Just wondering why you guys include the drill alignment tool on some of your nerf bar/rock slider kits but not all .It should be stranded since we have to drill holes on all of your kits . I was kind of bummed after watching countless install videos of individuals installing your products that came with the alignment tool and mine didn’t . I just received the exact same rock sliders as this video for my 900s . Again make them included on all your rock slider kits it takes the guess work out of it and makes our lives easier by not screwing up when drilling the new holes in the frame

will this still work with a winch ? thank you

Pretty cool guys, you did a great job 👍🏻

how to with no end results? I really wanted to see what it looked like done.

Great value on this install video. Thank you!

Will this fit if I have the ultimate speakers on the back?

You guys didn't even show how it works.

Is this windshield available for a 2017 Artic Cat Prowler?

This looks nothing like what was sent to me. Completely different top

By far the worst directions to replace a carrier bearing. this guy wants to take apart everything. surprised he didn't remove the head lights and wheels, all plastics and both doors. this was way over kill. do your self a favor and find another video. DONT DO WHAT THIS GUY DID> clearly he's an OCD boy-scout. uses the entire book time to do the simplest of jobs.

Id love to get one of these jacks for my sxs

Is it gas powered or electric powered?

It looks like where the windshield comes together with the lower section would be right in your field of vision.Doesn't that get annoying?

So I bought the bottom radius bars and I’m trying to put them on in my garage. And I put the jack under the right arm next to where the tire goes. So I just noticed when putting on the bottom rod, you moved the whole arm so you could line up the rod with the pilot hole on the arm. So I guess I have to put the damn tire back on so I can lower my jack, so I can move my jack off the arm, jack it back up with some boards in the middle of the chassis, so I move the arm a little bit so I can line up the damn holes😢

Great video. Very clear instructions on how to do the job, sped up for the basic work with written explanation of the work being done with good video of the entire process. Excellent explanation of camber and reason for adjusting. well done and helpful video, thank you!

This is all fine and dandy until you have a 2013 that you have added the power steering kit which now it doesn't fit

I’ve seen 2 videos saying super Atv goes towards the rear.

Very good video! Very detailed and easy to follow!

The weather stripping for the bottom windshield isn’t the correct stripping. The bulb shouldn’t be on the stripping.

I just use it , Works like a marvel

What happens if it’s completely loose? My can am Outlander is loose but I’m getting it replaced

Where did you get the lyft

What mod did you make to your air cleaner

Where can I buy one that already comes with pre install tunes for 2024 Honda pioneer 700-4

Is there an updated install video? The kit I just ordered doesn't have the small wires to make use of the pass through for the rocker switch

This is the most clear instructions I've found, this windshield on eBay comes with photocopied instructions and the pictures are very dark. At 2:29, the stock rollbar nuts should've been installed with the new bolts, that's why the spacers sunk back into the rollbar. Ok, this video helped me get the lower installed, now I can assemble the hardware on the top, since everything is unassembled on the ebay copies. And the pictures are black, I'm sure I'll be back to check something. 😅

If my drive shaft is so loose that it clanks when I put it in gear and give it some throttle, is it most certainly the carrier bearing or could it still be something else?

How would I set a base adjustment for a arms that are longer then factory?

Why did you loosen the secondary clutch bolt twice? And if it’s reverse thread why were you holding it in the position of normal thread?

Shouldn’t the fixed ears on the shaft be facing the same front and back?

Awesome. Love it. Thanks!

I literally just finished this install. I removed my wheels (less weight on the arms) and the 4 bolts for the upper and lower. No need to remove trailing arms or brake line holders.

When installing front facing turn signals be wary there is a bracket on the facing where they are putting the turn signals. They dont bother to mention.

Running the shocks upside down? Will that damage the shock?

What sizer spacers and self tap screws did you use?

Y’all are lame as f*** for cutting away at the install. Just trying to sell a $1200 part. Complete jackasses.

Are you sure they will fit? I’m 1/4” off on getting the lower ones on

SATV drinking game. Take a shot (of beer, or you'll die) every time they say "go ahead" 🍺😆

Your intro BLOWS

Video showed nothing informative to get anything aligned up... nothing on how you want anything seated for proper alignment...it showed nothing on how easy or fiddly it is to take off when it gets warm out. I was interested but after watching that it's a hard no

Will this fit a 2024 Polaris general xp1000 ultimate?? If so please send me the link

What he didn’t show in the video is lifting the windshield up and tightening the brackets. They are not strong enough to hold up the 125LBS windshield. Also leaving it down like he did you cannot get off the Uforce hood.

Need to make a video where the windshield is covered in thick mud. Scratched the fuck out of mine

I spent $580 on a polycarbonate windshield for my x3, went mudding an got scratched to absolute shit. Buying glass from now on

Can you leave the rear windshield on while trailering the UTV?

You did wayyyyy more work than you needed to do your drive belt. You don't have to pull out the clutch to do it!

Why take the seat out for that lol

I like mine.. Thank you:)

How do you remove the skid plate

I have these mirrors on my 2017, Just buying a 2024, where are these?? Cannot find them on SuperATV website.. please help