Hej Torben, har set din video et par gange. Jeg står med samme problem. Hvad kostede hele operationen i dele?
@torbenfunch993725 күн бұрын
Hej Det kostede lige omkring 2000kr Jeg købte strammerene fra INA, originale bolte til strammere og knasthjul og de 2 øverste små plastik kædeskinner originalt. Du skal så have et timing værktøj, som enten kan lejes eller købes. Jeg har et sæt liggende hvis det har interesse!
@Shootoncamera4 ай бұрын
Where did you get this cute animal?
@Shootoncamera4 ай бұрын
I want another video with this wonderful marten
@isharaudayantha638611 ай бұрын
Can you guys pls tell me how to connect volume control bose 5
@sepstersepster9297 Жыл бұрын
Thank's for taking the time to do this video regarding the pulley upgrade ,it was very helpfull ,and nice to watch . I did the upgrade recently aswell ,and also bought the Chinese / ebay pulley ,with the removal kit (wich is a must to get the old one off ) . The removal of the original pulley was fairly easy ,but the fitting of the new one not so much ...after heating the pulley in the oven 3 time's at 225 degrees celcius for almost an hour at each attempt ,i could not get the pulley to slide on ,until i took a gas torch and carefully heated the pulley for 5 minutes ,and that did the trick ....i decided to cool the pulley with compressed air ,just to be sure that the heat didnt damage any internal seals in the supercharger . And as mentioned in a previous post ,its better to buy a higher quality belt ,as the one that came with the ebay kit does't looked that great ( it might hold up very well ,but i dont won't to take a chance on this one ) Next thing is making a appointment with the tuner for a remap .
@carlomontenegro1238 Жыл бұрын
I have companion 5 with broken pods.. how can i bypass the ON switch of the controller to keep it open .. thanks
@YuchiR01 Жыл бұрын
Hello Would you please make a video make bose companion 5 work without control pod? I try many way but not success ( cut control pod cord and connect 1 2 7 ( red green gray)) … Btw any help with dual bass ? Thanks
@torbenfunch9937 Жыл бұрын
Hi Sorry but don't have a clue how to make them work without the control pod. Best regards.
@YuchiR01 Жыл бұрын
@@torbenfunch9937 ok thanks your reply, how do you think about mod with dual bass?
@MeganWyatt-uw8ki Жыл бұрын
0:58
@leighgate2 Жыл бұрын
I’m using them on my tv too. They sit right next to my RCN ARRIS router which has 2 USB ports on back. I’ve plugged it into one of the ports and the light stays green even when tv is off. Haven’t had any problems so far.
@maximilianorandolph Жыл бұрын
Hi buddy ...is posible conect to my galaxy ultra usb-c with usb port pc???
@torbenfunch9937 Жыл бұрын
Hi I have no clue? I guess you willbe able to if you get an adaptor.
@Around-The-Verse Жыл бұрын
Weird question but where did you buy blue speedo?
@torbenfunch9937 Жыл бұрын
I disassembled the instrument and swaped the diodes!
@martinlucero9594 Жыл бұрын
EXCELENT VIDEO!! THANKS FOR ALL YOUR INFORMATION!!!
@stanblakey9669 Жыл бұрын
Works amazing! Thanks for your explanation.
@captaincool2077 Жыл бұрын
Sir i don't have control pod of bose companion 5 how do i bypass please help me
@sergeflusman7801 Жыл бұрын
Hello, Thank you for this video and comments. I have the same rattle problem on my 2009 A6 V6 TFSI. I will try to change the 2 top tensioners. I bought the engine timing tools. By removing the compressor, is it accessible? Do you need to remove the catalytic converters? For parts, I saw in another video that you bought INA tensioners? I hesitate to take those at Audi which are very expensive. the small slides at the top were not broken? Has the cold start rattle problem ever returned after replacing the tensioners? Thank you for your answers.
