What did u have to do for the speed sensor from the automatic to manual, best videos about this swap i have found
@omoffroad6 ай бұрын
Matt86toy, the speed sensor is located in the transfer case, so it remains the same with either transmission.
@matt86toy6 ай бұрын
Ok thanks for the reply mine is 2wd tho
@omoffroad5 ай бұрын
@@matt86toy , I have not swapped a 2wd but I would assume the speed sensor in the 2wd tail housing would be the same in both transmissions.
@jameyboss37 Жыл бұрын
I just noticed your truck came with a “ball cooler” pretty neat, my 94 didnt offer that, sweet build very clean I hope your truck takes you a great distance👍🏽
@luispina4012 Жыл бұрын
Same transfer case from the automatic transmission?
@omoffroad Жыл бұрын
Luis Pina, yes sir same transfer case.
@luispina4012 Жыл бұрын
@@omoffroad 👍
@dustinriggs5396 Жыл бұрын
Did you have to pull dash to put in clutch pedal and brake pedal?
@omoffroad Жыл бұрын
No. The pedal assembly can be installed from underneath. All of the holes are either already there or marked from the factory.
@dustinriggs5396 Жыл бұрын
@@omoffroad awesome. I was In the process pulling out everything from the donor truck and I have the whole dash and harness out but really didn’t want to have to pull my main trucks dash. Your video has helped and answered a lot of my questions. Did you have to remove steering column to get to install the pedals?
@omoffroad Жыл бұрын
@@dustinriggs5396, I don’t think I did but I honestly can’t remember. I know I lowered it to delete the cable that keeps you from turning the ignition unless the brake pedal is depressed in park. Watch all of my videos on the swap. I know I mentioned it in one of them.
@christhomas8912 Жыл бұрын
Hey where you located I need one
@omoffroad Жыл бұрын
I don’t sell them buddy I just built that one for a friend. I’m in Gulfport, MS.
@johnmead843711 күн бұрын
@@omoffroad Do you get multiple catches? Having a rubber surface on the closing faces of the doors would reduce noise if that were a factor. Camera evidence of pigs reacting would help understand if this is effective or a niche situation device. How does it stand up to a serious boar intent on damage?
@josiahheinrich87962 жыл бұрын
What did you do with the wiring that goes to to the automatic transmission?
@omoffroad2 жыл бұрын
Josiah Heinrich, I believe I discuss it in one of the videos about the truck, but if memory serves, I had to connect only two of the wires to the manual transmission. The only two wires used were for the reverse light switch. I simply pulled a tail light to see what color went to the reverse lights.
@TheLuisl72 жыл бұрын
Hey i have a few questions about it i will appreciate your time
@omoffroad2 жыл бұрын
Luis Camargo, what’s your question sir?
@jakeknelsen40032 жыл бұрын
Hi I’m doing a Manuel swap in my 96c1500. The Manuel is out of an 88 did you need a flywheel spacer? Looks like I’ll need one
@alexanderpuckett4432 жыл бұрын
I got a 1979 C10 with 350 small block 4 speed and I was wondering what do I need to make my nv3500 to work for my truck?
@josepavez1232 жыл бұрын
Necesito el piston con anillos de la 757 shindaiwa
@omoffroad2 жыл бұрын
🤷♂️
@CelindaSnyder2 жыл бұрын
Do you think this design will work for coyotes too?
@omoffroad2 жыл бұрын
You would really have to cover the floor well with dirt then see if they would trip the wire. It would definitely hold them if smaller wire was used.
@Bree08142 жыл бұрын
I know this was a long time ago but I’m hoping you might can help One-can you take the transfer case off the automatic 97 transmission and use it (I believe it’s a 4l60-e ) on the Chevy 5 speed But my main issue is my truck is a 96 extended cab 1500 4x4 but came with a 4.3 with a 5 speed before I got the truck the 4.3 5 speed was pulled and my father in law took a 97 350 vortec with the 4l60-E and put it in and now the trucks just awful it takes off in I’m guessing 3rd shifts to Drive and never does go in OD I tried putting a 97 dash and harness in it but I couldn’t get the main plugs to work. So my plan is just put back a 5 speed. Because of the shifting my odometer don’t work trip or reverse lights but idk which one I use I have a nv4500 but it was 2WD so idk if I needa find another one or what. It seems you know what your doing. I’m just stumped. Please help! Lol if you can
@omoffroad2 жыл бұрын
Shane, the 4L60E will not shift because the factory ECU came from a manual transmission truck so it will not control the shifting on the automatic. Where is the transfer case that came behind the original 4.3 5 speed transmission?
