10 ай бұрын
Пікірлер
@Illi309 6 сағат бұрын
So this has to be a 4t40e or 4t45e transmission?? Correct?
@eightyfan02 Күн бұрын
enjoy the gas aroma guys !
@Turningwrenches85 4 күн бұрын
Nice work brother
@SomeoneElse-l9b 5 күн бұрын
Hell naw
@whatsnextgarage 5 күн бұрын
@@SomeoneElse-l9b 🤣👍
@djyoryi4609 8 күн бұрын
filter?
@whatsnextgarage 8 күн бұрын
@@djyoryi4609 you have to go to the dealer to get it. I had to. Don’t remember the ford part number…sorry
@Sparaco487 12 күн бұрын
On these govenors is there a return spring that closes the carb butterfly? Mine wide open engine off
@whatsnextgarage 12 күн бұрын
@@Sparaco487 I don’t really remember. I don’t have this machine anymore. Sorry I just can’t remember
@leeexantus5126 15 күн бұрын
Thank you for sharing 😂
@stevied5648 15 күн бұрын
Forgeeeet that!!! My little fusion with slip until it can’t slip no more!!! 😂😂😂
@charleshines2142 15 күн бұрын
I like the rear differential, the hardest part is pumping fluid back into them really. Even the front one is not so bad but you gotta take that plastic off the bottom to get to it. That front one probably needs the changes a lot sooner since it is near the hot exhaust pipe. The one in the rear won't be quite as hot since it is going to be mostly from friction and is used really only until you get to around 25 MPH and the vehicle becomes front wheel drive. I added a bit of Liqui Moly molybdenum disulfide additive for gear oil to both differentials. It comes in a 1.75 ounce tube but is has enough MS02 to treat 2.5 liters of oil according to the instructions so you don't need a lot. Don't worry if you add a bit too much, it is a friction reducer. Just be careful if there are any clutches that could slip an make sure that you can use it without causing damage. I know for my 2017 Nissan Rogue Sport SV it is safe. I even asked questions in the Nissan forums just to see if either differential is limited slip or anything special that needs a specific additive.
@jefong58 17 күн бұрын
Who designed the SUBARU😢
@isubiez 21 күн бұрын
Man I did the same thing had no clue tell the first time I got a ticket and needed it
@davidblum_ 21 күн бұрын
A mechanic is charging me $240 for the labor is that reasonable?
@whatsnextgarage 21 күн бұрын
It depends if they are flushing it and replacing all the oil or just dripping the pan and doing what I did. If it’s a total flush, these days it’s probably close.
@davidblum_ 20 күн бұрын
@ just the transmission oil change so not a flush. He will do what you did in the video. Labor $240 was what he told me his changing the gasket and filter as well
@whatsnextgarage 20 күн бұрын
@ seems a bit steep
@davidblum_ 21 күн бұрын
How many quarts total for the change?
@whatsnextgarage 21 күн бұрын
About 6.5
@adithefox 21 күн бұрын
Thank you much for validating my struggles!!!
@HueyPPLong 22 күн бұрын
Did you use the forestry mulcher on those big stumps?
@whatsnextgarage 22 күн бұрын
@@HueyPPLong the mulcher tried but the oak stumps won.
@mariovivanco190 22 күн бұрын
Does this prevent the truck from sagging when hauling and does the ride quality ? Without hauling anything
@whatsnextgarage 22 күн бұрын
@@mariovivanco190 the bags do not effect the ride when empty and it definitely helps with heavy load sagging.
@nolangietzen4668 24 күн бұрын
All u need to do for that plastic shield is take 4 clips off an use a bunge cord to hold it out of the way
@50tigres79 25 күн бұрын
awesome
@mexicasoldier8364 26 күн бұрын
what is the adhesive for?
@whatsnextgarage 25 күн бұрын
@@mexicasoldier8364 holds the pad against the piston when the brakes are release
@BrandonAmmons-e6g 27 күн бұрын
Good thing you still have a 3/4 impact socket
@whatsnextgarage 27 күн бұрын
@@BrandonAmmons-e6g 👍👍
@johnhouli3450 28 күн бұрын
Thank you. I have same vehicle our noise is like a rubbing spongy sound. What do you suggest
@Terrence12Gardenr 28 күн бұрын
Anybody know what the rubber hose with the yellow tag Is? 1:37
@whatsnextgarage 28 күн бұрын
@@Terrence12Gardenr that’s the flexible line to the top of the fuel tank
@Terrence12Gardenr 28 күн бұрын
@whatsnextgarage mine has a hole in it I'm trying to see if I can just replace that or to I have to replace the whole line
@whatsnextgarage 28 күн бұрын
@Terrence12Gardenr you should be able to replace just that part. Or you could splice in with fuel pressure rated hose and clamps.