@torbenfunch9937 Жыл бұрын
Hi Thank you for watching my video! The removal of the compresor is nessecery but it is very easy and tales only about 20min When it is of then change the oil on the gear! On my car removeval of the catalyst converters was not needed but I read on Audizine that some S4 and S5 with same engine has a shield for the secundary air valves wich is not possible to remove with the catalyst converters not removed... The tensioners from INA did the job and there was no cold start rattle afterwards! The small chain guides you will need to get geniue bud they are only $4 each. Also you need ti buy new bolts for the tensioners ant the cam spokets! If you are happy with the car and want to keep it for a long time i would suggest that you chance the valve lifters and rollers. I didn't and I was struggling with sporadic ignotion fault on one cylinder. It turné out to be the rollers and lifters so I had to do the cam timing twice😂
@lixyy7085 Жыл бұрын
Flotte fisk, gode omgivelser Nyd turen!
@lixyy7085 Жыл бұрын
lorte nisse
@mgonzi2 жыл бұрын
Did it it works
@mgonzi2 жыл бұрын
Thanks
@torbenfunch99372 жыл бұрын
Yes it works!
@msika9332 жыл бұрын
hello friend Before you replaced did you get any code with a fault number?
@torbenfunch99372 жыл бұрын
Hi No there was no fault codes regarding the timing. But I had faultcodes for misfire on one cylinder. It gave me some headache! It turned out to be the rocker/rollers for the hydraulic lifters! If you deside to change the cam tensioners then I would suggest to do the rolers and lifters at the same time. They are not that expensive. You will need new bolts for the cam covers though...
@msika9332 жыл бұрын
@@torbenfunch9937 thanks man, you change only the tensioners? i have the same noise and i dont get a any fault code, but i check all the 6 cylinder, and i get 1 misfire counter on the cylinder 2, i think its a same problem :(
@torbenfunch99372 жыл бұрын
@@msika933 yes I only changed the tensioners!
@Samil1012 жыл бұрын
you went to Mac to learn how to use Bose? so you took it apart and hacked it to do some dumb shit? You’re an idiot there is a clearly Marked input on the volume controller to plug in whatever you want.
@kusubudo2 жыл бұрын
Short SENSOR pin (3.3V) and RMTGND pin to generate a softstart to reset USB controller to wake up system.
@mvfernando Жыл бұрын
Wich is the pin of RMTGND and which one is the sensor?
@david.pitzler Жыл бұрын
@@mvfernando I just looked in the circuit diagram. And it seems its pins 6 and 9, if you look from the back at the connectors and count top-left=1 bottom-right=10. But I cant confirm if this works, since I dont have any jumper cables on hand.
@hjaniel44282 жыл бұрын
👍
@johnjagtiani20972 жыл бұрын
Hi - very formative video and comments. I have the same system, but I do not have the control pod. what is the easiest way to bypass need of the control pod all together if all I am doing is connecting to computer through USB (I can control volume on computer I suppose). Would like to bypass control pod plug in , keep fully on and full volume at all times and control through USB. any help appreciated!
@carlomontenegro1238 Жыл бұрын
Bro i have the same problem as yours .. i have broken volume controller pod, what did you do to keep it On and in max volume to maximize the sound ..
@inkyfiny8883 жыл бұрын
I bought that same product also and got it installed now. Here is some notes: -For A6 c6 and this removal tool, there is no need to put car on to the service mode. Just take off the bonnet lock and the air intake duct. Installation process itself takes about 1,5 hour, if the new pulley fits on at the first try. - There is very limited room to work. Make sure you have LONG and slim 16mm wrench to loose the belt tensioner. - Loose the belt tensioner and put the locking pin to hold it still. This makes installation process way more easier. I took video with my phone from the engine bay to locate the locking pin hole. - Pulley removal tool worked fine. Make sure you align it straight towards axle. I made mistake here and destroyed the threading from tip of the tool. - Make sure the new pulley wheel is heated at least 200-250c when you install it on the axle. Pulley wheel cools down really fast, so you must have some sort of oven right next to the car. I utilized an airfryer for heating it to 200c for 1 hour and after that I used heat gun for 5min to ensure needed installation temperature. - This particular pulley from Aliexpress seems to be more tight fit than OEM. I tried to measure it and difference seems to be around <0.1mm. I used fine sand paper rolled on drill bit to carefully hone the center hole bigger. If you take too much, use e.g. Loctite 648 to secure the connection....DO NOT weld it on or you might screw up ECU and other electrical components. - Push the pulley wheel all way back and use pressurized air to cool the wheel and the SC-axle, otherwise high temperature could damage the oil sealing of the SC. - Installation process is pretty straightforward, easiest way to put the new belt on is to slip the belt on to the "opposite way" guide last. - And most importantly: Please consider buying higher quality pulley to make your life easier... Tool was ok, but tolerances for shrink-fit are too precise for Chinese low quality production. Worst case scenario the center hole would bee too larger and the pulley wheel slips off when your engine is running.
