Thanks! Accessory install vids coming soon!

I just picked up a BC Adrenaline 600R myself. Let me know how the Woody's work out for you!

Coming soon my friend! Filming accessory installation this week!

Can’t wait to see what you think! I’ve had a similar journey as you - went from a bc sport (actually was convinced from your review of the 600EFI) to a 600 ETEC backcountry adrenaline. Still have the old one as a family sled! They’re incredible machines and the 600EFI has been phenomenal.

Yeah, MOP convinced me to give the 600EFI a try and I've been loving it in my tundra since! Just hoping for a better snow year for Ontario this year!

Instructions indicate to keep the filler neck on the right side when affixed to the LinQ mounts. I don’t know why that is, but I’ve never tried installing it ‘backwards’!

Nope, started great. The only time the 600 EFI didn't start was a -40°C day and it flooded itself. Solution was to hold the throttle pinned and crank it over. Started within 10 seconds.

More videos coming! Expedition was replaced with a Backcountry for this season. Stay tuned!

That's great to hear - this is why I make these videos! More accessory installation videos coming on the new G5 Backcountry.

Thanks! I wanted to create a reference for the 600 EFI community to properly maintain their machines on their own - seems to be helping!

The ACE engines are super smooth, but I went with a 600R for this season!

To be honest, the blue jacket was a plain winter jacket from Costco and the pants are downhill ski pants I got on discount at Sportchek! I like wearing this because it fits tight, but it's only good down to about -20°C. If it's colder than that, I wear my Ski-Doo Vasa floating suit.

Спасибо. TOBE хорошие костюмы ?

No problem! More to come.

Agreed, and that 20" wide track would really increase the [already large] footprint. I think mine has the 16" wide track (that's all they offered on the 600 EFI)

Makes sense: having it up will improve steering due to shorter track contact. Towing will be easier down because more traction. And breaking trail requires occasional reversing, which is easier if the track can lift to climb on top of the snow. Good advice.

Same here, they told me to let it float around most of the time. But locked for towing and when you want to plow through loose powder and dont expect to reverse.

I have a friend who loves the ACE engines, but he also loved my Expedition, so he bought himself the Expedition Sport 600 ACE last winter. We'll do a 600 EFI vs 600 ACE drag race this winter!

bienvenue!

Great to hear my videos are helping like-minded enthusiasts! Which Sea-Doo do you ride? I’m thinking about getting one.

I can't seem to find that in my user manual. Mine says to pull the adjuster with the engine running to 'fog' the engine with oil before storing it for the summer. What page of the owner's manual calls for the oil adjustment?

@@mop1471 They list it as an item in the maintenance schedule table. I would have to look at my manual to see which page but it might be different than yours anyway. You should have that same table though.

I only go through 1 or 2 jugs a season, so I choose to use the Ski-Doo XPS oil recommended by my dealer. My son uses 2-stroke oil from Canadian Tire and it seems to work fine too, but it’s only a few bucks cheaper than XPS oil.

@@mop1471 thanks,, same, i never used anything else other then xps full synthetic too,,, just wondering in case i have to use other oil

happy to help!

Since the 2021 recall, it really hasn't been a problem for me. Ice scratchers really helped a lot during that first season. I do occasionally get warnings if I'm filming, but that's because I'm stopped, idling a lot and driving very, very slowly (10kph.)

@@mop1471 I’m just figuring them out after looking into them I’m gonna get myself scratchers and wetter water whatever that is to me it feels like more work keeping an eye on the temp having to dip into snow here I was trying to be careful going slow staying on packed trail but here I was harming my sled and they don’t idle anymore I used to keep em running while hauling wood after dark now I’m in the dark in the bush I live where I couldnt take it in for recall I’m stuck with it here when people break there stuff that’s just it even my aunts and work ski doos brand new broken I’m glad I’m getting some money out of mine atleast I’ve seen people saying they had problems of the bat but had warranty people don’t know about them I’m feeling mine out the gas has to be close to full all the time to helps cool and I think water gets in there since they have to dip in snow when I open my gas cap it just pops up so it’s sucking

Thanks! Only problem this year was lack of snow. Trails around me (Northern Ontario) didn't even open this year. Trailered to Quebec for a week, but wasn't able to make content on that trip.

We had an interesting snow year down here as well. My 2021 expedition 600 efi sprung an exhaust leak on our trip into the cabin last weekend. What’s your miles or kilometer count on yours so far? Just wondering how your maintenance has been / any more repairs then the ski etc? Thank you and if you ever make it down to Yellowstone National park or the Tetons be sure to look me up!

I wanted to document the by-the-book storage procedure. Popping off the front bodywork is no bit deal, takes about 5 mins with a bit of practice.

It has ice scratchers, and they work well: kzbin.info/www/bejne/bYHOgYObepqrrKs

The heat exchanger extends pretty far back, but not right to the edge. Since the 2021 recall, overheating really hasn't been a problem at all. It'll happen if I'm moving at low speeds and stopping alot (which I sometimes do because I'm filming these videos!) Never overheats during regular riding.

I've never tried! I'll look into it in my area.

@@mop1471 thanks! I have this same machine, and your videos have been hugely helpful to me. Please make more!

The boat is super-fast and very low maintenance. Low draft as well. But challenging in rough waters.

