could removing the value cover make it any easier to reach since it gives you that extra few inches
@brett.3223 күн бұрын
I think that would be too much work just to pull the sensor you just have to go off feel I had to do it a second time and did it in less then 30 minutes. Follow the wire to help find the bolt
@WorldWideMediaGroup123 күн бұрын
@@brett.32 cause i have 5.0 are hands are to fat or arms thats why im was asking
@brett.3223 күн бұрын
I mean yeah if you can’t reach down enough then I guess you don’t have much of a choice but I would just make sure that it will free up enough space so you don’t take it apart and still have the same issue
@WorldWideMediaGroup121 күн бұрын
@@brett.32 I could so I did a lot easier taken me less then 10 mins to remove the sensor extra 25 to put value cover back on I know I had to use with an 8 mm socket wrench
@brett.3220 күн бұрын
Great job glad you were able to get it done
@vegasfordguy29 күн бұрын
There's no reason to start the engine while doing this. Do it cold with the engine off so you don't burn your hand. This product works 100 percent, however you could also drain and fill the transmission and almost always have the same results.
@brett.3229 күн бұрын
I tried doing it cold the first time and it wouldn’t take the fluid tried again with the engine running and took it no problem.
@daddyspage931Ай бұрын
Thank you that’s awesome information
@MikeM-cz5lnАй бұрын
Since the module is faulty (and you need to buy a new one) maybe you cannibalize it and place the jumpers on the mating connector. That way it would be a simple matter to plug in and unplug your bypass.
@brett.32Ай бұрын
My module wasn’t faulty I just made this video because I was already back there. There are forums out there where people made permanent jumper connectors if that’s what you’re talking about?
@jerseyteacirАй бұрын
Is the shutter problem same symptoms of the common driveshaft issue? A highway speed about 65 miles I feel the vibration. Not sure if it's the drive shaft or the shutter. If I don't go to 65 the truck drives smooth.
@brett.32Ай бұрын
It could be the shutter because on my truck it would only do it at highway speeds. I would definitely start there because that’s the easiest and cheapest thing to try instead of messing with the driveshaft
@JoseMartinez-g2dАй бұрын
Thank you sir, this worked in my 17 f150 ecoboost, had been doing the shudder for about 5 months, thanks to you is now fixed.
@Rob_S197Ай бұрын
Hey man just recently did this on mine bc I was having the same problem but just 1 day later after install , hitting some bumps the sound came back again on my left side . What else do u think it could be bc no way the links , bushings went bad in just 1 day after hitting bumps
@brett.32Ай бұрын
No clue man I’m not a certified mechanic by any means
@2fast4traction89Ай бұрын
Try replacing your shock absorber
@Superior-ConceptАй бұрын
My guy !!! Appreciate this doing it my 07 f150 today hopefully it works
@lilced954pimp29 күн бұрын
Did it work?
@6.7johnny782 ай бұрын
Off topic but do you have any pictures of this truck anywhere? I want to put those wheels on mine.
@brett.322 ай бұрын
No I sold the truck awhile ago but they were the wheels off the 2018 f150 roush I’m pretty sure. They’re hard to find though since the only way you could get them is from buying a roush f150.
@6.7johnny782 ай бұрын
@@brett.32 I got ya, I appreciate it. Yeah, I’ve been looking for a set for a few months now.
@brett.322 ай бұрын
Yeah I found mine on marketplace for $625 without tires
@Contenders772 ай бұрын
There’s no way that goes into the torque converter. Torque converter sits between engine and tranny. Only way u get fluid in torque converter is separate transmission from engine and remove converter. The fluid in there never gets changed even after a tranny flush.
@lanetv3513 ай бұрын
Did you happen to also get a flashing check engine light that would go away after maybe a min or so? Mine read misfire so replaced plug and coil but same issue happens. So just curious if you or anyone else did the same but shudder fix helped. Thank you!
@brett.323 ай бұрын
No I never got a check engine light
@jshinobu0072 ай бұрын
Mine does the same. Same year 2015. Did you figure out the issue?
@angrygnome43042 ай бұрын
@jshinobu007 2015 here too going to have to try this mine just started having this issue
@sammydunham47692 ай бұрын
If it is having a miss fire and your plugs and coils packs are fine drill a small hole bottoms driver side of your intercooler
@Buttkicker132 ай бұрын
Mine is doing the same thing just wondering if you got yours fixed
Thank you sir! Unfortunately, the bar bushing in currently unavailable, but I found the same one on eBay.
@cjgambill4 ай бұрын
thank you!
@MustangGuy19964 ай бұрын
Should you grease the new end link bushings as well before installing or just grease the bigger rubber bushings on the outsides ?
@brett.324 ай бұрын
I don’t see why you wouldn’t be able to so I say go for it. The ones that I bought said they were already greased and that I didn’t have to do anything to them so I went with it. I haven’t had any problems with them since and it’s been 6 months.
