Did you add any weight, or are the split rings and hooks enough to cause the lure to go upright?
@binglebuildsit6 ай бұрын
Exactly. The lures this size the hardware is enough. If I were to build a larger popper I probably would consider adding a belly weight.
@Fishingin2906 ай бұрын
@@binglebuildsit thanks bud, love your work.
@oreadzaip21737 ай бұрын
Great video. Can you tell me those little ring scrues how are called?
@binglebuildsit6 ай бұрын
They are called eye screws. I source mine from Janns Netcraft
@jeffdemuro42089 ай бұрын
No matter how hard i try l always seem to have a few checks that need to be sealed.
@Tenchhunter10 ай бұрын
Excellent video, really like the lure, I prefer the nice natural finish to painted ones, brilliant 😊😊 tight lines from England
@reloadNshoot10 ай бұрын
Most likely a bees wax and mineral oil paste was applied for the finish
@kantana1110 ай бұрын
Awesome build
@fazanhamrock39732 жыл бұрын
I did it myself thanks to woodglut.
@joshpederson59262 жыл бұрын
Where did you get your centers for your lathe? Awesome build i make lures as well? Thanks
@madeinussr57072 жыл бұрын
Жалко что доска получилась дерьмо, переплета вообще нет.
@bethannproper24492 жыл бұрын
hi
@mass1125942 жыл бұрын
This is awesome! Thank you for showing all the steps you took to get to the end product.
@anthonyrichard4612 жыл бұрын
Beautiful!
@joannaguido63802 жыл бұрын
Hi, I am going to build a end grain 4x6 ft. island butcher block using maple and walnut. Any suggestions on lumber amount? I was thinking 10 of each 4x6.5 boards. I’m new at woodworking and have fallen in love with making cutting boards.
@SpartanORGN9 ай бұрын
I know this comment was 2 years ago, but I'm trying to figure out the math for this. So let's break it down this way. 4ft wide = 48" at 1.75" per board need 28 pieces. 6ft long = 72" at 0.75" thick per board need 96. (Assumed thickness after milling a 1" thick board) So 28x96 = 2,688 pieces Then 6ft board = 72". 72/1.5"(thickness of each piece) = 48 pieces per 6 ft board. You can get ~3 1.75" boards from ripping a 6" wide board. So 48x3= 144 pieces per 6ft long 6" wide board. 2,688 pieces / 144 pieces per 6" wide board = 18.66 boards to make this. If you wanted 1" thickness it would be 12.4 boards.
@scottcountryman60903 жыл бұрын
Your shit is dope
@uncledavesfrontier68463 жыл бұрын
Good job brother
@markr.15843 жыл бұрын
Very nice. Good job
@garrysweet81603 жыл бұрын
The cultured sprout synthetically rub because motorboat superficially flash off a obnoxious tablecloth. mysterious, nonchalant windshield
@sorinrobert40743 жыл бұрын
BRAVOOOOOOOOOOO
@conorglennon78213 жыл бұрын
Great video! What was the wax at the end?
@binglebuildsit3 жыл бұрын
Made it myself. Its a mixture of bees wax and mineral oil.
@VanessaMartinez-bf9si3 жыл бұрын
What did you put on it? How long did it have to cure?
@jillkismet1503 Жыл бұрын
Put it on various speeds to try and read the package
@ResearchDesignBuild3 жыл бұрын
Looks Great! I did a very similar project. How is yours holding up since you built it? Any cracks or warping?
@binglebuildsit3 жыл бұрын
I went over to the customers house the other day and there was surprisingly no warping/cracking. I think there will always be a bit change to the wood with the seasons but nothing thus far
@ResearchDesignBuild3 жыл бұрын
@@binglebuildsit Thanks! I'm sure it will serve them well for a very long time.
@robertkat3 жыл бұрын
All butcher blocks are made from Maple. Never from Walnut. Walnut is not hygienic.
@marcusstephens25173 жыл бұрын
Except for this one
@danieldoyle36253 жыл бұрын
Very Nice! Great job!
@TomSmith-pw7uw3 жыл бұрын
Would love to see the finished kitchen island!
@chefgiovanni3 жыл бұрын
Even easier than making it, we order USA custom made kitchen islands of Walnut / Maple @ chefdepot.net/butcherblock7.htm
@porterpacella85163 жыл бұрын
How are you planning on attaching it to your base?
@binglebuildsit3 жыл бұрын
I left that up to the customer. Not sure what he ended up doing
@afaaqusilly3 жыл бұрын
Where'd you get the wood from?
