Is the positive still connected by

It's your alignment. Nothing to do with the tires. It's your truck

Thanks great video

You be lucky if you can obtain any battery acid for sale nowadays. Its only for commercial companies, no sale to general public. Some can get through 'cooking it off ' drain cleaner solutions? But easiest is just recovery from 'old batteries', filter out gunk and reuse these.😮

I need to fix an exhaust bracket. Will the heat destroy the bond? It gets super hot as it is a 1000cc bike

He does not know how to plow. I would of had that done in 2 minutes and it would of been cleaner than that. Wow

use cider vinegar for heartburn, not baking soda. the stomach is supposed to be acidic, now if you drink alkaline backing soda and yes it will temporarily get rid of the symptoms but will not fix the route of the cause. one tablespoon of cider vinegar to a pint of water sip before and after fatty or processed foods and it will help digest the food if that doesn't work you may have a trapped nerve from your spine that is stopping the upper sphincter from closing fully, symptoms will be neck pain and or pain between the shoulderblades in your spine along with acid reflux, GURD, heartburn all the same thing but causes can vary. mostly caused by eating junk food, sugar and soda pop, sweets, crisps, bread,

I did this on my Zx6r motorcycle. Been holding up great for 4 months.

Thanks for your time Bob,I appreciate your knowledge and your time. Stay blessed .

Glue😂 then soda, then glue one more time after soda, min. And then held together with pressure and that works the best in my experience!, thanks!!

This worked for my car. Thank you for the video. 0:19

This worked for my car. Thank you for the video.

Use a red butt connector crimp a piece of copper wire or small screw in it. Drop of super glue on the other end slide it on and you’re good to go.

Good video, thx. 👍

Nice presentation! I wonder if sanded aluminum (powder) could be added to the baking soda?

Should be titled “how to be all over the place and almost drive through the garage driveway plowing”

W😊W GREAT TIP 👍🏻

Nice

just rinse with distilled water. If rinsing would work, and that is hit or miss, then that would do it, then put the right mix of acid and distilled water back into it. It's hit & miss since you can't see between the anodes and cathodes to see just how bad it is.

So why does my spring always pop off

I run O'Reilly 5W-30 convention oil in my 09 Tacoma, my truck run smooth just like the oil change from Toyota dealership . Good oil I will keep using O'Reilly oil.

You’re right helped me start my car

Thank you for being understandable and to the point.

Thank you for your video, very helpful. Literally the problem I'm having. 👍💙

Thank life saver !!!

I'd be interested to see cotton impregnated with baking soda. I think the fibrous nature of the cotton would aid the baking soda in tinsel strength....

Got me up and running in 2 minutes. Thank you !

Thanks for trying, and showing us your result!

take a shot everytime he says snug

Can you do this to a tea pitcher? Will heat from the tea leech the chemicals to the tea?

Thank you so much!!!

I just cleaned this same carburator. I have three inlet places . One for the gas and one for the primer. The small inlet I don't know what it was for. Maybe it was for air to the carb. I just don't know.

What do you do when you can’t see well enough to fix?

You could evevn use the right diameter of the old telescopic antena fir adjusting the carburetor 's screws. Thanks

good Job Love the song

On a murray 2500

Who sells the proper screwdriver tool?

You can't find the screw adjustment screws on my carb... I'm going in.

Thank you so very much Bob for all the insight on topics you just cannot find answers for anywhere else. I hope everything is going well for you! Take Care & God Bless!

greatest video ever thank you

Thx, got a GM so even better I found you with yours. Had a good idea it was the starter but didn't know where to find it. Now I do, thx

Thank you, I had the same exact issue with the same exact machine, what are the odds? Thank you again.

Thank you Vice Grips Bob. I'm about to use this recipe on an alumitub submerged aluminum firebox.

Can't you just take the Positive off and leave it off for an our to do the same thing?

They're trying to make it a hard as possible to do any home repairs. I'll give your suggestion a try until I get my adjustment tool in the mail. Thanks.

Thank you. Just put a new carb on the wife's weed eater and was needing to pull the plug and add a drop to start it. This should make it all better.

Why not clean the bearing with gasoline then pack them? Why do you mix the old grease which came out back into the new ? :)

My 32cc professional 4 cycle craftsman weedeater doesn't have those screws.

You saved my MUTHAH FN DAY !!!!!❤

You are, the man worked like a charm