THANKS, FOR THIS GREAT "UPGRADE" SUGGESTION!!

Yes it's very good however I could do with more explanation on setting up the switches. the instructions are not very good

I have the same Remote were do I buy the Batterie upgrade

I’m having problems connecting my Flysky fs I6x to my mission planner ,no bars for any channels ,any help you can provide ?

Great review . Thank You

THANKS>.............! THANK YOU FOR THIS VERY HELPFUL RECORDING. Regards.

THANK YOU, thank you for this wonderful presentation, not too fast, not too slow. REGARDS.

Is this is better than m9N or m9N is better than this for pixhawk... Pls reply soon..

Ya went way to fucking fast on those steps

Hi,do you need to change settings in the transmitter programm to use a LiPo batterie (in my SPEKTRUM i had to change settings from NiMh to LiPo)-also,if you remove the LiPo from the transmitter for charging,what happens to your programmed settings on your transmitter...i hope you don't have to re-programm each time after charging ?Last question-do you really need to discharge after each use ?

So what is the first impression?

What's the name of frame

Thanks for this video. It was so much better than trying to read the manual. 👍👍

is there any way to get last known GPS coordinates from AT10 if you crash and loose drone?

Does this work for hexacopters as well as quadcopters?

Cool I tried this on my fs i6 and completely ruined my drone and transmitter so just ordered new drone and transmitter 😃

I thought you could customise the alarm for low external voltage as read by the PRM01? How do you do that?

Could you, or would you flow chart as to how to download a video onto a microSD card with these goggles? Mega thanks. ☺

I was wondering if to buy a Lipo for this transmitter but when i come to think about having it discharged every time after flight i think im just gonna stick with rechargeable 1.5v regular batteries. I dont see any real advantages having the lipo.

What type of connector is used? Is it JST SH 1.0mm or something else?

My RSSI is beeping and won’t stop.!!! How do I stop it ???

Thank u so much this is the only video I could find on how to get the rssi signal into betaflight

Hi, does this gps module have a flash memory to configure it or to update firmware??

It have telemetry feature??.

I have the Radiolink AT10 and the functions of the analogs are reversed; the analog on the right does the throttle and vice versa. How do correct it?

Please Help settings? Linki: kzbin.info/www/bejne/rZ6qgH55jLetmMU Contant priv. [email protected]

How to purchase this transmitter

How

Helpful video thanks. My rssi stays at 25. Please help me fix this issue. Radiolinkat10, R12dsm receiver

Палишься

Still relevant today, thanks for the video!

Helpful thank you very much for sharing

Very usefull video!planning tou update!A quick question..after flashing-updating do you losing the preset models from the transmitter?if yes..is there any way to back up them.ian using full 15models..will be a big pain to reset them all up.thank you!

Thank you for the video. At 0:58, I noticed you say connect battery to channel 3 when ready for binding. Why just channel 3 and not any other channels from 1 to 11?

I bought this transmitter with receiver and I want to use it in my boat ... But when I plug the battery the motor after beeping start and dont stop . It stop only when I push into reverse .Any idea for set-up ?

I have the EWRF e7087U if somone could help me out and let me know how to switch the mw on it I would be very thankful

Hello, one question I bought that device, but it does not detect the camera signal of my KY601G drone, will it have to see something that the camera is 5g?

Why did you chose BAL-CHG instead of CHARGE?

I got one of these a few years ago, it has worked as expected, however a few days ago, I tried updating it. I used the firmware from the company website, and on their website it said that the V2 board, the version I have, is update-able on windows 10, however when I tried, it black screened, when I tried again on a windows 7, it still didn't work, and now I am stuck with a broken radio. I would recommend that you don't buy this radio, and if you already have it, don't update.

does the sound record?

Sir ,I had downloaded the firmware from here which had .rar extension and when I had used windows 10 and 7 the AT 10II is not working showing black screen,please help.

Hi. I can't connect this SE100 to my CC3D. Radiolink told me I need to solder cables... It is possible to connect this GPS without soldering? I think the flight controller on your video uses the same JST connectors like the CC3d... Thanks!

I’ve been having signal loss issues well within the claimed 400 meters. Like at 100 feet. It lost signal today, fail safe kicked in, and prevented me from turning the car. Took out a front A arm and turn buckle. Little bit pissed.

Hello. I have a little bit sideways question: Is it receiving the "normal" 5.8GHz wifi network? Let me reformulate it, English is not my native language: may I use this FPV receiver for my android tablet (which has only the 2.4GHz) to connect to 5.8Ghz wifi? Thank you in advance :)

Hi Anyone knows how to factory reset

Where the band of raceband ?

How far this transmitter can go until lose signal?

How do I change the device language and convert it to Arabic? Can it be converted to the Arabic language?

Nice review! Do you recommend this tx on 1/5 scale Baja?

Great video dude... you have no idea how much u helped me out! Much appreciated 😎