Where did you get the spacer you used between the speed feed head and the Stihl gearbox?

Why do this? Stihls grease tubes literally screw in to port

a hammer lol...there are threads on there my man

If it says fuel, it's brushless just so you guys are aware

Good simple video, but you’re wasting lots of it. You don’t need to coat the entire stump. Just the edges.

Yeah, do you know the difference between a door handle and a latch mechanism?

Where did you get that spring kit

Where to find that spacer

Have you tried this on a fs70 or 55 ??

You don’t have to twist the bottom if you hold the bottom still and twist the top it will keep your string from wrapping around the shaft as your restringing

That won't work anymore. The heads have those gear groves in them.

I always take my guards off. That cutter on them will literally eat your string up everytime you tap it onto the ground. Also, a friendly tip. If you want to keep a lot of string from coming out just stretch your spring some. 💯

could seriously do with out the background music wtf

Thank u very much for making this video!!! It made changing my door handle a breeze and I’ve been putting it off dreading it for a week now , lol. This video. Helped me and u took time to show and explain each step , thank you !!!

Well what's the best way to unthaw the e47 pump

Question for you. My plow will not angle side to side. It's has brand new hydraulics and fluid. I can hear the pump or motor working but it won't turn either way

Great helpful video , well explained and concise. Thank you!

Thanks for the video !! Worked on my blower. Kept me from buying a new won. 🤣🤣

Mission complete! Thanks!!🖤

Are you still using it?

Thanks a lot video very helpful u guys are the best.

Where does the loose end of the rod connect at the bottom of the door?

Thank you for this video. I was able to replace my mom's car's door handle, saving a couple hundred dollars. Unfortunately, it was unclear how you removed the black cable so I wasn't able to completely remove the door card and had to leave it attached. But so thankful for your video!

I've watched a couple of these videos. Yours has the best lighting & camera work. Also the "little details" regarding the insulation removal is appreciated. Thank you for posting this.

Why not do 45’s?

Have you ever change the cable on a echo blower PB 250 Excelerator cable for the carburetor

Thanks for doing these. Very helpful.

what size scocket did you use ?

Wow💥 thank you So' much! I'm having this exact' problem, with the same model blower . 🛠

I had a model older than this one that I love. My sister has difficulty with tools that are too heavy and she actually loved mine and found it easy to use kzbin.infoUgkx_rBCFuDW1zD6blTGhLkvAkxU657uR_lG . This is a newer model but was even lighter which she really appreciates. She enjoys it and I no longer have to go to her house to trim as she can handle it fine. Haven't used it enough to comment on the battery life but lithium batteries last longer than the old style. Being cordless makes it easy to trim the far edges of the property. The entire yard can be trimmed with one charged battery.

Do it even easier, fit a needle grease injector to your grease gun. Packs the gears full.

Reaults?

So how do you know when to stop pumping grease? Or how many pumps do you do? With the tube grease from Stihl I kno when it’s full with resistance as I squeeze the tube

That's pack deal are not fuel ones

Just started my collection of these tools today brought the m18 impact fuel gen 4 with 5ah battery case and charger for 190 uk pounds

I don't have any problem doing it the recorded mended way I spent a lot money on my weedeater years ago so I can understand screw a fitting and use the right greas easy maintance

How do you know when the proper amount of grease has been inserted?

Well, there are 2 adjustable mixture screws on that style carb. You only adjusted the high speed screw, and while that can fix it, often you need to balance it out with the idle/low speed screw. It runs down the inside of the throttle barrel, located 90° from the side screw you found under the purge bulb. There is a cover over this part on top that covers the throttle linkage, remove that, and looking down at top of carb you see the hole inside the shaft with a nut on the outside. It also has a plastic plug from the factory. Aftermarket carbs usually omit them. This is the low speed/idle circuit screw. Also have to coordinate the idle speed with the low speed adjustment, keep it at idle speed when adjusting the mix. ALSO, MANY times bogging like this where it just refuses to rev up is due to a plugged muffler spark screen, and/or carbon built up behind the muffler in the exhaust port! To clean out, remove the muffler run the piston to the bottom, and carefully scrape out the carbon to the edge of the port, blow out the cylinder from the spark plug hole before replacing the muffler. The screens are serviced without pulling the muffler, behind the small plate with a screw on the face by the outlet. Use a torch to burn the carbon out, or soak In Sea foam, or laquer thinner, etc. In this video, that PB250 was not revving like it should, still needs one or more of the above mentioned. 👍🙏

Thank you very much for the easy to use/watch video. Six month of procrastination for a one hour job. Just like you and your video showed. Thanks again.

it a good thought , i don't like this idea, and you should of tap over wood or plastic not a hammer on top of the fitting

Bad advise all around. Sorry but you said to comment.

Good job

thanks for the tip about saving the bushing from the stihl head, my fs 131 would not work with the ones that were sent

I use a flush method, take out the plug, flush the old grease out with a degreaser. Then put new grease in with the original method.

WHAT NOT TO DO!!

Thank you for saving me $435.34 I appreciate it

Thanks for the video. I found it useful, but the part where you disconnected the cable leading to the interior latch wasn't clear; it looked like you jumped over it in the edit. I wound up just leaving the cable attached and leaned the door card against the door so I could complete the job. Surprisingly, I didn't break any of the plastic tabs removing the door card.

Could you possibly get any lazier with that tiny yard? A riding mower? Really?

There's a short clip of a Motorcycle that is turned Into A ride on tiller somewhere on youtube

Thanks for the video. I got this done in 30 minutes. Only broke 1 clip