Why not use Silicone Seal and fill the cavity of those rollers and then clamp them to the bars for a few days till the Silicone Seal fully dries. Of course both surfaces need to be clean and oil-free.
@rb25303 күн бұрын
So, you invented a vehicle dolly, a 2' tall dolly, with support arms that are not capable of countering lateral loads.
@baldeaglegarage2 күн бұрын
That's not at all what is shown here. Rollers are to maneuver the Quickjack into place. Once Quickjack starts to raise, the rollers come off the ground. Watch the video again, I hope this helps
@raylopez91534 күн бұрын
Good video man I'm almost positive that's what I need my boat it's a 5.0 omc. Four winns n it it's bone dry on top like your was pretty sure pump is bad .
@baldeaglegarage2 күн бұрын
Good luck!
@ricardomanriquez16474 күн бұрын
This will fit on a Yukon Denali ? 04
@baldeaglegarage4 күн бұрын
Sure will!
@maplemanz6 күн бұрын
Some us can afford to participate.
@baldeaglegarage2 күн бұрын
I'm not sure what that means, but thanks for watching and commenting
@jimjohandes7 күн бұрын
Very helpful. Jim in California
@baldeaglegarage2 күн бұрын
Awesome!
@Finnnielsen212211 күн бұрын
My dad had one of these when i was a kid
@ironmantooltime15 күн бұрын
Stunning!
@baldeaglegarage2 күн бұрын
It really is!
@Guido_Sarducci00721 күн бұрын
Perfect side view of operation! I bought these 1" rollers at Harbor Freight, and I will use hex head self- tappers when located. Thank you!
@danpatton40803 күн бұрын
How did they work? Do you think putting a hole in the QJack would weaken it? I don't see how it would. Just asking for other ways to attach the rollers other that a zip tie which didn't work well for me. Thanks!
😊Iloveoldcarsshoe Iloveoldcarsshoe Ilob Iloveol Ilovr Iloveoldva Iloveoldcarshoe Iloveoldcarshowlovebill ye Iloveoldcarshowlovebill ye Iloveoldcarshowlovebill y Iloveoldcarshowlovebill watt ❤❤❤.😂😢😢😮😅😊
@williamwatt115321 күн бұрын
Iloveoldcarsshowsilovecarsshoo Ilobve Iloveoldcarsshowlovv Iloveoldcarshowlovebill y W Iloveoldcarshowlovebill Wyatt.❤😂🎉😮😅😊🤠🤗😸☕☕🐶😻🤟🥰🤩🤓🇺🇸🍀☘️😹😇
@DG-ie5ip23 күн бұрын
You prefer RTV over a gasket ? My 98 T/A is leaking on the floor over the winter a small amount of fluid like a quarter size circle. There is fluid on the housing and front of housing near pinion gear. Not sure what side is leaking ?
@332ARA26 күн бұрын
I just bought a truck. What does this do?
@baldeaglegarage2 күн бұрын
It adjusts shift points to help with towing. It also helps protect the transmission when towing.
@tommylang4k26 күн бұрын
Enjoyed ❤ Thanks for sharing! We ❤️ Back to the 50s Car Show in Heber City Utah too
@paulfisco169728 күн бұрын
Wow thats my old car i built it when i was 16 and sold it when i was 25. wow 100 percent everything about the doors the trunk the bumpers along with all the trim that got painted, glad it looks good still . Hopefully, the rust held out on the bottom of the back of the quarters
@baldeaglegarage28 күн бұрын
it will probably be at the show this again this year. Stop by and check it out
@giannipaul671927 күн бұрын
What he's trying to say is that he own that car before and he surprised it's in good condition and yes I'm his son
@giannipaul671927 күн бұрын
He really can't go check it out because it's all the way in Wisconsin we're all the way in Long Island and my dad scared of planes
@giannipaul671927 күн бұрын
Do you know who the real owner is
@giannipaul671915 күн бұрын
@@baldeaglegarage can you give me your email I'll give you some photos when he did have it
@WayneStephens-w9x28 күн бұрын
It's great to see a video that is actually straight to the task at hand and not a bunch of B.S. Thanks man, keep up the great work.
@baldeaglegarage28 күн бұрын
That's exactly what I'm going for, thanks for the comment!
@swamprat69erАй бұрын
Thanks for the tour and upload.
@baldeaglegarageАй бұрын
more on the way!
@johndemeen5575Ай бұрын
Back when things were Great. Million thanks for sharing this. St.Paul,Minnesota.
@baldeaglegarageАй бұрын
yeah this show is great, glad you enjoyed it
@danpatton4080Ай бұрын
Could you just use self tapping screws to secure the rollers to the frame?? I'm in the process of adding the rollers right now and hope to get an answer soon. Thanks! Dan
@baldeaglegarageАй бұрын
Why would you want to create a hole in your Quickjack frame?
@danpatton40803 күн бұрын
@@baldeaglegarage Didn't say I wanted to, just asking asking if you could use self tappers. What would it hurt? It would only be a 1/8 or 3/16th screw.
@cptoblivious7357Ай бұрын
I use mine to haul my garbage bins to the end of the gravel road that leads to my house. This one holds exactly two garbage bins and I make sure to bungee cord them to the sides of the cart. So easy.
@baldeaglegarageАй бұрын
Great idea!
@oyesukenАй бұрын
What car did the seats come out of originally?
@MrJoecool13Ай бұрын
I want to get one for my 03 chevy suburban 5.3
@baldeaglegarageАй бұрын
Its been worth it.
