What was the cost of the axles differential and bearings etc in this video

Camber/ heim adjustment while putting the front tires on?....where's that instruction?

What is it called ??

At 17:00 where can I find that gear? I ordered one but the shaft size was too big to fit the bearings

Thank you for sharing

Good paint job, indeed !

I also wonder why the manufacturer, have not incorporate in the design, Disk Brakes

There is corrosion in the battery wells, I wonder if sandblast would work better to remove the damage?

I enjoy your work. Whats the specs of torque, to those screws (4) to these two retrainers . And witch oil and correct amount to refill the differential. I think you corrected that noise. Thank you

hated the music

Ok

I'm trying to find me a golf cart with dump bed

Im trying to find me one a golf cart ith dump bed around $20.00

Hey brother, I just rebuilt my golf cart rear end just as you did.. everything went smoothly except when I installed it and hit the gas I heard a loud constant noise.. my question is, is there a certain way the gears half to be lined up? Do they half to be the big chunk in the back and the middle gear are close to each other but not touching.. any advice you can give me on a trick to stop the noise.. I put all new bearings but took the gears out of a used rear end that had structure damage.. the gears looked good, I inspected then well.. please help.. thanks..

Nice work gent!

Any idea on ehat size bearings i need for a 93' EZGO txt? I cant find the info online anywhere

Hi Dave, can I ask where you get all your parts from for the TXT ?

I pulled my hub and bearings a few hours ago and learned that I should have tapped the hub with a plastic/ rubber hammer instead of a small steel hammer just like the shop manual said. Even though they were light taps, the cast hub broke. Duh.

Can you install my lift kit if I help you? I'm in South Carolina myself.

I changed mine and the valve still ticking

Great job!

you forgot the center pins in the bottom of the diff. and the u bolts go from underneed

Thanks for the video! Any tips for removing that top gear and bearings? Those two bearings on the input shaft are definitely bad for me.

hello what rocker panel u used for ezgo txt

SOS pads (steel wool soap pads) clean alloy parts up really well. Everything looked like new, except the diff housing. But, now you know if there is a next time. Stuff like this is addictive, so I'll assume there will be a next time. Thanks for sharing.

Thanks. I’ll be doing mine this weekend. Video helped

How would you go about adding two or 4 wheels for a ultra smooth ride

Dave, thanks so much for making this video. I had a 'Custom Cartz' shop do some maintenance recently and it was not done properly (for starters the new axle bearings are totally shot after only 3 months...if they actually replaced them). I tried your link to the rebuild kit in your description but it no longer works. I have a 2005 EZGO TXT PDS cart with the factory Dana rear end. Couple of questions: 1.) Can you provide the link to the bearing seating tool set you used to install the bearings? 2.) Can you provide the link to the bearing puller set you used to remove the bearings from the differential? 3.) Any suggestions on removing the motor which is stuck to the input shaft (motor housing spins freely after the bolts were removed but it will not come off the input shaft? Thanks again for the great content. Cheers, Jeff (Garage Maker Guy)

Great video

So i guess no part 4? Beautiful build so far

I wish you had better lighting on the axles. Your camera was facing directly outside toward the light making the contrast very bad in the important stuff. You went to a lot of trouble to make the video. Cinematography needs work. Thanks, though.

What ever happened to the rest of the rebuild series?

This looks to be a really good series. Thank you for filming all of this.

Hi Dave, I clicked on the ebay link you bearing kit you used but it did not pull it up. Do you have the part number fort that kit by chance?

How did you fill the differential oil? Mine only seems to have a drain plug. Guess I could flip it over.

At the 21:00 minute mark you are attaching the leaf spring. I'm wondering if you could tell me the part that attaches to the frame? One of these are broken on my cart when attaching new leaf springs I came across this problem. Thank you.

David what size tire you put it with the 6/ Lyft live

Hi, could you cooperate with us? We have some products of golf cart accessories.

Well done! Mind providing your contacts? We can talk about cooperations.

Nice goonzquad shirt

Excellent video, well done mate! Unfortunately I found your video after I installed my lift kit on my club car incorrectly, I had the rear lift blocks backwards, short side was facing backwards. 😢 Wasn’t going together correctly. Missed that critical step in the paper instructions 😮. It was easier assembling second time around though 😂

Thx Mate for the tip on the longer drivers side brake cable. I had same issue with my lift kit installation.

Did you end up replacing the differential? You said the spider gear(s) had possibly too much play in it. Is that an acceptable amount of play in them? Thanks. Great video! If the diff. gears themselves are worn out, where do get them? - I can't seem to find them for sale on ebay.

Everything is on KZbin, thanks to good lads like yourself!

Did you notice if the drivers side brake cable was too short after the lift?

حلوووووووه

Not sure if I missed it, what paint did you use on the frame?

Did you have to take anything apart to get to that

Thank you for the videos. it helped me to understand what I was getting into before starting and how to prepare. Hope to see Episode 4 in the future!

I bought a set of those Sams club Duracell batteries two years ago and two have already gone bad.