@adrianmillington92033 жыл бұрын
Great work, thanks for sharing.
@isopropylharbor89433 жыл бұрын
Subscriber 70
@Philmoon693 жыл бұрын
I have just ordered that little angle thingy from hare and forbes (different brand but same ) so thank you very much i hadnt seen that handy little tool before today!
@DsHardWoodCreations4 жыл бұрын
Very nice. Subbed to your channel
@BsScienceGeek1014 жыл бұрын
I noticed you jointed the edge grain, but not the face grain. Was there a reason for this? Were the boards already jointed on the face grain? I saw that you planed the glued sheet (~4:12), but that wouldn't take out any board twists, bows, cups, etc. Lastly, around (5:41) you run the end grain sheet through your planer. I always heard this is a no-no and it can really mess up your planer as well as your wood piece. How did you avoid these errors from happening? Thanks in advance.
@jamesdeclan75383 жыл бұрын
Its not just a no-no its a never-do and the reason why is with a straight knife, lunchbox planer with no anti-kickback pawls the blades can suddenly grip onto the vertical grain and as the rollers are only rubber, it will shoot out one end. If the person is not smart they will be standing behind the planer and get a board to the stomach and probably die. If reasonably smart they will stand perpenicular to the blades and only get shrapnel of the knifes in their body and blind them for life possibly lacerating the femoral artery and bleeding to death in 20 seconds. Even if done succesfully it will most likely leave you with deep tearout in the product.
@davesdigitalnomadlife2 жыл бұрын
@@jamesdeclan7538 That's a little bit over the top don't you think?
@z0mb0tjosh00022 жыл бұрын
Running an end grain through a planer is a 50 50 thing. I've run end grain through planer only with 2 non end grain sacrificial boards at both ends. So if the planer were to catch on to something it would be the edge or face. Take light passes as well. If you try to take a whole lot off it will definitely fuck up your planer. Also just make a router surfacing jig they're easy to make
@1873Winchester Жыл бұрын
If you have a helix head it's pretty much OK to do this nowadays, notice the sacrificial boards on both ends too, that's to prevent the tearout.
@dinohudson14324 жыл бұрын
I can't work with wood, I'm a metal guy. Obviously you're a wood guy. Thanks! Great vid. (sub)
@remzijeajdarevik41333 жыл бұрын
8
@dragonsinygo43874 жыл бұрын
I'm completely new to wood working and stumbled across your video. What were the two things you used for your finish? The stuff in the jug and that wax like substance. Sorry I'm a complete noob to this stuff but I'm interested in learning 😂
@binglebuildsit4 жыл бұрын
Mineral oil and beeswax!
@TwilightGarage4 жыл бұрын
Man I'd love to buy that entire board.
@Dylan_Miller4 жыл бұрын
Wow great job. Thanks for sharing man, looks awesome.
@binglebuildsit4 жыл бұрын
Thanks for watching!
@Dylan_Miller4 жыл бұрын
Bingle Builds How many BF is this top? Just trying to get an idea of how much something like this would cost to make
@binglebuildsit4 жыл бұрын
Dylan Miller this took a little over 40 bdft. Of course a few mishaps could of saved me a bit
@Dylan_Miller4 жыл бұрын
@@binglebuildsit Awesome, thanks for the info. I am just starting to put a few wood working tools together and I am dreaming about future projects and wondering how much they will cost roughly. Any recommendation for bar clamps and pipe clamps? I have zero at this moment and need some for my first project.
@binglebuildsit4 жыл бұрын
@@Dylan_Miller I just have slowly picked up Bessy pipe clamps as I needed them. Got mine from home depot. I would probably go with the 3/4" size.
@jsgeh764 жыл бұрын
looks great! What paste did you use for finishing after the mineral oil?
@binglebuildsit4 жыл бұрын
I appreciate it! I made it myself but its a bees wax and mineral oil mixture
@bla53534 жыл бұрын
Nice work! Planning out an island build here and stumbled across your video. I'm curious if you have any hindsight wisdom to share - any lessons learned/things you'd do differently after all said and done? Also curious of approx cost and/or how you figured amt of lumber purchased..
@binglebuildsit4 жыл бұрын
I would probably let the wood rest in my shop a couple weeks after the milling process. Then come back and glue it all together/mill boards that needed it. Had some issues with wood movement early on but got them worked out in the end. Probably wouldn't change much on the process other than that. In terms of cost, that will depend on your bdft cost of the lumber you use. I spent around $400 with rough cut 4/4 walnut. To get amount of lumber just determine the amount of board foot you need and then get an extra 15% more to stay safe. Hope this helps!