RXETDRYTFGYIU

I have a new Haas TL1 Lathe...The rortary handle jogging feature is flawless......... however the book says jogging can be accomplished by holdind down a directional jog button , which has never worked. Is there a setting or somthing to activate the ability to jog by pressing and holding the directional buttons ?

Thanks, just what I needed.

Does anyone know why 150lb is placed at joint C? Normally should not the weight be put in the center of gravity? Since the distances AC and CD is not equal I don't think C is the center of gravity.

Very good video, thank you for the instruction

I didn’t make the song, Benson Boone made it

Good. But?! What to do if you have more than 1 base and need g55 and much more

I don't do any cnc or any sort of machining, and I loved this video. Autistic engineer father sent me this, and I loved every second of it, haha

I tried putting in the axis but the dimensions are too small and I don't see a solar panel model in the thingverse

Great video man, I'm working on a camera mounting plate for shoulder rig. The one that came with the rig is NOT sold seperately ??? so have to make a second for another camera and this helps a lot.

This is so easy. My shop teacher did some sort of counting x amount of ticks forward till it tips off, then x - 1 back to find the axis where it bumps off. His way still doesn’t even make sense to me. Thank you. I don’t know why he has to over complicate it so much

Great video thanks!

hello i have a question, what do i do when the arc is so big that the center point of the arc is not visible on the page?

Why did you flip the force of Fab. doesn’t negative mean compression?

When trying to select the top plane through the body, simply hold down the left mouse button and it will give you different objects to select.

Hii, how to take offset for round bar in VMC?

thank you very much

Very informative video.👌 Just a little hint for anyone who watches this.... To quickly access the 'Work Offset' page you simply press the F4 button to swap between 'Tool' and 'Work' offsets . Thanks Mr Fuller for this tutorial.

thank you very much ,you explain the hand folding machine so clearly.

Send me app link

With the doors closed when touching the workpiece edges using the edge finder, can you see the finder bumping off its axis clearly and easily ? Is it possible to set the spindle speed to the safe 700 rpm and leave the doors open? Thanks.

Good tutorial for beginners but with ER collets the flange that locks them in is eccentric so you should insert the collet into the holder at an angle where the flange is hooked under the groove and rotate it to align with the holder while pushing foreword, in sot sure how to do this just wiggle around while pushing but do this without a tool in it and until it snaps or locks into place. This is especially important on the larger er collets. When using a weldon type holder that requires a flat milled on an endmill be sure to tighten the set screw into the slot or flat then back it out just enough to slide up and down, if it does not hit both ends of the notch and is not captive you did not get it into the notch created by the flat and need to adjust it until you find it then tighten it tight. I think you may have gone overboard with the gloves used to hold an endmill or any tool, yes you need to be careful but if you are that sensitive then you should never touch a part because they often have sharp burrs and are covered in sharp chips that become splinters easily. In the real world you won't make it if you need a glove to handle a tool, I have had several cuts and numerous splinters over the last 30 plus years in machine shops, one of those times I was wearing thick leather gloves, I thought they would protect my hands but trying to pull stringy chips out of a conveyor proved them to be ineffective, better to rely on common sense. My advise is use common sense, learn from your mistakes and have a good pair of sharp tweezers and regular ones for the splinters sticking out of your skin. You don't have to be tough but it helps to not be a pussy either when working in a machine shop.

why did you not do lead ins on the circles? great video by the way. thank you so much.

I don't think the different coils will not have a smooth transition doing it this way

Great job. I very grateful. Thanks

Thanks

Where can i get this machine?

Why don't you just use the shell tool intead of cutting everything manually?

Vnot helpful

Excellent explanation. ❤

Just wanted to let you know that your tutorials have saved my grade because I have no idea how to do this stuff

THANK YOU SO MUCH

delta nahi gamma spike

Great, clear instructed video! Thank you

What i do is after touching off on axis I origin the axis than shift .100 than part set and do that for both x n y so u dont have to mess with offsets

great tutorial! the problem is, when i used inches conversions, my arm came out as an oval. Don't know why, but i thought it was interesting

Cute, but they certainly don't fly very straight, do they?

This is very clearly explain working procsiss amazing👍 thank you

This man would be a great teacher

Thanks so much, another recent view, 3 years late. Excellent and especially like how you touch on application to 3d printing.

Great video, great camera work. Really helped.

Great tutorial! Completely demystified this process. Thanks!

Thanks for this great work

Merci beaucoup pour les conseils

thumbnail goes hard

🔥🔥🔥

He'll yeah thank you sir !

how do you fix the problem with the main boom not staying up?

can you teaching us use g54 for set up z with table touch please

so the x and y coordinates you set on the left side upper of material, some time set up x and y on the right side upper of material or lower left or right side of material.so can you explant how do we know to find which corner will set x,y coordinates for material ? please