Arctic Air LLC

Пікірлер

@come_on_now Ай бұрын

Can we stop w this nonsense yet? Yalls nuts! DC compressors are a damned joke and only a communist would sell that shit.

@اغانيالزمنالجميل-ع6ز Ай бұрын

Where can I get the full video?

@OMHSega Ай бұрын

@jaymaca Ай бұрын

What kinds of psc motor and brand?

@ArcticairLLC Ай бұрын

US Motors 3/4 HP

@victork3397 2 ай бұрын

I like that you took the time to sharpie the date you installed the motor

@ucminhngo5072 2 ай бұрын

Just need replace Control motor module

@victork3397 2 ай бұрын

They’re not always available separately

@robertpearl2369 3 ай бұрын

My Trane ECM blower is doing this same thing.

@lostdud 3 ай бұрын

Seems like a waste of copper? But also important to drain and wouldn't break like pvc might I guess

@championx1 4 ай бұрын

Does it go 20 mph as advertised.

@plumber1874 4 ай бұрын

No not channel locks

@mirkoobradovic3426 5 ай бұрын

But how did you get it out?

@roncooke8723 8 ай бұрын

Before you buy a new motor, try bending the fins away from the grated housing. That was all I had to do. I had the same exact problem. Just bend the fins back to where they belong. They must be weak and affected by the heat.

@arengineeringyasirfazalcoolone 10 ай бұрын

Good work 👍

@hotfeva9843 11 ай бұрын

Now install an ionizer and 2 uvs

@austrianpainterinhiding88 11 ай бұрын

Where can I get the full conference? Looks very informative.

@austrianpainterinhiding88 11 ай бұрын

I go out to the woods or sit by the creek whenever I can. It's great!

@dcmoor4662 Жыл бұрын

What would cause the idm to run continuously?

@ArcticairLLC Жыл бұрын

An open high limit switch, open roll out switch, cracked solder on the control board, plugged air filter , maybe a bad motor

@ewong8505 Жыл бұрын

Promo sm 😆

@vertihvost7675 Жыл бұрын

How did that happen?

@ArcticairLLC Жыл бұрын

Maybe just a defective blower wheel

@TheAmtrack69 Жыл бұрын

I wonder if they will need their ductwork cleaned?

@Creativetoursflorida Жыл бұрын

Thank you ! Great Video Common Problem

@JohnstonPettigrew Жыл бұрын

You seem very 🤔.....

@Flirken2975 Жыл бұрын

Excellent job

@ArcticairLLC Жыл бұрын

Thank you very much!

@raymedinaj8055 Жыл бұрын

The replacement not have a ground? I only saw 2 wires the old one had 3

@ArcticairLLC Жыл бұрын

The leak was 100% fixed for very cheap. Thanks for commenting.

@KninskaKapija Жыл бұрын

Haha just because you don’t hear it doesn’t mean leak if fox

@blakehollingsworth839 Жыл бұрын

No need to check the voltage coming from the board to the inducer motor lol it’s obviously bad

@JonathonYoppini Жыл бұрын

What size vacuum line is needed? Thank you for the video, very informative

@raymedinaj8055 Жыл бұрын

3/16

@KAOCOFOUNDERCAJR Жыл бұрын

Like fr🤣🤣🤣

@varonicarichardson8731 Жыл бұрын

How tall is the rider?

@ArcticairLLC Жыл бұрын

5 ft

@Whyru_lookinhere Жыл бұрын

Bro ik where this is

@Whyru_lookinhere Жыл бұрын

Bakers Feild

@Whyru_lookinhere Жыл бұрын

I’ve been here

@danielsandoval9204 Жыл бұрын

That panel that's infront of the inducer motor did you leave the gas line on and just push it to the side or did you disconnect it?

@raymedinaj8055 Жыл бұрын

I unscrewed the top all across the top of unit it came up enough to pull out the panel and slide one way or the other. But mine had hard pipe line all the way . But if have flexible gas line you should have more play.

@danielsandoval9204 Жыл бұрын

Thank you for video

@robertcoggin3366 2 жыл бұрын

You get a thumbs up for the killer outro music too

@sandrarichardson2713 2 жыл бұрын

I guess I was expecting to see how to get that blower out of there safely, what cleaner was used to really cut the sticky grime and about the same thing on the evaporator coil...how did you get into like that and what kind of cleaner is safe for the coil, etc. Not really any useful information here for me.

@uxwbill 2 жыл бұрын

It's kind of a wonder that blower motor didn't conk out. Do they not run any filters in that system?

@ArcticairLLC 2 жыл бұрын

It probably shortened the motors life being that dirty. The filter was brand new so it might’ve not had a filter at all for 5 years. Thanks for watching.

