Well at least now i know this is needed. 455 with probly couple hundred hours never greased or oiled this part. Now i know.
@AutoTuneTM9 күн бұрын
Husqvarna 545 chainsaw the shaft is hollow on the clutch side and has a small, lateral hole that leads to the bearing, so can pump a little grease into the end of the shaft and out to the bearing. Your 455 there is no has grease hole.
@JohnNyerges10 күн бұрын
This was all I needed, thanks.
@johndoe726811 күн бұрын
Thank you a video is worth a million words
@gpooleii12 күн бұрын
Great video, well done. Thanks.
@eduardocastaneda62218 күн бұрын
Thanks,very good
@jormond726620 күн бұрын
Helpful video. Thank you.
@THEMCWILLIAMS9524 күн бұрын
Short and to the point and showed me exactly what I was looking for. Thank you.
@user-ym5pv5tq4p27 күн бұрын
Never said what kind of grease thumbs down
@alexstewart224723 күн бұрын
Just Multi purpose 😊
@briankinnane52247 күн бұрын
It says Husqvarna multipurpose grease right on the tube.
@imretoth234128 күн бұрын
😂😂😂
@user-rc8sq8en2w29 күн бұрын
Echo PB-770T Backpack Blower?
@alexey.8676Ай бұрын
Is this your husqvarna multi purpose grease? I saw the same tube in another video but there was black grease inside...
@alexey.8676Ай бұрын
Is this grease molybdenum? (color black)
@fabionelsogonzalezecheverr2480Ай бұрын
How many working hours can you work with a Husqvarna oiler?
@fabionelsogonzalezecheverr2480Ай бұрын
How many working hours can you work with a Husqvarna oiler?
@petercronkright8482Ай бұрын
Very much appreciated the video after pieces sprung out while taking the handle apart. Thanks. All the triggers work except my STOP button. Could not start the engine and the STOP but now has no resistance. Could I have disassembled the STOP button during the process. No mention of it in the video.
@AutoTuneTMАй бұрын
The fault is either in the stopswitch or the short-circuit cable. Change the switch as needed and inspect the cableinsulation for damage.
@petercronkright8482Ай бұрын
thanks.
@imretoth2341Ай бұрын
😂😂👎👎🤮🤮🤮
@ScooterDogeАй бұрын
That looks easy. I’m gonna take apart an old metal coat hanger instead of buying that fuel tool. Thank you!
@thejuanmusic1Ай бұрын
Excelente ilustración. ✅✅
@k9spike235Ай бұрын
What about the on off switch assembly side?
@imretoth2341Ай бұрын
Mi van veled nem videozol?
@agmac500Ай бұрын
Perfect. No talk needed. 🙏
@jameshilton301Ай бұрын
But if there is no grease leaking out before is this necessary?
Generally after a good usage it is better to add grease. Be it any machinery where ever, you see the grease screws make an habit to add grease. This will help you with smooth performance and great quality to the engine
@jumardyelectro82432 ай бұрын
Hanya ini yang membuat saya paham saya kira bautnya yang di setel untuk mencari kemiringan ternyata ada garisnya dan baut yang dua itu adalah penahan kikirnya terimah kasih
@imretoth23412 ай бұрын
😂😂🤮🤮👎👎
@NoelInnocentBOHUI2 ай бұрын
Excellente
@yassirc36812 ай бұрын
Excellent video! No talk, all action.
@rachelkamen71812 ай бұрын
Thank you!
@slicenugget2 ай бұрын
Thanks for full length video! I'd be scrolling the insta...
@rasso012 ай бұрын
Yu
@markscarupa47132 ай бұрын
Gotta have audio
@arekguinness23422 ай бұрын
Very helpful video. Thank you 👍
@teokastelan29303 ай бұрын
Thank you for the video ! I got new Husqvarna 555 RXT. And I noticed that the gearbox is hitting too much. Fortunately I use the machine only maybe half an hour. I did add grease lubricant. The instructions are very vague. Can it be too much grease ? I had so much that gears are flooded…
@AutoTuneTM3 ай бұрын
What cutting equipment have you had fitted? Make sure it is fitted correctly.
@teokastelan29303 ай бұрын
@@AutoTuneTM Thank you for answering ! It is a regular head for weed. Is this fitted correctly. That is my third trimmer. Before Husqvarna I had MTD trimmer. It was a good and strong trimmer. But unfortunately, I can’t get parts for it… I think I bought it in 2008.
@aleksandarcosic11433 ай бұрын
Thanks you
@xgeneral25023 ай бұрын
There are no rocks on the surface so it is possible to cut without the plastic shield. It just makes work slower.
@cipriandenes66413 ай бұрын
Thank you my friend !!!!!❤
@joelek5894 ай бұрын
Many saws of multiple brands do NOT have a grease hole in center of crankshaft. That hole in center of crankshaft is for tooling center point for lathe that makes crankshaft only. Pump in grease = no grease comes out side of crankshaft to go into needle bearings. A good practice is take off clutch, drum, needle bearing to find out yes or no does your saw have the greasing feature that is shown in this video. No hole in end AND side of crankshaft = no grease feature upgrade.
@novocainesoul45293 ай бұрын
I don’t believe Husky saws do not have a grease hole. Don’t be lazy, take off the clutch and grease it correctly.
@aresmares80594 ай бұрын
How do I clean the tubes that go from the two fuel tanks to the carburettor?? To eliminate old oil and mixture?
@AutoTuneTM4 ай бұрын
What tubes are you talking about? The normal action is to buy a new hoses and replace it.
@aresmares80594 ай бұрын
@@AutoTuneTM The pipe that goes from the carburetor to the petrol tank, I used a poor amount of oil to make the 2-stroke mixture and I would like to clean the pipes from oil residues in the mixture, and I was wondering how to do it, if it is convenient with a syringe, detaching the pipe from the carburetor and pushing diesel fuel up to the tank
@mailstr29584 ай бұрын
Informative video. For me, everything is clear after watching it. Thank you very much for sharing the procedure. 🙂👍
@thefringeminorityreport47974 ай бұрын
Learn sumtin new every day
@vasidaniel5 ай бұрын
Crap. O porcarie
@jjjjjjjjjj25265 ай бұрын
What did you use to close the fuel line off?
@user-ed3og9rx8h6 ай бұрын
555
@justbaumwolle11056 ай бұрын
Im looking for a 254xp and i already have a 141 from 98 and still runs great but im gonna rebuild it soon tje 254 im getting looks like outta the shelf
@paulweber85146 ай бұрын
no audio sucks
@mikekmalick6 ай бұрын
Cat got your tongue? An easy fix! Thank You!!!
@Ralf1erudd8 ай бұрын
rev it out you tart you wont break it
@JDog1728 ай бұрын
Wear gloves. Don't touch gas.
@omegoa8 ай бұрын
Way too long for what was shown. Just say upfront that a proper size of file used in an outward filing motion and correct angle will sharpen all surfaces of the tooth, otherwise you'll mess up a portion of the cutting surface. All that other jazz about the angle of this and that surface is distracting and unnecessary. Maybe a bit more about the "depth gauges" and how/why they need to be maintained. It's only a dumb question if you already know the answer. Otherwise, very good video - nicely done.