@@mop1471 Thank you for your reply : I would imagine in rough waters - It is not my intention on getting into big swells but I have seen this little 150 speedster like this kzbin.info/www/bejne/oIbSk5hjn82eeqs

It floats on top. Very weird when you stop off the running board and fall so deep in the powder you have a hard time climbing back on to the sled, which is still up at the surface!

This one’s a 2021, and it was an all new engine for that year, so I don’t have knowledge of the 2020 models.

- The Orange wire is connected towards the rear of the vehicle (pin 8 on the switch if labelled, rearmost pin otherwise.) - The Red wire is connected in the centre (pin 6 on the switch if labelled, middle of the 3 pins otherwise.) - The Orange/Violet wire is connected towards the front of the vehicle (pin 5 on the switch if labelled, frontmost pin otherwise.) I hope this helps!

Thanks for the note! More vids on the way for sure! I’m afraid it might be awhile because there’s almost no snow at all in Sudbury, and we have rain forecast for this week!

@@mop1471 same story in Kenora area. I'm dreaming of a brown Christmas :(

The Expedition is a bit narrower than trail sleds, which helps a bit. But mostly, you need to start the process by steering away from the direction of the lean, find the balance point, and hold it there. Once the sled is up on one ski, it’s just like riding a bike!

This service is for RF DESS keys only. I don’t think Ski-Doo was using the RF system in 2007. Take a look at your key: if it has metal contacts inside, then it’s not RF.

That is correct, a single 1/4” spacer didn’t raise the mount enough for the gas can to clear the ridge on the lid of the cargo box, so I made a second set of 1/4” spacers for a total of 1/2”. Of course, now that I know this, I could re-make the spacer out of 1/2” material, but too lazy ;)

sorry for that, YT muted that section due to music copyright or something. But thanks for letting me know!

works on RF DESS keys. I’m not sure, but I think a 1998 key would have had the metal contacts inside, so the RF Dooplicator service would not copy the 1998 key.

That 2-pin connector is the rear passenger heated grips wiring harness. The Expedition Sport includes the harness from the factory, but does not include the rear heated grips. Since the harness was factory installed, rear heated grip installation was made easier than it otherwise would have been!

I hope you love it! A close friend ordered one with the 600ACE for this season, so hoping to make some good comparison videos between the two engines in the same model of sled.

I've never had ski-skins on this Expedition, but I've tired them on a Tundra. Different experience: the skins won't sink at all because they're super-wide. The DS2 will sink, which can be helpful in some situations. If you intend to tip your sled on its side to get through difficult terrain, DS2 is better. If you're going to keep your sled upright, with both skis on the ground, ski-skins all day.

Yeah, sorry about that, the background music caused a problem with youtube, and my options were to remove the video, or just mute the portion with the song. Not ideal.

I've really been enjoying the 600EFI, and it's a great value for a 2-up sled. While you're doing the rear heated grips, you might as well get the rear heated visor connector too. Otherwise, you'll have to take the whole handle apart again to do the visor plug later.

@mop1471 Thanks for the advice, just have to find one now , a place near gravenhurst says they'll be getting some in , and put one aside for us

The dealer here in Sudbury keeps a good stock of the heated grips, and I would imagine most dealers do. Good luck with the install: it is a bit of work. Take your time and double (or triple) check everything before cutting the plastics (I nearly cut the switch opening in the wrong side!!!)

DESS is inevitably far more complex. I rather like that my 600EFI has a plain old key ignition.

If your '15 Summit has the RF DESS key, then yes, it will work. You can identify the RF DESS by the plastic 'ball' you snap your key onto. If it's all plastic, they you have RF DESS. If it has a metal ring and a metal contact on the top, then it's the original DESS (not RF DESS.)

Oh my! The good news is that your 600 EFI has a 'classic' ignition switch, meaning there is no expensive 'chip in the key' or anything expensive like that. A new ignition switch would have to include a key - how else would you operate it! First step is to try to dislodge whatever is jamming the ignition. I would try using a strong magnet, which may extract metallic objects stuck in the ignition. If that doesn't work, very fine screwdrivers or picks may be inserted to try to clear the obstruction. If you can't dislodge whatever is in there, then replace the ignition switch. It's just an old-fashioned key switch. My '21 Expedition's ignition switch is part number 515177063 and costs $59 up here in Canada. You'll have to remove the upper bodywork to gain access under the dash panel - this may take you a bit of time if you've never done it before, but it's really not that bad (see my video linked below.) Once you remove the body work, there will be a connector on the back of the switch to remove, and a nut holding the switch in place. Remove those, put your new switch into the dash, replace the nut and connector, then reinstall your bodywork and you should be as good as new. Removing the upper bodywork: kzbin.info/www/bejne/p6S1cmBuadymi5I Let us know how it works out!

Good question. I'll look into it. I'd like a recoil starter as a backup, so if it's offered, I'll make an install vid!

Just checked with my dealer: Yes! They offer a pull start kit for 600 EFI! It’s $260 up here in Canada. Might pick one up - my 600 EFI has never let me down, but I’d like a pull start, just in case.

@@mop1471 nice, looking forward to the install video, have a ace, dont like the fact that I can not pull start when needed. Might have to go with a 600 efi if it works out.

Fuel and Oil consumption documented right here my friend! kzbin.info/www/bejne/pZKlZGmIf91potE Extreme cold: if it doesn't start right away, hold the throttle open and try again to avoid flooding the engine. It hasn't let me down yet. Coldest day so far was about -36°C.

Let me know how it works out. I'm planning to do a series of suspension adjustment videos next winter, and your feedback would be helpful!