Stuff Box 23
0:35
7 ай бұрын
Stuff Box 18
1:02
7 ай бұрын
Stuff Box 9
1:46
7 ай бұрын
Stuff Box 7
1:27
7 ай бұрын
Stuff Box 4
1:36
7 ай бұрын
PixaTrack Installed White Soffit
0:07
Garry Morrisons Due PixNode Tree Fan
0:13
Пікірлер
@xBEASTxEDDIEx
@xBEASTxEDDIEx 3 ай бұрын
Where do I connect the raspberry pi
@glennfrancisco8559
@glennfrancisco8559 5 ай бұрын
No one wanted to comment so i did
@ranvirgorai7304
@ranvirgorai7304 7 ай бұрын
I have a standard pixel belt without any existing hole. I require a hole to be made every 4 inches along the entire length of the belt. The pixel belt i need is quite extensive, ranging from 1000 to 2000 feet in length (100 feet each roll).
@HolidayCoro
@HolidayCoro 6 ай бұрын
All our pixel strip is pre-punched on a machine with extreme accuracy. We do not sell "unpunched" strip and we do not punch third-party strip - sorry.
@zski1
@zski1 7 ай бұрын
Using the jig is great when the window or garage measurements are perfect. But my windows are slightly off. So, I have to make the edge hole 1/4 “ closer to the corner adapter for it to fit. I don’t see an easier way.
@zski1
@zski1 7 ай бұрын
Can i mount the pipe to the clip to like an inside of a garage wall. Meaning, would the pipe fit into the clip if the clip was mounted on the top wall of the garage opening, while the pixels are facing outward?
@HolidayCoro
@HolidayCoro 6 ай бұрын
Yes, you can absolutely mount the clips inside the door frame and then turn the pipe outward towards your audience.
@mcb0b1
@mcb0b1 7 ай бұрын
You don’t sell a “T” adapter?
@HolidayCoro
@HolidayCoro 6 ай бұрын
We don't sell a T but we do sell an X and you can leave on the extra section or cut it off.
@thereefaholic
@thereefaholic 8 ай бұрын
Would be nice to see human hands assembling the product rather than a computer pointer pointing at a drawing or a product page. After watching all of the mega tree videos I still am confused as to mounting an led ribbon to a black ribbon with holes in it.
@HolidayCoro
@HolidayCoro 6 ай бұрын
Always feel free to reach out to us directly for any assistance that the videos don't explain properly.
@jeffbekeris
@jeffbekeris 9 ай бұрын
Can LOR CF50 Floods be connected and controlled by the HinksPix V2 controller and xLights via the DMX connection? If so, what connector mod(s) would be necessary?
@HolidayCoro
@HolidayCoro 9 ай бұрын
Yes this can be done. Wiring is here: www.holidaycoro.com/kb_results.asp?ID=92
@jesseszypulski8545
@jesseszypulski8545 9 ай бұрын
Where’s the wiring path diagram for the candy cane 99?
@HolidayCoro
@HolidayCoro 9 ай бұрын
www.holidaycoro.com/models
@jakobpugh2570
@jakobpugh2570 9 ай бұрын
What about the controller connection?
@HolidayCoro
@HolidayCoro 9 ай бұрын
Reach out to our support at www.holidaycoro.com/contactus
@diyhometheaterguy
@diyhometheaterguy 9 ай бұрын
Nice video! I am new to this style of lights and this was helpful. Just installed the lights on the house and apparently have a damaged node from the installation. Tested OK before but now bad. I'm hoping it's just the one like in your video!! What causes these to randomly go bad?
@HolidayCoro
@HolidayCoro 9 ай бұрын
A variety of reasons occur - physical and electrical. Just like all electronic products, they can go bad.
@phatadam123
@phatadam123 10 ай бұрын
These new pixel pipes - are my fav new product!!
@LightsOfElberfeld
@LightsOfElberfeld 10 ай бұрын
isn't it true you can just tilt the stake back slightly? Arent rgb pixels non-directional?
