

Have a 1220 great tractor

My metal support beams went into the ground and cemented in. Who wants a bolt down shed a strong wind will take that thing up in the sky

Very good Sir. DIY concrete should be part of saving costs. You can put up a metal building which (shouldn't be insulated in your case?) built on a cast - dry stacked shell blocks and the cavities filled with concrete - concrete foundation wall (on concrete footings then) and only have a gravel floor and postpone the casting of the concrete floor inside the building. When you decided on the concrete work for the building. If you want to get up a little higher with the foundation. In order to protect the end of the metal sheet against the ground, when snow blows up against the wall. A good idea, and this also applies to wooden structures built at the time. By casting (or building with concrete and then reinforced vertical and horizontal shell blocks dry stack and fill the cavities with concrete) curb wall, you get a higher interior ceiling height at the same time if you mount the steel metal building on top of the curb wall. You get higher above the ground and protect the plate closest to the ground then. An alternative construction method (24x32 building in size) would have been and less expensive way and DIY then. - By building a Post beam construction with stabilizing batten sides. Then dress the construction (walls as roof) same material with own ordered steel metal roof plate (standing) panel 4 foot wide in size (easiest) you can come down in price vs. (ready bought from supplier) assembled total $11,000 (what you stated You paid for the building complete and set up then by a crew 24x32 in size). Thank You.

What was the frame spacing of the steel beams?

Why would you not give ALL the company names? Let others decide how they want to go about the process. Omitting the names will allow others to just remake the same mistakes you believe happened to you.

Nw fla

Our buildings are set on a lip below the floor 3/4 inch but still leak

What kind of seal at the top of center I get leaves blowing in under the cap

Cool 😎 !

Cool 😎. Crazy how prices are now . I put up a 24x50 with 10 ‘ walls and a vaulted ceiling ( Energy Truss ) . 2x6 walls ( stick building) . 4” cement and 6” pad where the lift sits,separate 200 amp service , insulated. Total 26K. This was the year 2000 .😮

Good looking building. I've watched a few other videos for metal buildings where people got shoddy work and are unhappy with their final building. I was nervous about my install until the day it was done. I had a 24x24 with 10' walls and vertical side panels put up about 18 months ago and mine came out great. I did do my homework and research tho.. and the company I finally chose to put my building up.. arranged for me to look at several other buildings they did in my area before I made my decision. I'm happy with mine. Anyway.. congrats on your new workshop.

What brand is the manufacturer? What part of the United States are you? I was looking into millennium building with 12g tube 26 x 35 with 16ft side walls

I just put up a 20x30 12 ft walls, my installers put a foam seal under the frame, and sealed the frame to concrete and sealed outside metal to the concrete, but i did put closure seals up the outside corners, each 3 ft long, 1.30 each, my pad is 30.5 by 20.5, so there is only about 2 inch exposed concrete

This makes me want to get one now!! I like the color too!

I just subbed.

Nice shop, I hope to build one next year.

Had to use a come along on my tension pulley to get belt on my RM 400 what a sob to do

Sorry folks, the comments were disabled for an unknown reason and are now enabled.

I want to start a small property business and I need a tractor I found a 1220 with a. Loader and a 3pt mower 4 wheel drive and I think it’s a hydro for $7500 is it worth it?

What did the mama cow say to the baby cow? It's pasture bedtime.

I can not stand Kubota hydro controls. Some people love them more power to them. When the local school district I worked for bought four BX series tractors, that is when the hate started. All operators were at least 55 years old. They were not beat on just mowing grass and sidewalk snow removal. Deck wheels broke off of two. One developed a rear axle leak. I hated the hydraulics, they do not work very good at idle. And the local dealer really put it to district on replacement parts costs. I know Kubota has a huge following, just my experience.

I am a retired service rep for Ford Tractor and if I can ever help you let me know!

Just a note of advice. These were very good little tractors. If you ever feel it is losing HP or the hydro is weak start with removing the muffler and operating it again. I have found these units with clogged mufflers and customers always think the engine or hydro is the problem.

I could have knocked this down for ya! Next time....Next time.....

We’re will the pollinators go?

I just bought one for 2300 hopefully it will serve me well for brush hogging

Folks, check the description for full details.

How does this mower climb?

Can you please make more video about this kubota. I really want to buy the b2320dt model.

I have a 1210 that I bought with a bad front ring and pinion gear. I have finally given up ever finding the parts and use it as a 2wd. Great tractor even as a 2wd, it has a loader and I only have 2000 in it. The parts for these are pretty unavailable.

Well as a deterrent a couple of well placed M18's may do the trick. I was really looking forward to the Spray truck application. Keep up the good work.

Can you make more video about the b2320dt? I really want to buy this model and have zero knowledge about it.

I need the prize

You guys are doing a fantastic job getting this site together! Looks great! Here's my joke: Chuck Norris doesn't need a crane to lift a building, a crane needs Chuck Norris to lift the building.

👏👏 👏 👏 let's go Brandon 👏 👏👏let's go Brandon 👏👏👏 let's go Brandon 👏👏

This Mr. Morgan Im the real Mr Kubota.

What does it look like inside??

Ten bucks a week, and all you can eat

Thanks for the update MRD!!

You know if you feed your cattle a little bit longer…you’ll get more than 4 steaks out of them!!

Very relaxing to watch …that’s some efficient machinery!

Burn, baby burn. Disco inferno!!!!

looks like you had a good yield from the first cutting