@tranquility76922 жыл бұрын
Came here after my 97 blew the 4l60e for the 4th time in 3 years. Looks like a bugger to do but might just have to at this point.
@omoffroad2 жыл бұрын
Depends on how mechanically inclined you are but definitely worth it.
@tinhtran13092 жыл бұрын
how tall piston?
@omoffroad2 жыл бұрын
How tall? It was a stock replacement.
@Cody-cy5fn2 жыл бұрын
I keep getting rev hang and high idle with the factory computer
@omoffroad2 жыл бұрын
Is your speedometer connected and working? The VSS (vehicle speed sensor) might be affecting the idle?
@Cody-cy5fn2 жыл бұрын
@@omoffroad everything hooked up fine correct everything works as it should mainly hangs in between shifts, sometimes till I come to complete stop
@Cody-cy5fn2 жыл бұрын
Also when it’s warmed up
@80sDweeb2 жыл бұрын
Very helpful to know the details like the computer, and the key lock cable in the column.
@jasonmartin93932 жыл бұрын
Hay is there any way to get ur phone number I have some questions about what u did if u don’t care
@omoffroad2 жыл бұрын
Man, I’d rather not post it up…. I’d like to help you anyway I can though so if you have qualified ask away.
@omoffroad2 жыл бұрын
*question
@jasonmartin93932 жыл бұрын
Thanks buddy I Ben needing help and don’t have much money I have a 98 Chevy Silverado 2wd with a 4l60e I got a 5 speed transmission and wanting to put in mine As long as I keep the automatic transmission in park Will it be alright Do I have to keep the shift select box plugged in Under the truck how do I do the speedometer
@omoffroad2 жыл бұрын
@@jasonmartin9393, my truck was a 95 4wd with a 700r trans. I unplugged the automatic transmission electrical connections completely and removed the shifter from the column. The only wires you should need will be for the backup lights. I don’t know what the 4L60 speedometer connection looks like vs the NV3500’s so I can’t comment there. I will say if money is tight and you’re capable of doing this work you’d be money ahead having your automatic rebuilt instead of swapping it.
@jasonmartin93932 жыл бұрын
@@omoffroad hi thanks for the reply I think I’m making progress on it I finally got the clutch pedal in man it was hard I got the transmission in but had to drill new holes for the cross over for the transmission And I have the master cylinder in but had another problem I had to get a different yoke from the jun but I got it for free and had to find a bastered u joint for it to go to my drive shaft and that was a hard find don’t no if I’ll need any thing yet ant got no farther yet on it. But I did get it to start off the key there was a park neutral safety switch under the truck I had to fix so it would start can’t wait to try it out
@kenneth97613 жыл бұрын
You are the hero we need
@omoffroad3 жыл бұрын
Thank you sir, glad I could help.
@user-be9ii9ut4t3 жыл бұрын
Um..ummm ..ummm.um
@omoffroad3 жыл бұрын
I see you have no videos posted for me to troll.
@user-be9ii9ut4t3 жыл бұрын
Ummm...ummm...ummmmm
@omoffroad3 жыл бұрын
🖕🏻
@user-be9ii9ut4t3 жыл бұрын
Disrespectful ass
@omoffroad3 жыл бұрын
@@user-be9ii9ut4t, yes sir you are. I try to post things to help people making this swap. You troll me making negative comments. I countered with a negative comment. Are you surprised?
@nicolasvaccaro69953 жыл бұрын
00 you sound like someone with a real paper asshole
@Riggsj773 жыл бұрын
What kind of transfer case I am five speed swapping my 03 chevy1500 and the transfer case won’t line up with the splines
@omoffroad3 жыл бұрын
What transfer case do you have? You can replace the input splines if necessary.
@aaronking45283 жыл бұрын
What did you do wire the reverse lights?