@torbenfunch99373 жыл бұрын
I did the same thing with sand paper and drill-bit! To be sure the pulley wouldn´t get loose I spot welded the pulley wheel on to the SC axle. Note if you use the belt that comes with the set then keep an eye on it! It is wery bad quality and mine only lastet 4000km!
@inkyfiny8883 жыл бұрын
@@torbenfunch9937 Thanks for the heads up. I will replace it asap.
@inkyfiny8883 жыл бұрын
@@torbenfunch9937 Where did you buy the replace belt? Can you share a link please?
@torbenfunch99373 жыл бұрын
@@inkyfiny888 Every sparepart shop has them! 7PK1270 is the number
@inkyfiny8883 жыл бұрын
@@torbenfunch9937 So it is similar length as original? Anyway, I ordered SKF VKMV 7PK1270 right away. Did you have any other problems/mentionable things after going for the stage2?
@pedrovelazquez61663 жыл бұрын
Add a diode to the coil of the relay
@torbenfunch99373 жыл бұрын
To prevent the white noise?
@pedrovelazquez61662 жыл бұрын
@@torbenfunch9937 to prevent backwards current from the coil
@bez7503 жыл бұрын
How much power did it make my friend?
@charleykeate20603 жыл бұрын
190 at 0.9 boost
@MeganWyatt-uw8ki Жыл бұрын
My makes 3 hrp
@dsevwrh3 жыл бұрын
How long did ypu heat it?😁
@torbenfunch99373 жыл бұрын
About 30min
@dsevwrh3 жыл бұрын
Är det med triptpnic lådan?
@torbenfunch99373 жыл бұрын
My Swedish is not 100% up to date but if you ask me if the car is a Tiptronic then yes!
@dsevwrh3 жыл бұрын
@@torbenfunch9937 okej the english it is 👌😀 thanks for the reply but I have som Q if thats ok? I have a 2010 and wanna do this but when I search on apr and revo it say that this is not compatible woth this transmission, and I dont k ow why? But how did ypu do it?
@torbenfunch99373 жыл бұрын
@@dsevwrh it works perfectly! I don't see why you have got that information?
@dsevwrh3 жыл бұрын
@@torbenfunch9937 if I go on to apr site and ecen revo its in the texts, this text is from Revos site NOTE: Stage1+ software and Supercharger Pulley Upgrade is not compatible with 3.0TFSI vehicles using a 6speed Tiptronic transmission (As found in some early none 'S' model vehicles, speak to your Revo dealer if you are unsure of the transmission in your vehicle).
@torbenfunch99373 жыл бұрын
@@dsevwrh I have the 6speed Tiptronic converter gearbox! It works like a charn💪 I had the transmission tuned as well. The clutch pressure in "S" mode is tweeked and the torque limit is raised! I think the dyno sheed is shown in the video in the end?
@jj-tq4hx3 жыл бұрын
Great video and helpful! Can this be done by just removing the Supercharger instead of the front bumper? Wouldn't it be easier?
@torbenfunch99373 жыл бұрын
I haven't removed the front bumper for the installation. If you remove the supercharger it would be much easier and then I would suggest you also change the supercharger oil at the same time!
@jj-tq4hx3 жыл бұрын
@@torbenfunch9937 Ok thanks! That's a great idea to change the oil of the Supercharger.
@johnlam78543 жыл бұрын
I got the same srad 😊
@ПетрМирошкин-м7е3 жыл бұрын
это скорее топливная форсунка....
@dusankubis58443 жыл бұрын
Mine is on the same site... Did u have to pull engine out I read somewhere you can do it with engine I place on that side ( passenger side in uk)
@torbenfunch99373 жыл бұрын
Hi No I did not pull the engine! There is room enough to change them with the engine in!