@HolidayCoro
@HolidayCoro 9 ай бұрын
No, pixels are brighter when viewed strait on compared to being viewed on the side of the node.
@goldenpacificmedia
@goldenpacificmedia 10 ай бұрын
Just checking into this comment section - this walk through is great!
@ColbyHiggs
@ColbyHiggs 10 ай бұрын
Great video. I appreciate all the details!!
@no1unorightnow
@no1unorightnow 10 ай бұрын
You said everything but the title - HOW it works? For example, an explanation of the schematic?
@HolidayCoro
@HolidayCoro 9 ай бұрын
Sorry about that. It works by repeating the signal further.
@nethoncho
@nethoncho 10 ай бұрын
Nice stage
@edlerlights6486
@edlerlights6486 10 ай бұрын
Can you drive 2 easypixs daisy chained?
@HolidayCoro
@HolidayCoro 9 ай бұрын
Yes you can!
@jeremyjones9667
@jeremyjones9667 11 ай бұрын
I'm a little upset that you don't support this product that i purchased from you guys! I now have to spend $500 to get another controller.
@HolidayCoro
@HolidayCoro 9 ай бұрын
Please contact the mfg for support, we are legally no longer allowed to support this product as the request of the mfg.
@nethoncho
@nethoncho Жыл бұрын
Lookin nice
@HolidayCoro
@HolidayCoro 9 ай бұрын
Appreciate it
@billnordgren
@billnordgren Жыл бұрын
The delay is about 5 to 8 seconds for the lights to turn on. How do you get them to be instant like a normal pixel? I can't use them if they don't turn off and on with the rest of my lights.
@HolidayCoro
@HolidayCoro Жыл бұрын
This is not a pixel flood issue, it is a software issue. Please reach out to our support staff for more information. One common way to determine if this is a software or hardware issue is to use the built-in test mode on the controller.
@billnordgren
@billnordgren Жыл бұрын
@@HolidayCoro In further testing I found that when I defined a string that only had 2 pixels (6 channels) that the HinksPix controller did not send enough power to light the 10-watt flood light in a timely manner. They need more power than a single pixel. Putting 100 nodes on the string model (300 channels) in Xlights and only using 2 nodes for the floodlights seems to have solved the problem. Testing through the web interface of the controller it works fine. it only seems to have the problem when sequencing through Xlights when the model was assigned its own universe of 2 pixels (6 channels) and sent out a single port on the controller..
@peterzinia3767
@peterzinia3767 Жыл бұрын
When you split the 100 string into two 50 strings you might want to incorporate a fuse at the start of the 2nd set. The 1st of course has the fuse already. If your going to make videos you should do it properly so anybody that views them & follows your instructions doesn't end up burning their fucking house down. Just a thought.
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, safety first!
@peterzinia3767
@peterzinia3767 Жыл бұрын
Those "little plugs" are commonly referred to as Vampire Clips or Vampire Ends.
@Penfold8
@Penfold8 Жыл бұрын
The only thing I noticed about this setup is that it looks like it would be a nightmare trying to replace a burnt out pixel and salvage the candy cane.
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, you are correct - this is a design from 2014 and I'd recommend item number 261 which uses nodes.
@nibs991
@nibs991 Жыл бұрын
Hi there I emailed less than a week ago and spoke to a person about an issue with this controllers decoder mode not working with the Newer frosted Globes you sell. I have everything setup exactly as this video shows but when you get to timestamp 4:07 you change Ic type to 2811 and all pixels react as they should (lighting up showing they’re recognized similarly it’s stated this should happen in decoder mode in “Why do HolidayCoro pixels turn blue sometimes” in your website’s help section) I do have everything activated as following: #pixels: 170 Ic Type: 2811 LED RGB SEQ: RGB All control: No Rev Control: No When adjusting LED RGB SEQ setting it does change the colors of the first 3 pixels in decoder mode. However the software I use to program the lights is vixen. It still states on the page for this product that this controller works with that program however I have had 0 luck with getting these bulbs to react to any input. Master mode does work perfectly as well. I’m responding here as communication seems to have ceased and the info from your help section did not offer a solution for “if none of the lights are blue and your controller’s #pixels setting is set to the maximum” I will state that this issue does not exist in your Ribbon lights as the ones I threw away to replace with these bulbs worked properly they were just very beat up and starting not to fully work.
