Must be different on the 03, I don't have that under my cowel

If you did it with one hand holding the camera, it's gotta be simple

Anyone used the after market crank sensors? And could not doing the real arm cause a lean condition. Bank one is lean and one of the codes says crank sensor not relearned I bought it this way not sure if the sensor was ever changed I may need to change it someone help.

Thank you

In my 99 model the rear deck and seat belt bracket assembly blocks a wrench. You have to remove it. What a pain in the ass

is it located in the same postion on a 2015 cadillac escalade esv?

My retainer is not the same. This is such a pain in the ass

What was the piece of wood for?

Do you have the new assembly part number?

Doing this next thanks. Chased everything else, why not?

Can anybody help me with suggestions I know it could possibly be more then one issue but my headlight low beam doesn’t work. My dtr and side markers work but not the low beam. I’m thinking it’s the harness wire or connector because I changed the bulb and ballast still doesn’t turn on.

Had a hard time getting to the hoses without removing the wiper bar on the drivers side and very difficult to get to the one on the passenger side. So I used air compressor to blow into the hoses on both side and then from the top of the tray until I could feel the air coming through. It worked. Thanks for the video.

Good video

Did l miss installing new bearing races?

Awesome man... I have been through this whole car...(Lexus ES300 2000 model)... I never thought about looking for the fuel filter, until I start having gas flow) problems... I didn't even want to go to the trouble of looking to try to find it, and this was the first video I went to, and you took me directly to it!! Awesome man thanks!!! Merry Christmas to you

Would you have an idea bought a 2002 but when I step on the gas I only going 30miles how can I repair this where do I start ?new motor. done a tune up any idea thanks

That was really smart of you thanks for the help it work great

Wow pretty cool man

Hello, i installed the Old man std lift kit on my LX 470, 2002 model, i am hearing a clicking sound on the fron wheels as if its the CV. By change you had this issue and if so how did you resolve it?

That wrench wasn’t even long enough to touch both posts at once - drama queens

Thank you for sharing this! Very helpful, just joined into the industry and im very super green so far i love it. Greetings from California

Thank you so much for making this video. It helps me a lot.

Thank you for the help with the back seat part .

What do I do if I don't have a grinder or a chisel or money for said tools .-.

Heres an easier tip. Make sure your sunroof is sealed when shut or completely shut when raining.

You were dangerously close to shorting that battery with the wrench lol. But thank you for the good video!

Bro thank you this i couldn't find on my own thanks to you I did

Don't forget to silicone the roof light grommets while you right there. They leak horribly as well.

I have not confirmed but, the information in this presentation seems to be very similar to a 2000 Lexus ES 300. Thank you so much for the EXTREMELY TO THE POINT video. EXCELLENT !!! No jibber jabber. Thank you !!!👍🏽👍🏽👍🏽

INFINITE WISDOM IS RIGHT ON THE SPOT HERE

Thanks for the interesting video. I am struggling with a similar problem.

Thanks for the interesting video. I am struggling with a similar problem.

I have the same problem with my Hummer I was just wondering if the bend. I should say the 90-degree angle you're holding in your head is in the same on the passenger side

how do you compare the ride vs when you had AHC

Awesome.... Thank you. Doing that tomorrow on mine ! 👍👍👍

Not a good thing to put your tools on the battery

HUMMER AASIF LIKED THIS VIDEO💪💪💪❤❤❤

Questions my truck hummer liquid water under sun run explaint to my more please

Would this problem caused service stabilitrack and engine reduce power?

Bonn N N

the infinite wisdom shit kilt me lol great video

So here is an easier tip that worked for me. I poured some degreaser/cleaner in the holes. Let that sit for about an hour and then took my air compressor hose and put the plastic beach ball type inflator tip from a bicycle pump on it. (I just taped it on with electrical tape.). Put it snugly in the hole and pulled the trigger. Cleaned it right out and water flows freely through it now!

I just did this on a 2012 Yukon Denali 6.2l - easy. Fired right up. Seems to run good. What started it all was oil pressure sensor - gauge reading nothing or erratic. Changed that and P0300 code appeared. Ran Techron through two tanks of fuel. No vacuum leaks. Had P0305 code appear for a day which means misfire on cylinder 5. Changed plugs and wires and P0300 code remained and P0305 disappeared. Had a guy tell me a lot of times it's the crankshaft position sensor so I changed it by disconnecting battery and making the repair. Code was not present when I fired it up. Have only driven a mile or so. Will report back when I get some more miles on it. Normally takes less than an hour to throw that P0300 code if it's still present.

Bro thanks for actually knowing how to give sizes, wish all yt mechanics knew how

please help i cant find the connector for the harness i have a 2002 jetta tdi alh but my connector isnt where yours is please help asap!!

I need to get this done. I have a 1998 Acura RL. I Love this car. New spark plugs, tires and a battery. I keep thinking about selling it but it is still a nice daily car.

Do you have to Relearn this sensor? There has been a couple of times the check engine and stability track lights come on. I took it Oreilly and they told me it was the crankshaft sensor. Then on my way home the check engine light turned off. I know I still have to replace it. I just don't know if it the sensor has to be relearned. Thanks

How many inches went up?

I just need to know how do i take the back seat out to even do all that if you know please tag me seriously

Nice video. Had hell finding anything on this. Next is figuring out how to relearn this thing with my scanner lol