Speedy's Paint Shop

Пікірлер

@Reddy54 Ай бұрын

Use a Dremel tool to grind the two plastic rings off, cut the piece that goes across to the inboard hoses and then use a 3/4" tee and some short pieces of 3/4" hose to repair this thing quickly and cheaply. These engines are a pain to burp. It helps if you get the nose of the truck up.

@SteveG-u1q Ай бұрын

i have an 89 yj white what are we looking at $$$

@speedy94- Ай бұрын

Really all would depend on the condition of the Jeep.

@StevenShelley-b3f 3 ай бұрын

❤

@MarkTorgusen 3 ай бұрын

It's not an easy job if you have a stock truck. Any body lifted truck is easy to pull the axle housing.

@lilcrabman 4 ай бұрын

Idk if your going to see this but what kinda tools will I need to do this like special tools besides the nut on the cv axel and about how long does it take

@speedy94- 4 ай бұрын

Just basic tools, you will need snap ring pliers. It only took me about and hour and a half

@chetlucas8568 5 ай бұрын

How much did it cost to do this yourself

@speedy94- 4 ай бұрын

Truly I can’t remember what all the materials cost. If you went with lower grade materials you could probably get by for around $1000-1200.

@chetlucas8568 4 ай бұрын

@@speedy94- Im pretty handy, think it would be cheaper to do it myself or take it to a company?

@speedy94- 4 ай бұрын

@@chetlucas8568 well it all depends on you. I’d do a lil practicing before first. Also I guess it depends on what condition the vehicle is your working on. Let me know if ya have any questions?

@chetlucas8568 4 ай бұрын

@@speedy94- Really appreciate the feedback. Vehicle is a mango 95 wrangler. Decided I want to take it on myself. Could you point me in the right direction for the equipment Id need and where I could order online for paint?

@speedy94- 4 ай бұрын

@chetlucas8568 sure you can email me at [email protected]

@amazinblaze9115 6 ай бұрын

What did you mean by glaze? Clearcoat? If so what do you recommend

@speedy94- 6 ай бұрын

Glaze is a product that’s used auto body repair. Usually a two part product, one will be glaze the other is activator or hardener you mix in. Then you spread it, let it dry then sand it to a smooth finish then prime and paint. Clearcoat is another product you spray last to give a lasting shine and uv protection. Hope that helps! Thanks for watching

@benjaminsotelo6500 7 ай бұрын

What the name of the part that cost 53$

@speedy94- 7 ай бұрын

Cam position sensor

@benjaminsotelo6500 7 ай бұрын

@@speedy94- Thanks also whats the part number on that Assembly

@benjaminsotelo6500 7 ай бұрын

NVM ITs IN THE VIDEO

@speedy94- 6 ай бұрын

@benjaminsotelo6500 I’ll see if I can find it, it’s been a while since the repair

@1950sGirls 7 ай бұрын

Went through 50 belts??? Which is the right one bro????

@speedy94- 7 ай бұрын

I’ll have to check the and let ya know,lol.

@speedy94- 7 ай бұрын

If I remember correctly I put a pic of the belt part numbers in the video

@foodvlog-byrabiyaa 8 ай бұрын

New subscriber stay connected

@surfjat15 8 ай бұрын

what’s the ratio you thinned the paint at? looks really good better than brushing on

@speedy94- 8 ай бұрын

Oh man, it’s been so long lol. I usually mix stuff up to the consistency of milk, 😂. I’ll thin some down this weekend and see if can get ya a better idea!

@WSDJ225 8 ай бұрын

Just curious did you use your transmission that was matted to the 3.0 with the 3.4 or did you put something else in

@speedy94- 8 ай бұрын

We used the factory 5spd that was behind the 3.0, bolted right up!

@WSDJ225 8 ай бұрын

@@speedy94- ok thank you sir I really enjoyed the video

@speedy94- 8 ай бұрын

We’re enjoying the extra power lol, she fun to drive!

@ScottWinebarger 9 ай бұрын

I am in NC, where r u located

@speedy94- 9 ай бұрын

Close to Greensboro, you?

@ScottWinebarger 8 ай бұрын

@@speedy94- Just outside Elkin

@speedy94- 8 ай бұрын

@@ScottWinebarger nice love that mountain air!

@tonyparson4392 10 ай бұрын

What’s the average cost for you to do something like this on a jeep?

@speedy94- 10 ай бұрын

The whole job or just bedliner? All depends on the Jeeps condition.

@chandlergrogan8961 11 ай бұрын

Can you give us the proper ratio of paint to thinner when mixing for an HVLP gun?

@speedy94- 11 ай бұрын

I’ve been mixing paint for years, lol. Didn’t really have a proper ratio. If you’re using the cheap purple harbor freight gun just mix it to the consistency a tad thicker than milk. You want it to flow well, it won’t lay smooth at first but as it dries it should level out a bit. Spray it in light coats. Hopes this helps, best of luck.