@watchfuleye4082 2 жыл бұрын

Not sure why you checked multiple ground locations on the ac. Would it not make more sense to check ground at the chassis grounding lug and only check it one time? Good video, thank you.

@biblebloopers946 2 жыл бұрын

How did the evap coil look?

@ArcticairLLC 2 жыл бұрын

The evap coil didn’t look all that bad, I thought it was going to be plugged up like the blower wheel. It took 5 min to lift the top off and spray it with the hose and also clear the condensate pan.

@bobboscarato1313 2 жыл бұрын

Sometimes the wire terminal is corroded or broken and you won't see indication in ohm meter! Pull top off and remove plastic terminal cover.

@bobboscarato1313 2 жыл бұрын

He just got to what I just commented!

@ArcticairLLC 2 жыл бұрын

Yes, there are some techs that are quick to condemn a compressor without checking the terminals first

@rubenguzman6144 2 жыл бұрын

Just curious why you didn’t check your windings when you had the wires were off after checking for a short you would’ve saw you either had an open winding or bad wire to compressor, start wire could’ve been touching common and shorted out, good job

@ArcticairLLC 2 жыл бұрын

I started checking the windings at 3:07 but didn’t follow thru, it’s a good idea to check the terminals first before resetting the breaker. I’ll do that next time. Thanks for watching.

@mohammadabid1222 2 жыл бұрын

Is that a variable speed switch and what kind . Can i use a variable speed switch instead of the toggle switch to control the speed of the exhaust . My exhaust i believe is 1 hp thansk

@_GandalfTheGrey_ 2 жыл бұрын

How did you know it was a bad contractor exactly? I’m new to electrical and missed the explanation.

@dave928 2 жыл бұрын

you couldn't even move the cap over or down 1" so you're not covering the rotation sticker? hack job by a hack tech.

@ArcticairLLC 2 жыл бұрын

Anybody that doesn’t know the rotation of a blower wheel just by looking at the blower housing has no business taking the panel off, not all units have “rotation stickers”

@lees.4084 Жыл бұрын

It's not like you can't look at the rotation sticker and still figure it out.

@octane4life683 2 жыл бұрын

This sacrifices efficiency. If the customers wanted this done I guess that's okay.

@ArcticairLLC 2 жыл бұрын

They were selling the house so yea they were ok with it.

@lees.4084 Жыл бұрын

And how much efficiency would it really sacrifice? Enough to ever compensate for the cost of the ecm motor?

@octane4life683 Жыл бұрын

@@lees.4084 There's ecms that are $200.

@lees.4084 Жыл бұрын

@Octane4Life And there's ECMs that are well over $200... And not all PCM are variable speed. My X13 is fixed speed. Speed can only be adjusted by changing the jumper terminal on the motor. But let's say you replace a fixed speed $200 ECM with a PSC that costs $100. How long til the efficiency savings allow you to break even? I'm considering a PSC swap because I'm on my 3rd motor module in the past 2 years. Just the correct module is $200+ each, and takes nearly a week to arrive. My motor spins freely, and passes the resistance checks. I even have one of the inline surge protectors installed, and still have module failures. I'm considering just buying a PSC, and next time the ECM flakes out, swap over, and hopefully not have to worry about it again for a long time.

@octane4life683 Жыл бұрын

@@lees.4084 Yes there's 3 types of ECM. Constant airflow (variable speed) constant torque ( x13) and constant speed (inducers and condenser fan ecms). If people have these things, you gotta pay to play.

@octane4life683 2 жыл бұрын

Did you even bother to check the heat exchanger?

@ArcticairLLC 2 жыл бұрын

Yes, a little surface rust but no holes or cracks.

@octane4life683 2 жыл бұрын

@@ArcticairLLC them tubulars can take some abuse for sure

@babyking5763 2 жыл бұрын

Captiveaire is top of the line shit.

@edlauren9434 2 жыл бұрын

I’ve started doing the same last year. Had a Nordine package that needed PCM motor that was kind of unique and only OEM could be a direct replacement. It was 2-2.5 weeks waiting time for that motor to arrive plus ~$600. So, installed PSC for $90, plus a contactor. It’s been a year and that store owner is happy with his HVAC operation. Now, I do the same swaps almost everytime when I see bad ECM motor.

@yamilethtl119 2 жыл бұрын

Para dónde de ve de jirar par.adentro o fuera

@pelonrecords 2 жыл бұрын

Part number?? It's the same kind I need

@ArcticairLLC 2 жыл бұрын

Pause video at 1:05, part number on the box or go to Repairclinic.com and type in the units model number.

@gordon985 2 жыл бұрын

Artic air my friend had a box fan by country air it kept you cool but smelled like cow poo I had a artic air fan it blew even colder air but smelled like penguin poo.

@ArcticairLLC Жыл бұрын

Lol

Ең жақсы KZbin

Пікірлер