@omoffroad3 жыл бұрын
Aaron, read the comments below addressing the reverse lights sir.
@jeremys14963 жыл бұрын
Beautiful truck wonder how much more difficult the nv4500 is
@jeremys14963 жыл бұрын
For a 3/4 ton of course
@omoffroad3 жыл бұрын
@@jeremys1496, can’t be anymore difficult and a far better transmission too.
@gilbertgutierrez57512 жыл бұрын
@@omoffroad I have the same problem, I have a 94 chevy 2500 4x4 that needs a new tranny buts it’s a auto and would like it to be a 5 speed anyway I could get in contact with u beside on here?
@jamesshonk5653 жыл бұрын
Good idea. Nice build.
@traveller47383 жыл бұрын
I live in New Zealand and I’ve been looking a design like this, you nailed it mate. Do you have plans that you can sell or pass on? I’m looking to make one that I can dismantle for easier transportation in the forest by one person.
@Nopeandnope38613 жыл бұрын
Bought a round one with open top...same saloon doors. Works great. Redriverarenasdotcom
@ayp19383 жыл бұрын
nice hoping to do a 5 speed swap on my 89 k1500
@robbiemcgee24823 жыл бұрын
Hey man I looking to do the same thing in my truck if you could get back with me it would be very much appreciated i have a few questions
@omoffroad3 жыл бұрын
What is your question sir?
@ExploringCabinsandMines3 жыл бұрын
Uuhhgg more trouble than I thought. how did it turn out ?
@omoffroad3 жыл бұрын
I posted a follow up video, check it out.
@ExploringCabinsandMines3 жыл бұрын
@@omoffroad I found it good job ! now come do mine ! 😆
@joshjones77573 жыл бұрын
Need some black wheels buddy look 110 better!!
@omoffroad3 жыл бұрын
Josh Jones, naaaaa man I’m rolling that factory steel.
@joshjones77573 жыл бұрын
@@omoffroad I get it but have u considered getting them widened there used to b a guy n salesman GA that done a set of jeep Sally's for me years ago n I think it was only like 40$ a wheel to get that 10 inch poke n that would still n running the factory steel but with a lol more style lol but I even then still think they should b painted black but I do u brother different strokes for different folks lol 💯😉 have a good one brother
@diamondpointgunsmithingllc26123 жыл бұрын
Did you have to do anything to computer? I'm looking to put on a 97 5.7 trying to figure out what I have to do. Thank you
@omoffroad3 жыл бұрын
I did not do anything to the computer. I ran the same one from the original automatic set up.
@danielgarza85994 жыл бұрын
Basically the same for 2 wheel drive ?
@morganflakes31644 жыл бұрын
I finished my 96 about 1000 miles ago does yours rev up to like 1500+ rpms when you slow to a stop then idle down when it comes to a complete stop?
@omoffroad4 жыл бұрын
No sir my engine goes straight to idle as soon as I push the clutch in.
@tater09094 жыл бұрын
I wanna do this to my 97. I have the 5.7 v8. 4x4
@ToxicJuice-yt5zf4 жыл бұрын
I know this video is old but did you get a check engine light with running the automatic transmission computer?
@omoffroad4 жыл бұрын
I didn’t have any check engine lights come on after the swap.
@hugoetorres37374 жыл бұрын
Hello I have a question about the transmission standard where is a good place to ordered it ? Can you shoot me a text 4694554821
@omoffroad4 жыл бұрын
I purchased mine from a local individual from a 2006 Chevrolet truck.
@mcrangelvlogs93964 жыл бұрын
What standard transmission would you put for a 5.3l? Thank you.
@Avalanchef1fitty4 жыл бұрын
I’m using a nv3500 in mine.
@clappedclassics98464 жыл бұрын
This is actually a really neat design. Lemme know If it works!
@danithaman46104 жыл бұрын
Why didn’t you go with the nv4500?
@gabelossus Жыл бұрын
There's no need to with a stock 350 or especially the 4.3L V6 he's got. The NV3500 is rated for plenty more torque than that will ever put out even during burnouts. If you go with a modified 350 or up to a 454 though thats a different story
@lopezhanna17034 жыл бұрын
How did you get the automatic wiring harness to plug into the nv3500? Or you didnt connect them at all?