@davidjessee7701 11 ай бұрын

Looks awesome! I would have pulled the roll bar off.. made it easier to spray and get more coverage behind the bars… speed liner is a great product!!! I’ve had two trucks with it

@speedy94- 11 ай бұрын

Thanks, the bolts were really sized up lol. Yes Speedliner is a great product!

@mikelovesnifer Жыл бұрын

That's a monster leaf mover lol that's great!

@markpeters8700 Жыл бұрын

Can you do the same to mine?

@speedy94- Жыл бұрын

Sure if you’re close by,and don’t mind waiting in line, lol.

@marcushaley6211 Жыл бұрын

Are you near Charlotte? My square body needs some paint

@speedy94- Жыл бұрын

I’m near the Greensboro area, at least 2 hours from ya

@YourLocalCountryBoy23 Жыл бұрын

I have buddies on my snap they are volunteer fire fighters they risk there lives for 0 pay THANKS FIREFIGHTERS,POLICE,EMS,MILITARY,ALL HEROS KEEPING US SAFE AND ALSO THANK A FARMER AND TRUCKER WHO PROVIDES AND TRANSPORTS ALL OF THE SUPPLIES AND FOOD

@speedy94- Жыл бұрын

Very true, I have hauled soy beans for a good friend of mine, Freightliner and a 40ft dump trailer

@speedy94- Жыл бұрын

Thanks for watching!

@racerx2084 Жыл бұрын

Mine just started leaking on my 1500hd. Doesn’t look to bad to do

@speedy94- Жыл бұрын

It’s not, lol. Good luck!!

@LisaBurton-x9s Жыл бұрын

U left rust under there -THAT WILL BECOME A PROBLEM. Looks great!!.

@AbelDeleon-xv9mu Жыл бұрын

Where you located

@speedy94- Жыл бұрын

Beautiful state of North Carolina

@reedcarpenter2994 Жыл бұрын

Was this a repaint or changing colors? I was thinking about changing my jeep color to white from orange. Is it better for durability to go white, if changing colors vs any other color?

@speedy94- Жыл бұрын

Slight color change, it went from white to a pearl white. The owners had a Mazda that was pearl white and really liked the color. Any color done correctly will be plenty durable. Good luck with your project!

@kilroy4123 Жыл бұрын

Exactly how I want my F body to look.

@speedy94- Жыл бұрын

Thanks!!

@Junior-rz3ox Жыл бұрын

Looks great!

@speedy94- Жыл бұрын

Thanks!! The Tamco products are awesome

@Junior-rz3ox Жыл бұрын

The start of another great paint job. Can't wait to see the final product.

@speedy94- Жыл бұрын

It’s posted fella, check it out!

@jacoley Жыл бұрын

The biggest mistake I see everyone doing when putting in a spray liner, or roll-on liner is they fell to apply etching primer to exposed metal. At some point, it will rust and rust through the liner. The etching primer is designed to stop metal corrosion and ensure correct bonding between the metal and the product. Without it, moisture will develop between the product and the metal.

@speedy94- Жыл бұрын

I’m the video I did apply a clear primer, which is recommended by the manufacturer of the bedliner. The metal was properly prepped and then primed. The Jeep has been at the beach since spraying the liner and has had no issues with bonding. Thanks for watching

@jacoley Жыл бұрын

@@speedy94- I don't disagree with you about the clear primer, which can be used over the base coat. Did the instructions mention anything about prepping exposed metal? Most big stores applications like Lowes, Home Depot, Amazon, or eBay products do not go into detail about properly protecting bare metal. If it did then the chances that people would buy their product drops. Remember these products are set up for a DIYer,. As a former body guy and owner of a body shop, you have to apply epoxy or self-etching primer on bare metal due to its anti-corrosive properties to prevent rusting. if not it will rust, it's just a matter of time. I'm not bashing the video or that you want to help others out. We would get these DIY projects in all the time and every time it was due to a lack of properly protecting the bare metal. When doing these DIY projects bed liners, you only have to remove the clear coat. The bedliner product then uses the base coat as a bonding agent to ensure that the two products adhere together. This is not hating on your video or the fact that you want to help others out. Though I would be surprised in 2 to 3 years if rust has not started bleeding through the liner, no fault to you but failure on the product's fault for not properly instructing its customer.

@servicetrucker5564 Жыл бұрын

Ain’t you got a driveshaft to disconnect

@speedy94- Жыл бұрын

Lol, only moved it 4 miles.

@servicetrucker5564 Жыл бұрын

@@speedy94- I didn’t know that. Fair enough

@speedy94- Жыл бұрын

@@servicetrucker5564 and we never got over 35mph. Thanks for watching!. She runs good but has no brakes. I’ll mess around with it this winter hopefully.