@noelnoel4916 29 күн бұрын
My ford fusion hybrid 147000 I have transmission problems any Machanic I need it fix
@alvisguillermo Ай бұрын
thank you !!!!!
@christianc.6064 Ай бұрын
What was the torque for the pulley bolt?please.
@whatsnextgarage Ай бұрын
@@christianc.6064 I went 100ftlbs plus 90 degrees. Not sure what the torque was supposed to be so that’s what I did
@christianc.6064 Ай бұрын
@@whatsnextgarage Thanks a lot!
@XennialGuy Ай бұрын
Just FYI, an alternative OE quality CVT fluid for less than half the price is TRIAX CVT ATF oem grade. It's the same greenish-blue stuff Nissan uses and meets NS-3 specs but runs $45 for a five quart jug on Amazon.
@rocblick Ай бұрын
Part numbers?
@NamelllemaN Ай бұрын
Couldn't find many good maintenance videos out there for the 2016 rogue. Thanks for making this
@whatsnextgarage Ай бұрын
@@NamelllemaN you’re welcome! Thanks for the kind words.
@Slotcartires Ай бұрын
You have a hoist !!!!!! Use it.
@whatsnextgarage Ай бұрын
I know! My brain wasn’t fully functioning🤦
@LandFather Ай бұрын
Ghost ride the wheel horse
@alexanderalex2829 Ай бұрын
Hey how much torque did you use for these bolts when you put on the flywheel to the counterweight?
@whatsnextgarage Ай бұрын
I don’t remember. Let me check what it was and I’ll respond. I’m doing a drywall job today so it’s gonna be a little later.
@alexanderalex2829 Ай бұрын
@ thank you
@whatsnextgarage Ай бұрын
@alexanderalex2829 I did 43 ftlbs but the book says 70ftbls. The pressure plate is 20 ftlbs.
@alexanderalex2829 Ай бұрын
@@whatsnextgarage thank you. This helped me a lot.
@Jesus.Is_King Ай бұрын
So on mines, the temperature gauge is giving me normal temp reading. But when I plug in the obd scanner and run the car it showing me temps of up to 230 degree Fahrenheit. Would that be the thermostat or sensor???
@whatsnextgarage Ай бұрын
@@Jesus.Is_King I would try the sensor first.
@Chilly-uq2zl Ай бұрын
About to attempt this in a few weeks. Ive been looking for leaks for months, replacing one by one. Cleaning everything up. Ive known it was probably this pan but have been swerving it. I dont have a lift so im nervous
@whatsnextgarage Ай бұрын
The hardest part on the ground is going to be the exhaust. I’ve done this same pan 4 times and expected different results. I have something other than the pan at this point. My transmission lines were leaking as well. Good luck!!
@Chilly-uq2zl Ай бұрын
@@whatsnextgarage keep us updated if u find a new leak! We may have the same who knows!!
@shorte785 Ай бұрын
How did you know that the thermostat was the issue with the car?
@whatsnextgarage Ай бұрын
@@shorte785 no consistent heat inside the car.
@garyminer8907 Ай бұрын
I skimmed through your other videos looking for the “update” on this project. Did you ever finish it? Run into problems or concerns? I see this video is 2yrs old and I see you replied to another comment about 1yr ago saying that you were going to double the width. Would love to see how it turned out. My step father is getting up there in age and wants to build an elevated stand. He’s a scraper and has some pallet racking. Told him that would probably be the best way to build a solid long lasting foundation. I really like the idea of concrete tube to anchor off.
@whatsnextgarage Ай бұрын
@@garyminer8907 life got in the way. I have the second set of pallet racking but haven’t gotten back to the project yet. Our idea with the second rack is to build the stairs in between the up rights. So half way up would be in one set, then a platform to rest, then a second set of stairs into the stand. Although we are super busy, that project will get done eventually. The anchors and the structure so far are solid as the day we put it up.
@garyminer8907 Ай бұрын
@@whatsnextgarage Totally understand. Nice idea on the steps. I’ve been keeping an eye out for anyone getting rid of an old warehouse safety steps with wheels removed. All metal, built in railings and most have a square landing at the top. Best of luck.
@luisvazquez5095 Ай бұрын
Mine the control panel, and the numbers dont want to change temperature
@kovie9162 Ай бұрын
How to do this properly: 1 - Disconnect pump wiring connector 2 - Run engine till it bleeds the supply line dry 3 - Disconnect supply line at tank 4 - Cut bad line with pipe cutter or hacksaw--slowly, so as to not risk sparks 5 - Replace bad line with proper line or hose, fittings and procedure 6 - Reconnect line at tank & pump connector 7 - Run engine
@whatsnextgarage Ай бұрын
@@kovie9162 100% correct. I did it like a knucklehead 💪💪🤣
@kovie9162 Ай бұрын
@@whatsnextgarage It takes character to admit and learn from it, though. Ask me how I know. 😆
@whatsnextgarage Ай бұрын
@@kovie9162 have a great weekend!!