@HolidayCoro
@HolidayCoro Жыл бұрын
We are sorry about this situation. It looks like it was addressed by customer service.
@pedrogrimaldo-bs9kq
@pedrogrimaldo-bs9kq Жыл бұрын
where can i find the firmware to download
@HolidayCoro
@HolidayCoro Жыл бұрын
www.holidaycoro.com/firmware
@zski1
@zski1 Жыл бұрын
If I'm Power injecting from a 2nd supply for the same string with multiple PI points, do i need to cut the V+ from all the tees? Or is the first cut on the first PI point good enough.
@HolidayCoro
@HolidayCoro Жыл бұрын
That is covered here www.holidaycoro.com/kb_results.asp?ID=173
@zski1
@zski1 Жыл бұрын
Question, stead of removing the positive pin from the PI cable when using a 2nd PSU, can I only connect the ground wire at the disto. board?
@HolidayCoro
@HolidayCoro Жыл бұрын
Power injection is 100% custom for each customer's setup and thus it will require each customer to complete a unique design.
@mikeyandalyssab4782
@mikeyandalyssab4782 Жыл бұрын
When doing roofline, how would you recommend handling the corners? Do you have corner adapters or 90 degree pieces?
@HolidayCoro
@HolidayCoro Жыл бұрын
The strip is cut, then a small section of #696-100 is soldered to turn around the corner.
@zski1
@zski1 Жыл бұрын
Won’t I need to power inject if I use all these ports?
@HolidayCoro
@HolidayCoro Жыл бұрын
No, each port can have up to 60 watts of power.
@sanjpl48
@sanjpl48 Жыл бұрын
Hello, holiday coro, your singing christmas tree is what i have been looking for in xlights. How do i get it, without buying the actual product to connect. And i am talking about one i saw in a demo 9 years ago.
@HolidayCoro
@HolidayCoro Жыл бұрын
Contact us at [email protected]
@phatadam123
@phatadam123 10 ай бұрын
did you get your model? I have the Holiday Coro singing tree - its available in the xlights google drive.
@BillStephens-xq4kc
@BillStephens-xq4kc Жыл бұрын
I spent hours flashing my lights without success before watching your instructions. Perfect.
@BrandonJacobson
@BrandonJacobson Жыл бұрын
If anyone is trying to setup a hinkspix pro controller with flood lights, please consider watching my step-by-step video here: kzbin.info/www/bejne/o6akqqqCortlfdk
@Kevmoens
@Kevmoens Жыл бұрын
I suggest on the pages you select to buy these items have a link to these videos. It took me a bit but in my head I was worried that the Regular controller didn't work with smart pixels. This video answered my question.
@BrandonJacobson
@BrandonJacobson Жыл бұрын
I just bought my controller and flood light and received them today. I'm so excited to get this light show going!
@HolidayCoro
@HolidayCoro Жыл бұрын
Have fun!
@BrandonJacobson
@BrandonJacobson Жыл бұрын
@@HolidayCoro thanks!
@kylekrantz2945
@kylekrantz2945 Жыл бұрын
i can not open an existing design
@HolidayCoro
@HolidayCoro Жыл бұрын
Make sure your SD card is compliant: www.holidaycoro.com/kb_results.asp?ID=206
@nataliesteadman478
@nataliesteadman478 Жыл бұрын
Having trouble with configuration. Keep getting the following error message The Controller's Port is limited to 4 Universes or 2048 Channels. Port 1 Has 3618 Allocated I have the Hinkspix pro with 1 Longrange and 2 SPI Boards. I have 2 Smart 16's daisy chained to jack 1, and 1 smart 16 connected to jack 2 on the longrange board. Each of my physical ports (xconnect) have less than 150 pixels per string and I am not even using all 16 xconnect ports.