@dusankubis58443 жыл бұрын
@@torbenfunch9937 thanx for info boss...any chance you can give me heads up on any special tools (timing kit?) needed , did you use special sealant on cover when put back together also any chance on any photos , video of your work ?
@torbenfunch99373 жыл бұрын
@@dusankubis5844 I dont have a video of how I changed the tensinors but I have made a video with pictures of the timing tools and more...kzbin.info/www/bejne/omPTdmCvqdxqn9E I can reccomend you to also watch this video, not the same engine but the procedure is the same. kzbin.info/www/bejne/nKGrgImves-akJo
@dusankubis58443 жыл бұрын
@@torbenfunch9937 top man and thank you
@torbenfunch99373 жыл бұрын
@@dusankubis5844 you are welcome 👍
@zxc1423m3 жыл бұрын
My bose companion 3 series 11 problem when full blast the bass. The sound go out and no more sound anymore . Your method able to solve this problem.
@yerin12023 жыл бұрын
Ask a question. I bought the same product as yours, but it doesn't work even if I put it in an oven capable of 230 degrees Celsius for 40 minutes. Is there a way?
@yerin12023 жыл бұрын
The supercharger pulley was heated in an oven at 230 degrees for 40 minutes. And when I try to put it on, it doesn't fit. Does not enter.
@yerin12023 жыл бұрын
Cut a thin of 0.7mm?
@torbenfunch99373 жыл бұрын
So you can´t get the new pulley on to the supercharger? I had the same problem and that is why i did not show it in the video as it was not a pretty sight seeing me struggle... What I did was: I added a pice of fine sandpaper(grain 400) on to a drill and rolled in on to the same size as the hole on the pulley. Carefully i used it to sand the hole in the pulley. Be carefull as this is a press fitt. You will not take of to much!!!!!! After that i heated the oven again and then it worked! I did a little trick just to make sure it stayed there. I gave it a small spotweld at the corner on the supercharger axle...
@yerin12023 жыл бұрын
@@torbenfunch9937 There is a company that does CNC lathe processing nearby. How many millimeters should I cut? It's really difficult.
@wawawa49573 жыл бұрын
@@yerin1202 Did you successfully install the pulley?
@ivanstory69863 жыл бұрын
Mine does the same thing. Was there any damage to the timing components as a result of the chain slap with the old tensioner? I am actually going to try changing the oil pressure check valves before doing the tensioner to see if there is an improvement.
@torbenfunch99373 жыл бұрын
Good idea with oil pressure test but I don't think you will find it too low. It is caused by oil draining from the tensioners. From what I could see there were no damage to other timing components.
@ivanstory69863 жыл бұрын
@@torbenfunch9937 Thanks!
@bradbushman22972 жыл бұрын
@torben , he is referring to the valves that keep oil in the heads.
@robsonf66834 ай бұрын
Were you able to replace tensioner on car?
@ronniek74263 жыл бұрын
You do know there was and still is a simpler way, I am an award-winning audio artist, i have 2 Bose Companion 5 systems. 1 for my computer setup, where I use it to play tracks recorded in the recording studio, & the other is for my cinema sound system, of all the computer systems I have tried these are by far the best sounding, for the cinema I have it all wired up in fiber, I did need to buy a fiber to 1/8 inch out to input in the line in ... a prozar 192khz DAC converter box (see images in google search) that uses a 5v power, for about $20 on WISH as they did or still don't sell in North America, only in China, now you can get them for about $40-$50 in Walmart.. Amazon etc... Good luck
@BJNeutral3 жыл бұрын
Hej, how many kilometers did your car have when you cleaned the intake valves?
@torbenfunch99373 жыл бұрын
282.000km I have no idea if it had been done before? But it was about time!
@BJNeutral3 жыл бұрын
@@torbenfunch9937 It really was! Wish you a worry-free ride, this engine should be strong and last long after intake valve clean and timing chain guides :)
@torbenfunch99373 жыл бұрын
@@BJNeutral I sure hope it doesn't give me any problems 😀 I have planned to change the waterpump, thermostat and upgrade the pvc valve.