@MrJoecool13Ай бұрын
We're did u buy that at
@baldeaglegarageАй бұрын
Right here amzn.to/3vJ17cv
@ballinboii1814Ай бұрын
He's in Anoka a lot
@uwuana-ni6kuАй бұрын
Tarjeta de banco hastec
@uwuana-ni6kuАй бұрын
Talento. Envase, niño. O
@uwuana-ni6kuАй бұрын
Vaselina es. Mi favorito🙋👻☠️👻💁
@uwuana-ni6kuАй бұрын
Captura. De tarjetas Bisivles 😂❣️❣️👁️❣️❣️❣️❣️❣️ 🫀❣️❣️ 🤓❣️❣️
@uwuana-ni6kuАй бұрын
Tarjeta de. Descuento .
@uwuana-ni6kuАй бұрын
Adrenalina. [™✓π]. Descanso mutuo
@Thomg49Ай бұрын
You do need to remove the air bag...I used some 10lb test fishing line,,,ran it in the back of the wire clip...left lots of slack in the line...place the knob in the hole and push real easy...while pulling both end of the fishing ling..It will pull the connection clip into place...just listen for the snap....
@thebacdoc6464Ай бұрын
What a cool vidéo. If that Yellowstone 79 Formula was a W72 400 4spd, that would
@thebacdoc6464Ай бұрын
Love those 81Nascar TTAs, with thé red recardo seats. I also love thé 78 Y88 W72, fully loaded automatic, because in 79, that 220hp t/a 6.6, could only be had with a 4 SPD. I also like thé 77 200hp Blk W72 TAs. I also like thé 89 TTA 20th anniversaire
@DavidSkater7096Ай бұрын
Excellent video. Exactly what I needed
@baldeaglegarageАй бұрын
Awesome, glad to help!
@ronniepatterson28272 ай бұрын
I once owned a 1980 Turbo TA pace car like this one at 6:35, but gotta admit the custom red & black 1981 pace car right next to it, is the best looking TA ive ever seen my entire life. Amazing!
@baldeaglegarageАй бұрын
Yeah looks real good in red!
@landrecce2 ай бұрын
Sad there are no third gens
@baldeaglegarage2 ай бұрын
There are in other videos, just not in this particular bunch. Check out my other videos. There is one that is only 3rd gens.
@mercpindi55222 ай бұрын
Plug size please
@baldeaglegarage2 ай бұрын
haha, its a 3/8 drive ratchet. Its a square fastener, you don't need any socket, just the ratchet. Watch it again
@mercpindi55222 ай бұрын
@@baldeaglegarage thanks
@mercpindi55222 ай бұрын
@@baldeaglegarage job done
@eurocarpleurocarpl20572 ай бұрын
Did you change the gadket seal? Do you have to change the drain plug? And how do you know when is the cortect oil level?
@baldeaglegarage2 ай бұрын
yes, that was that sealer I showed, no you don't have to change drain plug, at the end I show when it comes out the fill port, its full. Yo can watch it again incase you missed something
@345cowan42 ай бұрын
Nice video. Hope 2024 is just as good or better. B&B Motorsports.
@baldeaglegarage2 ай бұрын
Thanks!
@saulalanis65782 ай бұрын
So i got that going for me which is nice!🤩 classics thanks for video cleancut no bolognese.👍🏽
@baldeaglegarage2 ай бұрын
Glad you enjoyed it!
@sevenpaulperalta9292 ай бұрын
There are a few videos depicting this mod. I surprised QuickJack hasn't made this available for their customers.
@baldeaglegarage2 ай бұрын
yeah pick which one works best for you!
@tompeters54142 ай бұрын
Looks kind of like La Vangs Nova
@baldeaglegarage2 ай бұрын
maybe?
@garnetshaw2 ай бұрын
Thanks im about to put a camper on. Could save a trans
@garnetshaw2 ай бұрын
I should read my comments before i post
@baldeaglegarage2 ай бұрын
haha, glad it helped!
@markdupre48542 ай бұрын
Love the Video and idea for the quick jack I have always struggled with fine adjustments for positioning!
@baldeaglegarage2 ай бұрын
Glad you enjoyed it!
@dntlss2 ай бұрын
Great video man,the guy that invented ratchet wrenches is siting under a palm tree with a umbrella drink in his hand,much deserved, its good to tell some viewers that while its ok to remove the 10 mil bolt that holds the computer to the main harness with a power tool DONT use it to put it back in,use a ratchet and go real slow till it stops and then dont go no further.
@baldeaglegarage2 ай бұрын
Yeah for sure!
@michaelgeorgianni81322 ай бұрын
I have one of those. Nice ride. #caddyzaddy
@baldeaglegarage2 ай бұрын
Very cool!
@turtlewax23 ай бұрын
Can you make me a hitch that can be connected to my bicycle?
@9011combo3 ай бұрын
Good job
@baldeaglegarage3 ай бұрын
Thanks!
@AchikSarih3 ай бұрын
Merci beaucoup ❤❤❤❤❤❤
@baldeaglegarage3 ай бұрын
Glad it helped!
@thomashingerjr88433 ай бұрын
I found seat covers and cushion on eBay for around $32 a piece! This is a great video and looking forward to having a better seat in the near future! Thank you!!!
@baldeaglegarage3 ай бұрын
Thats a good deal for something new and matching fabric! Nice find!
@brian2423 ай бұрын
Love Back to the 50s.. in my Home State
@baldeaglegarage3 ай бұрын
Its a great show!
@branthandford22123 ай бұрын
That is a rare car right there.
@baldeaglegarage3 ай бұрын
Sure is, too bad it was left out on grass uncovered for 20 years.