Handsome man

Shellac would have worked

If only those walls could talk, the stories they might tell...

Yikes! So glad your safe and your house is ok🙏

Greetings from Tucson. Happy to hear all are well. Winslow came through good too.

Hey buddy. Glad you are alright.

Glad to see that you’re home came out ok with only minor damage. Need to get rid of the trees mom will take them and the leaves for the goats. LOL 😊

Love It!

Thank you so much for the great video . He’s a smart little fella . ❤ Mom

I'm lucky that my Ranger floor and cage installation has hatches where the seats were. Hell no would I be hacking up my Ram C/V load floor.

My teardrops kitchen door is stuck. The lock inside broke away from the handle. Any ideas how I can fix it myself?

i dont get it ? how come you need a unheated converter when your running vaper anyway ? how are you triggering the filter lock

Rincon, do you have a diagram of your electrical? Yours is one of the better ones that ive seen.

What about the long pieces is that 22.5

7:10 - should have at least a dust mask.

Good video

What’s the name of glue products please

good video

Your hatch spar (the spar that you will attach the hatch hinge to) is how far from the bottom of your galley? 48" since it's the width of the luan?

You should have put it on the floor to roll out the bubbles, you need a very stable surface and your table looks undersized

It would be nice to know what county and Township this is in

So the outer walls are just glued to the inner walls, no fasteners? I need to replace the outer walls on my motorhome, and I'm very apprehensive about taking on such a huge project. Any input would be great.

I have the same van. It came with plywood over the top. And it was split like 2.5 foot and 1.5 foot. I bought bi mart plastic shelving. I think it said it was rated at 200lb per shelf. I put plywood on top of the 2.5 foot section and made a nice bench. I don't drive it much anymore as gas prices make me drive a small car. But, I always wondered about what was under the metal. Thank you. If i had your measurements, I would be cutting the aluminum today. I had a flat once and it was a pain to lower the tire, so I keep it in the back, wonder if I could fit it in one of these seat compartments? I carry a racing jack and like to change a tire fast, as you know lookie loos like to crash into you. I hate the lowering tire thing they have, especially if I were on a busy hwy. Thanks for the video. My van has been a bit of $$ for repairs, but overall, it gets great mpg for a van that acts like a truck. I even got 29 mpg with some tablets in the tank a friend gave me. I think i want to get a small trailer to see how she does with the loaded back suspension and radiator on the tranny. Great little camper van. I only wish I wasn't so tall so I could slouch in the back instead of just lying down.

When my high school was being rebuilt, someone did the very same thing. It caused half of the new auditorium burn down

Looks great! What kind of wood did you use for the bulk of the galley? Like the cabinets, countertop, bulkhead etc. Did you put any sort of protective coating on the wood?

That's a really good idea

Can you send me those measurements

Where do you get these particular regulators from? I'm going to switch my lawn equipment over one at a time and want to do it right the first time rather than destroy an engine. Or my shop 😄

Can you glue filing to foam?

Great to have you back on the air. Good thing the safety man wasn't there to see you installing header by yourself. But sometimes we have to make do!! Keep it coming.

Looks great 😊

How did you go with your doors, did the manufacturer fix the problem?

I put a huge trash bag well ahead and behind the door. I tuck it all the way under the mattress. Over that, I tuck a huge beach towel. I've never had the water leave the towel but it has leaked every time I've driven in the rain.

Whenever you’re fitting something that’s protecting something from weather, use a sealant with it, even a small bead of clear general silicon with the rubber seals. Nice setup mate 👍🏽

great video I to just did this to my 2000 ford explorer, like the metal guard the best hard to push in and hard to be cut with a knife mine fits in the window channel and squeezed the open end to fit snug atop the window didn't like the wide width so cut mine 2" wide less noticeable so when the window is rolled up it snugs up really tight and sturdy although the plastic is used in some of these videos I felt they were less secure and decided to use the metal one and man I'm glad I went with my instinct on this one🤔

how Rainproof is this?

I always put two coats of adhesive on the wood. The adhesive can really soak into the wood and give you an adhesive starved surface.

I recently picked up a 2017 Dodge Grand Caravan GT and removed the 2nd and 3rd row seats from it. I've used some thin plywood (3/32" x 48" x48" in the rear to make a hinged access panel to the storage area. The front area is about 2" lower than the rear but I've leveled a 48" x 72" sleeping platform with legs of different lengths and have about 16".5" high space underneath to the floor level with nothing built above the stock seat access at the front. So, I have lots of space and can still slide in a 4'x8' sheet of plywood if I take the platform out. That platform is made of heavy-duty plastic storage shelving and it can be removed in about a minute (and transferred to a tent, etc.). I'm very happy so far with the system I've worked out for camping. I like the C/V version but IIRC, the cargo vans lack all the remote door and rear hatch functions. With my GT version, it is great to be able to just push a button from the inside (and outside) to open the side doors and rear hatch, or start the vehicle remotely including from inside when in the back. Makes crawling out of bed easier when camping. Am I correct in assuming the C/V version only has manual doors and no remote start?

I personally dont like the look of the baseboard cut this way when bull nose corners are used. I would rather just standard 45 degree corners, and fill in the top void with a good job of caulk. I am a builder, and that is how i did my own house.

Hi how are you I hope you’re doing well, I noticed you put the fan above the door is there any particular reason why you put it there instead of in the middle? I guess it doesn’t really matter. Just wanted to ask you that question and I appreciate all your videos and the process that you went through to film all these videos I know it takes a lot of time so we really appreciate that. Thank you.

Did it work?

You know that is trespasing some have been shot doing that !!!

Great job

what track is that. or the channel? Amazon or something?

Just saw your latest short about your family addition. That's the way it usually happens! One starts with a small trailer then moves up to a little more room and comfort and soon you have a full RV. Nice to see you back on.

The rural ND school house my Mom attended is still standing, roof intact, but minus windows & doors, floor very rotten. ---This was special, thank-you.

Update ? How is your Ram tradesman C/V working out after 2 years after modification video…. I am considering one of these.

My dad's family is from North Dakota ( rolette) the Lunde family.

So sad we should be preserving these pieces of history.

Excellent job!