@torbenfunch99373 жыл бұрын
I have uploaded a video more showing the tensioners and after I changed them. kzbin.info/www/bejne/omPTdmCvqdxqn9E
@yerin12023 жыл бұрын
Fixed it? Wasn't it the noise of the PCV valve?
@torbenfunch99373 жыл бұрын
Yes the cam chain tensioner was the problem!
@raghav16043 жыл бұрын
what if i just short 1 and 4 , will it always stay on when i switch on the power?
@FiveStonesChurchWaxhaw2 жыл бұрын
I tried this and got no sound from the system and the lights on the control pod was not on. I took the wire connecting 1 & 4 off and it worked again, so think I will try the Apple device... want to have the speakers on all the time. Thanks.
@allancnc3 жыл бұрын
Det ser jo godt og sparer sikkert en for en masse bøvl lige pludselig. Hvad koster sådan en omgang hos dig?
@yerin12023 жыл бұрын
Great video~!! Where did you buy the pulley removal tool?
@torbenfunch99373 жыл бұрын
I got it from Aliexpress
@yerin12023 жыл бұрын
@@torbenfunch9937 Thanks for the answer. Where to buy Supercharger Pulley? ECS Tuning?
@torbenfunch99373 жыл бұрын
@@yerin1202 I got a complete kit here: www.aliexpress.com/item/32974928746.html?spm=a2g0s.9042311.0.0.27424c4dpUGCpT The tuning was done localy on a dyno. You will notis a diffrence just by installing the pulley in the low rpms and not tune the ECU but after the tuning it is a complete diffrent car! Strong as hell!
@inkyfiny8883 жыл бұрын
@@torbenfunch9937 Can you recommend that kit? Was the tool good and has the pulley worked so far (no slipping etc.)?
@torbenfunch99373 жыл бұрын
@@inkyfiny888 yes it worked perfectly and I have had no problems with it! As you may be able to see on the video I have cut a thin piece of 0,7mm and added to minimize the play in the tool.
@Goooriiii3 жыл бұрын
i have the same problem :) I think the change the upper cam chain tensioner in both sides is fix it.
@torbenfunch99373 жыл бұрын
I did change the tensioners and it was that!
@wawawa49573 жыл бұрын
Great! I have a supercharger pulley that I haven't installed yet, but I was just thinking it would be a pain to work with after I put it in the service position. This is easy and nice. Does this work take about an hour or so?
@torbenfunch99373 жыл бұрын
Glad the video can help! Sorry for not showing the installation. Make sure the axel is clean, cold and the new pulley is straight from the oven! I would say the whole project is about 1- 1,5 hour
@arturmakarevic28634 жыл бұрын
I think is sound of timing chain tensioner or chain!
@torbenfunch99374 жыл бұрын
It was the upper tensioner for the driver's side! kzbin.info/www/bejne/omPTdmCvqdxqn9E
@ThatAfricanGuy4 жыл бұрын
Well done my friend! I liked the parts where you picked the dried fruits and nuts haha. This job can be exhausting so you do need energy. Beautiful garage 👍🏽
@torbenfunch99374 жыл бұрын
That is not driet fruits but Harribo candy😜 I made a nozzle from a 7mm cupper tube!
@ThatAfricanGuy4 жыл бұрын
@@torbenfunch9937 Super cool 😁
@ion_q4 жыл бұрын
All of a sudden, when ever i plug AUX into headphone jack on the bose control knob, it goes orange & refuses to output to my mixer / or headphones?!?!?
@drlecter9024 жыл бұрын
You can convert your bose into a Bluetooth speaker. Lots of bluetooth device on line and eBay
@pabsgabs4 жыл бұрын
Good work! Thanks for sharing.
@tomc26814 жыл бұрын
Omg hvor er han cute
@JyttesTrailCamera4 жыл бұрын
Han er bedårende :) Jeg går ud fra at det er Miew, den du fødte up sidste år? Interessant at han er blevet hos jer, nu han er voksen. Jeg håber du vil uploade mere film med ham. Vores (vildtlevende) par har netop præsenteret deres 10 uger gamle hvalpe fra dette år.