@servicetrucker5564 Жыл бұрын

@@speedy94- Love a good project

@EonJ-i2r Жыл бұрын

How long you had this suv and what type of engine

@speedy94- Жыл бұрын

My mother in law bought it in 98, I acquired it in 06. It had a 3.0 v6 but we swapped in a 3.4 v6.

@-_-John-_- Жыл бұрын

✅️

@grantp1012 Жыл бұрын

Where are you located?

@speedy94- Жыл бұрын

North Carolina

@austinhartman6541 Жыл бұрын

How did you create clearance for the 3.4 engine and the hood? Most swaps I've seen have had to cut a section of the hood for the 3.4.

@speedy94- Жыл бұрын

We used the factory 3.0 engine mounts, the intake is close but doesn’t hit. We did have to cut out a spot of the hood insulation but none of the cross braces. Thanks for watching!

@austinhartman6541 Жыл бұрын

@@speedy94- Interesting! And no body lift?

@speedy94- Жыл бұрын

@@austinhartman6541 no body lift as of yet. I’d like to do an inch lift for more air flow. But it’s just a preference of mine, lol.

@paulmcnabb8451 Жыл бұрын

The last shot of the helmet was a HUGE surprise! In addition to being a firefighter/paramedic, I am also a Medical Examiner.. I instantly recognized the helmet by the shield on the front of it; because, I was the Medical Examiner on a fatal wreck where the owner of that helmet was on KFD Truck 41, literally two nights ago! 🤯 Perfect example of a small world! Also, great job on the helmet, it looked great!

@speedy94- Жыл бұрын

Thanks,appreciate ya viewing,commenting and subscribing!!

@jackrussellville Жыл бұрын

What part of the country are you in

@speedy94- Жыл бұрын

@1heart7seas1moon Жыл бұрын

Thank you so much

@speedy94- Жыл бұрын

👍

@moinmirza134 Жыл бұрын

Whare is buffing?

@speedy94- Жыл бұрын

I forgot to film the buffing stages, sorry.

@travisscottmedina Жыл бұрын

Could you also thin this paint with mineral spirits? If so would there be any downside other than maybe more time to dry? I’m about to do the same job you did once I finish some other repairs to the helmet

@speedy94- Жыл бұрын

Not really sure, the stuff I used came fro Tractor Supply and it’s an enamel reducer. One Shot is an enamel paint. You could try a test spot, however the reducer I used was very inexpensive. Thanks for watching and good luck on your project!

@travisscottmedina Жыл бұрын

Thank you! I needed up heading to TSC and got the same stuff. I used your recommendation of “little thicker than milk” since I’ve never used enamel paint or a spray gun for that matter, and it turned out GREAT! It looks just like the one you shot and I’m a total beginner. Thanks for the tips and great tutorial

@speedy94- Жыл бұрын

@@travisscottmedina yes sir glad I could help!

@mrlaw711 Жыл бұрын

Great, great job. I didn't realize the prep work. I want my 95 YJ done inside like you did...It still looks good. Where are you located?

@speedy94- Жыл бұрын

Yeah the prep is very important, just like doing paint work all the prep is crucial. Thanks for the compliment and for watching. I’m located in good ole NC.

@haydenwright9038 Жыл бұрын

What paint and primer did you use?

@speedy94- Жыл бұрын

The primer was Transtar 2n1,and the paint was One Shot lettering enamel

@haydenwright9038 Жыл бұрын

@@speedy94- thank you!

@speedy94- Жыл бұрын

👍

@bensfixitpage341 2 жыл бұрын

Nice job. Is it possible to fit a stock 3.4 air filter box in the Gen 2?

@speedy94- 2 жыл бұрын

Pretty sure you can, the engine we bought already had the k&n filter.

@bensfixitpage341 2 жыл бұрын

@@speedy94- you've probably been asked this 100 times.. whats the mpg on highway?

@speedy94- 2 жыл бұрын

@@bensfixitpage341 On the highway with your foot out of it about 18 mpg. Would probably be a lil better without the mud tires. Just to let ya know, it’s hard to keep your foot out of it, lol. Very fun to drive!

@markjackson812 2 жыл бұрын

What ratio did you thin it down to?

@speedy94- 2 жыл бұрын

Ok so one shot is a thick paint so you need to thin ( this will sound crazy) to the consistency of a lil thicker than milk. I used the purple harbor freight gun so I wouldn’t possibly contaminate my good guns. The purple gun will do a good job, if it’s to thick and sputters just add a lil more thinner. Just to let ya know the helmet is holding up great! Let me know if have any more questions. Thanks for watching

@markjackson812 2 жыл бұрын

Did you use a full can of one shot? How much thinner did you use?

@speedy94- 2 жыл бұрын

@@markjackson812 no I only used maybe a quarter of the can. If you’re gonna prime like I did with the trans tar you can get it in black. That way you would need less paint to cover it.