@notmedrano34324 жыл бұрын
Anyone know what kind of Manuel transmission a 1989 GMC 350tbi 1/2
@morganflakes31644 жыл бұрын
Does the cruise control still work?
@omoffroad4 жыл бұрын
Morgan Flakes, the cruise would not be affected after this swap.
@willmorris22734 жыл бұрын
Can I use the same slave cylinder for the NV4500?
@omoffroad4 жыл бұрын
Will Morris, order the correct slave cylinder for the NV4500 for the same year 3/4 tin truck and it should work fine.
@willmorris22734 жыл бұрын
omoffroad I hope it will it shouldn’t change due to an engine swap should it? It had a 305 and a automatic and now it has a P-Pumped 24 valve cummins and I want to put a 5 speed in it
@omoffroad4 жыл бұрын
Will Morris, I have no way of knowing if it’s the Dodge NV4500 or the Chevy one 🤷♂️
@gordonconroy8424 жыл бұрын
What type of clutch bracket did you use plus did you connect clutch safrty switch and cruise cut out
@omoffroad4 жыл бұрын
gordon conroy, this truck didn’t have cruise control so I eliminated the switch. Watch my previous videos that discuss the bracket.
@gordonconroy8424 жыл бұрын
@@omoffroad did you use the clutch saftey switch the piece that's on the master cylinder
@omoffroad4 жыл бұрын
gordon conroy, I honestly don’t recall a clutch safety switch at all. If I don’t mention it in my other videos I would have bypassed it by soldering the wires together. It’s just a two wire circuit on a normally open switch.
@elmerarrieta85024 жыл бұрын
hi I have a question recently I asked my standard truck but it does not start the gear if it works but there is no current in the truck and I wanted to know if I have to add some cables or something
@omoffroad4 жыл бұрын
Elmer Arrieta, I apologize sir but I do not understand what you are asking me?
@elmerarrieta85024 жыл бұрын
hello I have a 2004 chevrolet was automatic and I want to make it standard and I already put the standard transmission and everything else but I left the connector of the automatic to turn on but try to light but does not turn on it does not turn anything on the truck or lights go nothing just the march I could do
@MrDJNeddo4 жыл бұрын
Heyy, im also wondering what you did for the wiring for the reverse lights, doing the same swap now, nv3500 from a 97 4.3 is going into my 91
@omoffroad4 жыл бұрын
dawson neddo, watch all the videos I’m fairly sure I covered it but what I did was pulled a rear tail light to confirm the color of the wire going to my reverse light bulbs. Mine were light green. I then located the ends of them on the switch on the side of my auto and simply moved them to the reverse switch on the manual trans. Simple as that sir.
@MrDJNeddo4 жыл бұрын
Thanks alot:)
@omoffroad4 жыл бұрын
dawson neddo, happy to help sir
@denverbevins40524 жыл бұрын
never heard one fire-up so nicely - great job
@omoffroad4 жыл бұрын
denver bevins, thank you sir! Still have it and really need to rebuild the engine due to leaks and oil smoke. I use it once a month to grade my road.
@denverbevins40524 жыл бұрын
@@omoffroad I have a 47 which needs some attention. Probably just a condensor but it has not moved in a year.
@omoffroad4 жыл бұрын
denver bevins, I converted this one to electronic ignition. No more points is wonderful just don’t ever accidentally leave the ignition on overnight or it fries the module
@nextlevel66634 жыл бұрын
Is there a video of the finish?
@omoffroad4 жыл бұрын
Next Level, yes sir there is just search my videos. I did a follow up almost a year later I believe
@matthewrobinson5474 жыл бұрын
This helps out a lot should the drive shafts and cross member be the same on. 95 Sierra with a 350
@omoffroad4 жыл бұрын
matthew robinson, thank you. Yes, the driveshafts and crossmember should be the same.
@matthewrobinson5474 жыл бұрын
Thank you so much
@tysonballer22404 жыл бұрын
Why did u swap the brake pedal? What's diffrent.
@omoffroad4 жыл бұрын
Tyson Baller, it is narrower on the manual transmission setup.