jak te gumy się trzymają, że nie zostają wciśnięte do korpusu razem z kwadratem wahacza?
@automarcprzyczepy4 ай бұрын
Prima
@user-ps4db7rx2s6 ай бұрын
vă rog mă puteti ajuta cu un ne de telefon să fac o programare
@wwaaYYnn33 Жыл бұрын
Habe solch eine Achspresse zu verkaufen - i have such a axle press for sale - PN
@kondratib Жыл бұрын
foglalkoztok javitasal is, nekem az egyik felen elszakadt a gumi es nagyon meggyengult tole a rugozas
@dzsingiszkan1001 Жыл бұрын
Mi akadàlyozza meg a kicsúszását?
@ferencmiko5778 Жыл бұрын
Ha cserélni kell akkor hogy lehet ki szedni a régit?
@kondratib Жыл бұрын
hali, sikerult kicsereljel ilyen gumikar?
@alexandrumezei12052 жыл бұрын
Kerladjek egj telef szamo
@motustrailer47463 жыл бұрын
Very Good!! A question: how long are the rubber bars and what material are they made of? Polyurethane? Rubber? Elastomer? And what is the diameter of each of them? With how many kilos of pressure does the hydraulic press work? Thank you very much for your kind attention. Greetings
@wwaaYYnn33 Жыл бұрын
Have a press for sale
@provaznikendre12143 жыл бұрын
megérdemelt volna ez a klipp egy gyártástechnológiailag és videozásban is jártas szakember irányitását a könnyebb felismerhetőséghez.-Pontositva a cimet: itt a gumitorzios tengelyről van szó.
@Luuxs3 жыл бұрын
if i want to import them how much wil they cost each.
@tonychearnley32363 жыл бұрын
I have made my own independent suspension units with 50mm box, 30mm square section and 18mm 70 shore rubber all pressed in in a home made press, works well, I used silicon spray as a lubricant.
@alb.patrickke52433 жыл бұрын
Hi Tony, thank you for sharing as I have been planning to do the same. You mean 18mm diameter for the four rubbers - one per corner of the 30mm square, right? How do you keep them steady or not being pushed while the square thingy is being pressed in?
@tonychearnley32363 жыл бұрын
@@alb.patrickke5243 Send me a mail at [email protected] and I will show you all.
@enterBJ403 жыл бұрын
Could you provide me with some advice if I write you? I have a russian made boat trailer which has the rubber protruding from axle. Are dry rotted and need replacement. Perhaps you can show me the way :).
@sergiosanmartin4 жыл бұрын
Quien coño es el que elije la música???????????
@freedomfreedom8744 жыл бұрын
Hallo, wo befindet sich dieser Workshop? Ich muss meinen Anhänger reparieren
@victor0105924 жыл бұрын
👍🏽
@thomasweiser87905 жыл бұрын
Macht ihr auch Instandsetzungen also Tausch der Gummischnüre? Wenn ja wo?
@SenthilKumar-yb2ck5 жыл бұрын
Hi we trying to do this rubber insert on different application. would you be able to give some idea where can i get the plastic to keep the rubber in place and also the plastic end cap for insert axle (black part shown on the video)
@sincro-o-matico7415 жыл бұрын
Oq impede de não sai de dentro
@brasilcustomtrailer39656 жыл бұрын
Perfeito
@evilsideracing6 жыл бұрын
And then after a few years the rubber dry rots and the swingarm rips off. Happened to me a few days ago. Totalled my trailer. Not a very good design if you ask me.
@luigicirelli25834 жыл бұрын
mine's slightly protruding on one side; probably impossible to push back
@suntittle6 жыл бұрын
how much PSI is needed to press the axle in the tube?
@valtersmezulis84066 жыл бұрын
How N press?
@suntittle6 жыл бұрын
Just what i was looking for! Thanks for posting!!
@suntittle6 жыл бұрын
How much psi is needed to push the pin between the rubbers
@INSPECTOR738 жыл бұрын
ПИПЕЦ! ЭТО ЧЁ КАМЕННЫЙ ВЕК? РАЗМЕРЫ РУЛЕТКАМИ АЛЕНИ МЕРЯЮТ,ЛИКАЛО НЕТ ГОТОВОГО ЧТО ЛИ ,ЭТО ЖЕ ЗАВОД. УЖАС!!!
@yarizaytbeatriz69037 жыл бұрын
INSPECTOR ko0
@yarizaytbeatriz69037 жыл бұрын
i89
@andrewwilson83178 жыл бұрын
So the only thing holding the sprung part in the axle tube is friction on the rubber sections?
@yarizaytbeatriz69037 жыл бұрын
Andrew Wilson p
@Destroerr10 жыл бұрын
Класс. А смазывают квадрат мыльной водой, что бы хорошо заходило в резинки.