@HolidayCoro
@HolidayCoro Жыл бұрын
The number of pixels per jack/cat5 cable is 680 * 4 or 2,720 pixels. Move one of your 16 long range receivers to another jack to free up pixel counts. Don't configure more pixels per output than you are physically using, for example, if you are using 150 pixels only use 450 channels, not 510 channels. If you experience additional questions, contact us at www.holidaycoro.com/contactus
@gregoryrivara9003
@gregoryrivara9003 Жыл бұрын
Are the network IP address and the controller IP address different?
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, the PC and controller must have unique IP addresses.
@amarioreyes
@amarioreyes Жыл бұрын
What's the video in which you show how to sequence the singing tree ?, I was looking for it in the library of videos but unable to find it, can you please add a link to it in the reply ?.
@HolidayCoro
@HolidayCoro Жыл бұрын
Sequencing is a software function, not with the prop itself. I'd recommend searching for your application such as: xlights singing face sequencing tutorial
@gregoryrivara9003
@gregoryrivara9003 Жыл бұрын
Do we need to have the controller connected to our network to test our pixels to make sure the pixels work with controller? At 3.20 you mention that we need a network connection to be in test mode? Are you referring to testing the output with xlights?
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, you can test using the built-in test mode on the controller without a network.
@jeffbekeris
@jeffbekeris Жыл бұрын
Is there a model template available to import into xLights for the Singing Christmas Trees (8 channels total of 818 LED Mini-Lights)???
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, email [email protected] for a model.
@luv14lyf
@luv14lyf Жыл бұрын
Do you have anything to increase the power & data? Or something to just increase the power? You mentioned that even just running a wire 50' from the controller won't help boost the data so are you saying a data booster is the only way to boost it? I need to run about 250 12v 30mm pixel point leds and need a simple way to inject power and boost data. I'll be using 16/3 to first string and any jumps, 16/3 or 16/2 for power injection and 18ga for data from a 350w power supply.
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, you could use a higher voltage to start with on your pixels. Or you could just drop the % output to reduce power consumption of the lights. Physics is physics.
@luv14lyf
@luv14lyf Жыл бұрын
@@HolidayCoro do you mean use 24v or 48v pixel point
@jimtownsend7899
@jimtownsend7899 Жыл бұрын
I am replacing an 18' lighted garland with another one. The lead cord on the new one is much shorter than the lead on the old one. Can I just cut the leads off both light sets and solder on the longer lead (from the old set) to the new set?
@tzabel2
@tzabel2 Жыл бұрын
I have just received an 8 SPI smart expansion unit that will be receiving data from my main HinksPix Pro. I was under the impression that I will run ONE Cat 5 cable from my HinksPix pro to the 8 SPI expansion unit--is that correct? I see that I received a 1 foot Cat 5 cable with my order--is that to connect to 2 4-output boards in the expansion unit so that they are in effect daisy chained within that box?
@HolidayCoro
@HolidayCoro Жыл бұрын
Yes, the 1ft cable is to link the two boards together internally so you only need one CAT5 cable to the unit.
@hobbs3424
@hobbs3424 Жыл бұрын
I have 2 sortimo boxes with metal lids and foam under the lids, stops washers and small screws leaving compartments, they are absolutely worth every cent
@steveschappell8374
@steveschappell8374 Жыл бұрын
While this is not exactly the same, I am asking for help. How does an animated snowman work? For example one where the arm waves, or is tossing a package. I understand the wire frame and lights, but how does it flash in sequence, while the other lights stay static? I am searching to understand how it works and cannot find anything.