I am late to the video, but I hope to receive a response. I am an architect who is interested in learning more about this software. It looks like it will provide all Manual J, Manual S, and Manual D calculations needed for the design of a complete system. Is that correct?

anyone knows how he gets 210 psi and test flow rate?

How do I get free software?

Thank you for the video. Please add a diagram at the beginning that describes the wall you will model. For example, I need help understanding the internal space 1 value of 2 inches. Does the U-factor calculator come with the Rhvac software, or is that a separate component that must be purchased?

How many sprinklers has to be considered in one zone. Eg If 150 sprinkler ( 50 Pendent+ 100upright) in 100mm pipe then how many sprinkler has to be considered for hydraulic calculation

Thanks for sharing this tutorial it helps a lot!

how did you come up with 500 for the sensible for the bedroom?

it is necessary to include all surfaces or it is possible to leave only external walls and not to include internal walls ?

Quiero comprar la licencia, con quien me contacto

Can we change the currency setup from us dollar to Indian rupee or some other countries.

I could make the video but to change the subtitle on KZbin for other languages ​​in this case in Spanish thanks

WHICH CHVAC VERSION ARE YOU USING IN THIS VIDEO ...?

I have a wall with 3 garage doors and im not sure what door material i should use for this it is aluminum door

Can you also make videos for Dpipe

After entering all the data and clicking the calculate button it's shows like pipe 1-2 cannot a 5 inches what is the solution.

Informative and Excellent...Congrats.

Helpful Software. But, can we change the Temperature value like from Fahrenheit to Celsius?

This video shows a couple of ways to import a pdf screen capture into Rhvac. Since only the last method was acceptable why wasn't that the only method to be presented? If not then under what conditions would the other methods be used? Lastly, when there are options available, a brief discussion about the trade-offs would meanifully improve the presentation.

how to increase pipe section by more than 10 in elite version 6

Why did we take 3 valves for the calculation? 3x250=750 gpm

thanks for sharing and it helps me lot

ok

Buena tarde, para descargar le programa CHVAC ¿ cómo lo puedo hacer? gracias

So clear and quite handy

for mvhr unit how need to select the parameters ?

Thank you for your useful explaining. I have question for your kind help : When inserting data for sprinklers, why we don't consider the elbows or tees that sprinklers installed in them as fittings? Example: when start inserting the first two sprinklers of the design area ( number 1&2 ) we do not insert fittings.

Excellent series overall. Many thanks!

This video should be before the reports videos as well.

I think this video should be before the previous one.

where we can get this software

I do not understand anything. I feel there are many data that is not understandable.

Video using CHVAC and DuctSize please

when I hit the new project button I dont get the same window you get nor the rhvac9 download

thanks for sharing this tutorial it helps a lot..

Please post a DuctSize video!

Do U values include the interior and exterior air film?

Very useful video

Leaving heating coil is 140? That’s leaving air temperature not water temperature right? Should be around 85F-90F

Consulta: quiero colocar demanda de bombero a 250gpm a 100psi, pero coloco factor equivalente K=25, pero el software reconoce la presión del sistema de rociadores y no los 100psi que requiere. ¿cómo soluciono eso?. Gracias.

@ 2:00 How do you handle a partition between rooms? Do I need to add the partition to "BOTH" rooms or just in one room? Example with two office spaces would have been helpful. From what I can tell, you ignore the wall; however, I have a warehouse. Warehouse can climb up to 90F (ventilation cooling only) and the office spaces need to be 75F. I can see ignoring the "partition" between the offices, but not the wall between the offices and the warehouse.

@2:15, reheat is not allowed by most energy codes. Should we be using adjust?

Favorecer de indicar ¿cómo se debe cargar los datos de la bomba seleccionada?

Why the point of the demand line, didn't start at zero, and it started at 10 psi?

Please make videos on project

Hello, can you please tell me where we can add floor number in this software. For example ghe zone is on second so where we put the floor number. Please reply soon.

masterdation

Hi, I tried to save as... but it pops out a window asking me to install autocad but I already have it installed, after that te program stop working 😰

Hope can have vidoes on Elite Fire Pro

Are you adding any more weather data for areas concentrated with R&D and biopharm facilities?

Thank you! Wants more such videos...