@UnknownUser-kx4rk Ай бұрын
I don't see how you got the bolts out between the oil pan and transmission the ones on the side of the pan
@whatsnextgarage Ай бұрын
I used a 3/8” ratchet and a socket. It goes in.
@andrewkilroy323 Ай бұрын
Pinch the brake line...... I hope no one uses this video to help do their brakes.
@whatsnextgarage Ай бұрын
@@andrewkilroy323 still rolling along good. Tons of miles. I got lucky
@ryanl8730 Ай бұрын
So which one was better?
@whatsnextgarage Ай бұрын
The ultra blue is starting to weep a little. The ultra black is the way to go for oils. Blue is water pumps and thermostat housings from what I’ve learned.
@Farhad_ZKD Ай бұрын
@@whatsnextgarage Is Ultra Gray good for engine oil pan?
@whatsnextgarage Ай бұрын
@ ultra gray or ultra black are the way to go. Blue is for water pump, I didn’t know that at the time, it doesn’t leak yet though.
@Farhad_ZKD Ай бұрын
@@whatsnextgarage Thanks!
@brobrohmu736 13 күн бұрын
@@Farhad_ZKDused ultra gray and started to leak after 3 months but idk bc I kinda have a blown head gasket so the gas may have diluted it but I’m kinda in a pickle
@pablopablo6946 2 ай бұрын
Which solution did you wash with? Can it be with water?
@whatsnextgarage 2 ай бұрын
I imagine water and soap then make sure you blow it out good with compressed air.
@twinfin8867 2 ай бұрын
20:03 "Rain Man' impersonation maybe? haha
@whatsnextgarage 2 ай бұрын
Hot hot muffler is hot 🤣🤣🤣👍
@smartinez60 2 ай бұрын
I have the same problem with what seems to be the same fridge. Defrost over night works for about 3 weeks. I wonder if there is something that unthaws the ice that is no longer working.
@flpnnino 2 ай бұрын
Great video! Thanks for sharing! Do you happen to have a video of hardwiring it to the fuse box?
@whatsnextgarage 2 ай бұрын
Thanks for the kind words. I do not have a direct fuse box wiring.
@LOLONO666 2 ай бұрын
can we remove this pipe without removing the bumper
@whatsnextgarage 2 ай бұрын
I guess I don’t know. Sorry.
@charleshines5700 2 ай бұрын
What are the signs of bad subframe bushings? I hear clunks often when I go over a bump. My steering feels loose. Nissan dealer says he could not find anything wrong. I am wondering if he ever checked those subframe bushings. At night it is kinda scary because if you are turning and someone is coming up and partially blinding you that can make it hard to avoid hitting a curb with it feeling imprecise like this. They don't know it but in those situations I am thinking, oh great, please just go already and allow me to make this turn in peace!
@whatsnextgarage 2 ай бұрын
@@charleshines5700 the cluncking is part of the issue when these bushing go. If you took it to a Nissan dealer they should have checked those with the initial complaint of a cluncking noise over bumps.
@charleshines5700 2 ай бұрын
@@whatsnextgarage I have an inspection scheduled. I told them that I found this and asked them to look into it while the vehicle is inspected since it most definitely is a safety issue of varying magnitudes depending on the road conditions and all other variables. I even tell them too that as long as it continues to do this I pray that the CVT goes out and I have an excuse to get a better vehicle. I was a Volkswagen owner and I liked it a lot. They have tight steering and that is how it should be. My 2017 is a Rogue Sport (Quasqai over seas) and I expect better. Something just seems amiss with the handling and it was not always like that.
@whatsnextgarage 2 ай бұрын
@charleshines5700 don’t let up the pressure on them. Sometimes they can be complacent when the issue isn’t obvious. Most are good but there’s always a few that don’t take their job that serious.
@bigd835 2 ай бұрын
looks very likely to damage something or crack the piece holding the bearing. too much
@whatsnextgarage 2 ай бұрын
Broke the wheel speed sensor🤦💰💰
@tatking873 2 ай бұрын
Man I died laughing it’s not funny but damn 😂😂😂 car is a nightmare
@Hombrewrx 2 ай бұрын
The only easy solution without force or welding! kzbin.info/www/bejne/hZW4kmCQeZarrrcsi=-gx6u8lKXZPwnDGh
@richardsoule278 2 ай бұрын
Very good, thanks.