@@brandonpauling6631 mic couldn’t pick up all the bass correctly.

@@ryanbuenconsejo5306 battery in the trunk is OEM, I had a strobe light system.

Probably the ignition fuse.

@@joelcruz1292 100% did, double checked and everything but I’ve since removed the sub out of the Audi and did a new updated setup in my 01 Sequoia with a epicenter.

No, you can run the oem and aftermarket subwoofer at the same time since the oem subwoofer has its on amp from the aftermarket subwoofer. RCA is pure signal wire.

@@superrvolks One last question. Can I run the hilow converter from the wires on the two rear deck speakers into the subwoofer?

@@Realityvoidx I would look into your cars audio diagram to have a better understanding on where it would be best to pull signal from.

@@superrvolks I would love to have one, but there is little to no information for the 2024 audi rs3

@@Realityvoidx You don't need to add a hi-low converter if you use an amp that has the high level input controller onboard. If you look at the amp in this video, he has the High Level Input, he just didn't use it and went with the RCA. The problem there is that the Audi subwoofer signal already has 80 Watts going to it so now his amp has 80 Watts going into the input side which is not something you want to do as it may most likely damage that input on the amp and who knows what else.

It should work if the Q5 has the same/similar oem subwoofer setup, look up the audio diagram before anything.

Rotiform BLQ 5x112 19” +35 Offset, I also lowered the car as well, I have since got rid of the 19” and went to different style 18”

Right on man have a good one thank you.

Buy one?.. what product are we talking about exactly.

I know I’ve said this for a while now, but I will be having a video coming out showcasing how to install strobe lights in any vehicle. I don’t know when it’ll be as I’m in the middle of moving.

@@superrvolkshuh?

Yup

You’ll have to tap into the radio for rca, there’s a way to do it with the amplifier as well, I highly recommend looking into the audio diagram and seeing what you can work with before making cuts.

Yes, I used red as positive. I no longer use the amplifier shown on the video but usually red is going to be your positive.

Also why did you bring a wire towards the front

bungee cord

@@superrvolks thanks

Yes, you can use any type of speaker wire

Strobe light kit, I have a video coming out once I’m done working on my Jetta for installation.

I do not have CarPlay, I use a Bluetooth device that connects to the Audio System in the glove box. My instagram is the best way to contact me @SuperrVolks

I would recommend fixing the issue, if you want to run the whole system off an aftermarket amp then it would have to deal with passing wiring from every speaker to the aftermarket amp. It’s complexed as it sounds and me personally I would just get the original amp for the speakers then do the sub setup aside from the original setup.

I would also double check to make sure it did indeed go out before you start to replace parts.

@superrvolks, thanks for replying. Would you know how I would check if the amp is bad?

@@0Unkn.own0 multimeter, test the voltage

@@0Unkn.own0 you’re free to hit me up on Instagram @superrvolks

Everything I’ve used in the video is in the description with a link to purchase the product/similar product.

Do you mean the strobe lights? If so I’ll have a video coming out soon on how to install them and where to get them. Stay tuned in 👍

@@superrvolks yes

OK that's fine. I would like to put some like this on my 2010 Audi A4 car. But I want a bulb model that fits my fog light

My apologies for the late response, contact me directly on Instagram and I’ll help you out. @SuperrVolks

If there isn’t a connection for the RCA you’ll have to do it from the radio going back, I recommend doing more research with the radio and wire diagram before cutting up anything. My apologies for the late response

So if you’re doing door, dash speaker replacement, do research and look into the audio diagram. It is possible but this video is purely on subwoofer connection. If I’m correct there’s about 8-12 different speakers ranging from low-mids and highs which is your tweeters in the B8 A4. My apologies for the late response

How shall i do it? Happen to me

Not a good tutorial at all really. Running a high level input into the amp low level input is not the correct way to do this. The best way is to send a full range signal to the amplifier that is converted to low level. Use the crossover in the amplifier to low pass the subwoofer. There are products made that can sum the signal from the factory amplifier to make a full range signal.

Well sorry to inform you brother of you get a proper amp if has high and low level inputs or sometimes have a switch under the rca cables to switch from weak signal and pre-amplified signals

@@lunastar-k3w The amp he is using has High Level Input, he just didn't use it. The amp comes with the plug for it. When he shows the amp with the input side, pause the video, you'll see the white female connector and to the right, the input level control. I bought a similar BOSS amp because it has this capability. The 1,000W to power a 10" Polk Audio. It arrives next week.

@@EndoQuantum I have a boss riot 1100 watt amp and iam aware of the high level input but it’s very noisy unless you ground the wire properly to the chassis you will get a static noise and I would say it’s still not as good as the Rca connections from personal experience im using it to power 2 Rockfordfrosgate 10 inch R1’s and they sound great with the Rca cables

Send me a message on Instagram @SuperrVolks

How did you get around this?

I would recommend looking into the audio diagram, doing research for the RCA wires. Most likely from the radio or amplifier, as mentioned do research before cutting into anything.

Yes, it should be in one of the timestamps.

Glad you got it figured it out!

stock sub* not amp my bad

This has nothing to do with the stock sub except tapping into the RCA signal. Only way is if you’re feeding the stock subwoofer more amps from the aftermarket amp. The stock subwoofer has a stock amp installed already for its power.

Yes

Get the right stuff and do it right the first time around is my opinion.

I’ll be working on my car again so I’ll make a video showcasing the strobe lights and how to connect them 👍

@@superrvolks thanks mate, can you please also leave a link to were I can buy it from. Thanks. I notice I think your rear lights flashing too

No updates

No but it wasn’t long till I realized the amp wasn’t any good. I since have upgraded to SIA from Sundown Audio

I would get a bungee cord and hook it onto the cargo hooks on each side

Only thing I wired from stock sub was the signal wire (RCA) to the amp which gives little to no power, all the RCA is doing is transmitting the signal from the stock sub to the amp. So if you wired it up exactly like that then it shouldn’t be happening if otherwise then I recommend wiring it like I mentioned on the video which is the same way I mentioned here.

@@superrvolks The stock sub has 80 watts power going to it from the stock amp. Wouldn't recommend using that unless you use the High Level Input of your BOSS amplifier or someone uses a line output converter before connecting audio to an amp. I noticed you used the RCA instead in your install.

You can find speaker wire on Amazon but make sure it’s OFC as it’ll have better quality.

You need remote wire to turn on the amplifier, I am using the OEM subwoofer signal for the sound not the OEM Amplifier signal. If you run it straight like you mentioned there’s a chance the amplifier will be on 24/7 draining the battery.

My sub has been randomly coming on and off and the sub only runs for one minute. I went through all the settings I’ve unplugged the wire to the sub several times. I don’t know if there’s a wire that isn’t fully connected to the amplifier but if somebody’s knows a lot about subs let me know 👍

@@drakewarren188 make sure you are using the correct gauge wiring and size for your amp along with the correct fuse rated for your amp.

@@drakewarren188 what amp you use and how you connected it? If speakers wires straight to amp RCA it can be a problem

Bro am here looking too