Can you tell me the names of either of the two locks in this video and or where I can purchase them ? What store ? And measurements on them
@gregyancey51456 ай бұрын
I had the same unit only I couldn't insert the key into the lock to gain entry. Between drilling and prying the cabinet open it was pretty well junk.
@zacharyschnepp486010 ай бұрын
What’s up with that coil a big Spring doesn’t look right summer even working on that with a torch
@detroit0ninja10 ай бұрын
IKR, I have no idea what the previous owners did to this car. Rides fine, but a spring swap is probably in my future.
@dolzinnig Жыл бұрын
Thank you for sharing! This works way better than a cabinet without a key! Will be adding a hasp lock as well.
@donnylujan5464 Жыл бұрын
Thank you!
@Fatevad Жыл бұрын
what type of drill bit and size did you use to drill out the lock?
@danhofstetter8927 Жыл бұрын
Hi, I can't remember exactly, but I think I started out with 1/8" or 9/64", then worked my way up (1/8, 1/4, 3/8, 1/2 is usually what I do in these situations). The drill bits I used were from a DeWalt pilot point Titanium Nitride coated drill bit set, but really any high speed steel drill bits should work - the lock parts were not hardened.
@danhofstetter8927 Жыл бұрын
Actually, this video kzbin.info/www/bejne/rJCQZYhja8-drq8 shows you don't even need to drill it out, just clamp vise grips on and turn. Wish I had seen that before I did this :)
@reefing1022 Жыл бұрын
This is exactly what I was looking for. Thanks! I just bought two of these cabinets and the current locks are already seemed to start to sieze. Your tip on loosening the nut worked perfectly even on the key lock. I will definitely be buying these handles though as it would be way easier with a handle.
@anthony89612 жыл бұрын
Will this work on the stack on double door as well?
@danhofstetter89272 жыл бұрын
I'm not certain, but from photos online of model #GCDB-924, it appears to have a very similar lock setup. Please reply back here if you try it and it works.
@rickdramos77662 жыл бұрын
Awesome ty very much
@paulhorton81932 жыл бұрын
what is the second lock you installed?
@danhofstetter89272 жыл бұрын
Gatehouse 3.5-in Steel Keyed Hinge Hasp
@dongdong472 жыл бұрын
Great video, now it's so much better to see what youre doing. Thanks!
@RanaGillmotorcycles3 жыл бұрын
Thank you sir. My cabinet's lock broke within the first week of getting it from the store and i was looking for a video to replace the lock and your video helped a lot
@detroit0ninja3 жыл бұрын
I'm glad it helped!
@pdaaSk811 жыл бұрын
Oo and by the way, I'm having such a hard time unscrewing the bolts on both ends, I almost feel like I am going to break the linkage. Can you please make a more detailed video for us 500 riders
@aysesenakeskin55354 жыл бұрын
yes bob
@pdaaSk811 жыл бұрын
Hey whenever I shift from 1st to 2nd on my ninja 500, 70 percent of the time it will go into neutral. Will lower the shifter lever help my shifts fully engage properly? Thank you
@CptSlow897 жыл бұрын
What happened in the end?
@waffl67 жыл бұрын
Johnny Good I'm not that guy, but I can tell you that going into neutral between 1st and 2nd is typically just the result of not applying enough pressure to the shifter.