Good Job Mark! To bad for your overshoot just before PIT2… Could have challenged for P4.😊

Great job Mark! I was in the split below you. Our split seemed to have a bit less drama. The incidents replay had some poor driving. 🤣

congrates on p5 :-) great drive

Unlucky start, but a very good comeback indeed. Just a shame that the incident robbed you of what would have probably been a great fight between you and Sebastian 👍🏻

Nice job mate - I despaired for you at the start but I should have had faith!

So unlucky Mark. It was an unbelievable drive thou and very enjoyable to watch.

My break cable came away from the connector. I thought it was a RJ-11 but that doesn't seem to fit. Does anyone why what type of connector goes from the brake to the control box?

are you still loving the Simjack pedals?

gg

Hi, You use 6x90mm and 6x140mm screws or 8x90mm and 8x140mm screws on that build? Now I also build this rig for myself, but I don't know which screw to use.

Good result Mark. You were there ready to pounce when you needed to be. Looking at the replay at the end though, you cam pretty close to contact as the car was rejoining from the right

I just stumbled on this video, and what a great video it is. I am looking at the simmsons pro pedal set, which is basically the same as simjack. The only thing that was holding me back was that i wasnt sure they would work on some of the sims you showcase in this video. And now i found the answer..you sir are a legend..thank you very much 👍👍👍

Nice vid great driver behind u 😅

theres your sub 👋

I would say wider entry to most of your turns would be a good tip. Allows for better runs out of the turn. You might be struggling with smoother braking into the turn.

What is the best way to calibrate them

Some close racing there!👌

Wow. Race of the month from my pov. Insane start. Amazing battling. Hugely intense final lap. Great stuff. Would highly recommend. ⭐⭐⭐⭐⭐

Great racing there, could have easily been a worse outcome on many occasions, but at the same time very frustrating. It's a shame it was taken out of your hands and decided my the group of cars in front of you. I thought you'd done enough when Roland wend wide at the bottom of the Esses and you built the gap, but Nicolas was just to quick and the traffic wasn't kind to you.

Well that escalated quickly. Hopefully the iRating fund didn't take too much of a battering in this one Mark

hy i send you a message at discord!!!

Hello, it's me again. I have already mentioned before that I made the same cockpit that you have with your plans, but I have only one problem and that is how to adjust the seat (in my case Ford Focus seat) to the wood. The rails are quite short and I don't know how to remove them to screw them to the wood, so I only screwed the back part and when braking too hard sometimes the seat rises. I don't know if I could leave you my email and you can send me some ideas or photos. Thank you very much for your help, your material is invaluable.

Well that certainly started getting spicy at the end there 🤣 Very smart move letting the other car past to drag you back up to the pack, just a shame you couldn't make anything stick. I don't know how John managed to keep his head in that one, that blinking was crazy

I took 8 places.. Make sense now

Nice one, I’ve just done this and now the bar with the spacers just doesn’t fit back in anymore, only to find out I didn’t even need to take this apart cheers 👍 (Had to sand the black spacers down)

Awesome Mark :)

The last clip had me in stitches, the bonnet flying up 😂😂

Good racing Mark. Looked like you struggled a bit after losing the back of P1, don't know if you cooked the tyres a little, but it was a fun battle keeping Max at bay 👍🏻

Eventful week then 🤣

👀

You certainly made that harder work that need Mark :D I think what saved you at the end there was Matthew got a little bit of a slide on coming out of the uphill section, which then compromised his exit speed slightly. Good racing tho mate 👍🏻

gg

Hi, did you predrill holes or just screw them in? I am affraid of cracking of wood, thx

So unfortunate with the slow down mate, 56 degree track certainty didnt help. Youre qualfying a lot higher this season! That big result is coming. But damn the top 5 group are quick. Think my aim is 6th every race now 😅

should've lifted more after slow down was given could've slotted back in the slip i am daytona master

All the damage is repairable

Thats was a great video Mark, loved the gr overtake in the final turn! You are a very fair driver and deserve a huge amount of credit for that. Looking forward to watching more of your videos.

For the pedals, do you need the pedal plate? or could you just use some screws and put it straight into the wood? I ordered the pedals already, just wondering if you could do that

Call it Old Sparky!

my brake pedal is only about 10% help me🥲🥲🥲🥲

You are always so helpful, Mark.

GG dude, that was very intense.

What spotter are u using? It tell you there ir

.

I've had the wood to build mine since last fall and just haven't had the time (or nice enough weather on my day off) to get everything cut & built, same basic design in my head as yours but I plan on doing the monitor mount like the channel CKW did in a video 6 years ago "Triple Monitor Mount For Sim Rig". I'm planning on adding a sliding keyboard/mouse tray under the wheel like a traditional pc desk has.

New version now uploaded kzbin.info/www/bejne/sKHPoaekhtennKM

Been trying the ray ford 1600 really nice car I keep trying PCC but keep getting wrecked lol think I will try the mustang at least the GRs will be out the way lol take it easy mate

It’s a real shame Lincoln has no consistency he’s got great pace but I find most of his decision making is very poor if he just settled down a bit he would defo get some great results your looking strong out there mate loving your driving style mate great vid as always brother

No sound for 1st 10 mins. My bad.

Got some air!!! Bummer for the guy in front. He had a massive save before getting hit.