Hey man your inner tie rod needs to be replaced it's not supposed to move that freely and you must pull that boot over the lip at the end.

Silly comment but GB sealant is so expensive I think I might use liquid nails to glue the back wall piece of the niche and save the GB for the screws and other seams.

The 3/8" socket indentation wehre the oil is draining over around 12:45 is the drain plug for the transmission. Recommend dropping the fluid and replacing it especially if your car has a lot of miles on it. Put it in a clean pan and inspect for signs of metal shavings. Refill with OEM Honda transmission fluid.

Where did you find the aftermarket radio from

Are there mechanics that will do this for me? I tried twice already and it is scary to do. EGR still not ready.

And I thought my bathtub / shower was ghetto

2025 gang gang

this is a comon sense super video; difficult to finf something better than this; thank you!

Would love to see 2006 in the video title. Just saying "Subaru" isn't helpful

Sounds awfull

I hope it works. I think this is not safe to do in the city. Oh well.

Ohh my gosh, stop moving the camera so much.

Probably a faulty door sensor or something lol

Thanks.

it worked thanks

Who drives 20 on freeway???

And then there is the medical S Y S T E M afterwards............

I used my spare key and it worked.

Hi, great video very informative, just curious about the transmission if I needed to put it on neutral while doing valve adjustment or stay on park because I got A/T trans. Thanks

🎉thanks for this video it helps. I been searching for reasons for so many days

Iam.Bangladeshi,,❤

Simple video. Straight to the point! Thanks mate

Helpful

Nice to hear there are other ways. Great tutorial.

How did it hold up ? did it ever leak?

Anyone watching this in the future... please REMOVE THE AIR VENTS as well and you won't have to force the cluster past them, and putting it back together is ten times easier!

Best tutorial ever!

bro omfg THANK YOU! even chatgpt couldn't be clearer holyshit

thank you.. very helpful! replaced the driver side today.

I know it’s kind of late.i was wondering if there was 2 power leads to pump cause i got thin yellow and black and a thick yellow and black with power only going to the thin yellow.before i buy a pump does the pump and sender share the power lead or is there 1 for each?cannot find any info must be straight forward but its an expensive mistake

I have an existing daisy chained pot lights in my kitchen..Is it possible to add a totally different light fixture (same wattage)on the same chain ? Thx.

That little bracket on the rear of the compressor is the only part I've got left over after my rebuild😖😆

L 😊

شرح جميل وسهل الصراحة

Ive got one of those under the drivers seat thats not making good connection.Sometimes i crank the car and the lights off then after driving a ways it comes on. I think there are 2. Im going to try zip tying tgem snuggly to see if that stops it.

You shouldn't use any metal object across the phone charging terminals, it's about as useful as cleaning a toaster with a wire brush when it's plugged in! (Please don't!).

Awesome video! Thank you!

Salute to you my man!! This auctually worked!!!! Thanks big time!!!!!!

Simple and direct, great video

AWESOME MAN

Another CRITICAL part of the drive cycle is you can't have a full gas tank --it must be at 1/2 full or less (FACT).

What shower pan did you use? Also, does the go board sit flush with the shower pan flange? Thanks

That you mean support it

Which kind of spray you use

Holy cow man thank you.

Dantdm?

`thanks for taking the time to share. Living in goat head country I found that tire sealants are not enough.

Thanks! Great video

Thanks a lot

This doesnt work in all cases at least in my experience. I tried to do that with pandas and got the wrong .whl file, it was windows instead of linux, therefore my lambdas never executed. I had to spin up a docker container and pull amazonlinux:2, install pandas and then load it as a layer to get it to work