@creightonwee70474 ай бұрын
Was your engine idling funky when this code appeared and did this sensor resolve the issue
@brett.324 ай бұрын
My engine idled a little rough but it ended up being my timing chain that needed to be replaced the guy at ford told me that it’s rare for those sensors to fail so you might want to check your timing chain
@highndri13844 ай бұрын
for me, I removed the air cleaner bracket and the coolant hose and I could get easily access. It's also an 8 mm socket for those who may be doing it. Thanks for the video.
@brett.324 ай бұрын
Thank you I just added the 8mm to the description I thought that’s what it was but it had been so long since I had done it I didn’t want to put the wrong size
@starwest10004 ай бұрын
Where can i get that
@brett.324 ай бұрын
I bought it at AutoZone
@starwest10004 ай бұрын
Where can I got that
@tommyriley25922 ай бұрын
Autozone
@Joe-fi2ir25 күн бұрын
My local Autozone has it.
@RonnieYoung-zx8wu4 ай бұрын
Take the inner wheel well out it's a lot easier than you can get right in there
@brett.324 ай бұрын
I’m sure that helped out a lot I didn’t want to mess with it tho😂
@conor34 ай бұрын
Thank you bro.
@UglyKidz3575 ай бұрын
I believe I have the same issue your explaining and I’ve done some research and I also believe it’s the torque converter. Sounds like a shutter/ rumbling / somethings is rubbing sound … sometimes it’s when accelerating from 3-4 gear and then just coasting .. but anyways what I’m wondering is since I am also going to do a transmission oil service should I add this after I drop the oil or after I add the new transmission fluid?
@brett.325 ай бұрын
I would say after so it stays in there longer. I also heard that sometimes the problem is fixed with just a fluid change and nothing else. The old dirty fluid could be part of the reason it’s slipping.
@MJ-iy4fb5 ай бұрын
Outstanding man!! Thanks for the video, I will try it on my 2007 F150.
@arcticbuilders58655 ай бұрын
Did it work?
@dancrumbo59222 ай бұрын
@MJ did it work???
@MJ-iy4fb2 ай бұрын
@@dancrumbo5922 Kind of. It helped but did not cure the whole problem.
@MJ-iy4fb2 ай бұрын
@@arcticbuilders5865 It helped but did not cure the whole problem.
@AlexTorres-tu9zs6 ай бұрын
Bro, seriously, you should not be making videos with your explanations. No help what so ever.
@brett.326 ай бұрын
You know what’s so great about KZbin you don’t have to watch my videos if you don’t want to
@taylorcarson92136 ай бұрын
You think a bad phaser will throw code
@brett.326 ай бұрын
Not sure but I know a bad timing chain will
@TooMuchFandango566 ай бұрын
Why couldn’t you just squeeze it into where you put the transmission fluid?
@CFlo932 ай бұрын
On these particular model transmission that is where you check and service the fluid. It cannot be done from underneath the hood or engine bay area. Hope that makes sense.
@rigakit6 ай бұрын
So adding the red goop to a fairly new truck fixed the problem?
@brett.326 ай бұрын
Yes but I wouldn’t say new it had 190k miles
@Ghost5.46 ай бұрын
Why does it need to be running?
@brett.326 ай бұрын
If it’s not running the fluid won’t go into the transmission
@RickActualАй бұрын
I was about to ask this too.
@vegasfordguy29 күн бұрын
The fluid will absolutely go into the transmission with it not running unless you filled your transmission too full.
@erichigginbotham6277 ай бұрын
This worked for my '15 FX4 EB with 140k. I added the Shudder Fix and let sit about 30 min and drove about 60 miles and haven't felt it since.
@JustinThomas-vk5px3 күн бұрын
I hope this helps me if not no hunting this year for me
@thehappyhooker51467 ай бұрын
I hate that ford did this
@nolanduarte7 ай бұрын
Whatever getting under your truck while it is on is awesome
@drz400sm52 ай бұрын
Gives you an opportunity to watch your plastic oil pan leak,again.
@MrObrently8 ай бұрын
Thanks a bunch buddy! The newer ones are on the top. That picture helped a ton! I think I got it done in about an hour. No room back there. I was able to push one of the hoses out of the way to get a little more room. I put a blanket over the engine and laid on top of it to work on this. 👍🏻
@223Judah8 ай бұрын
Before you fixed it did it make noise when you go over stuff?
@brett.328 ай бұрын
Yes you could hear a clunk over speed bumps or bad roads
@223Judah8 ай бұрын
@@brett.32 I think this is my problem I thought it was my motor mounts. How much is it to get fixed?
@brett.328 ай бұрын
I ordered all the parts I showed in the video for $30 on Amazon
@DunnMotors8 ай бұрын
Great! Video and explanation with those pictures. THANK YOU! AND IT WAS LESS THAN 5 MIN
@edlopz17228 ай бұрын
Thanks for sharing this.
@achkamoo36959 ай бұрын
Have you changed the spark plugs?
@brett.329 ай бұрын
Yes I did. It was a transmission problem not something with the engine.
@erichigginbotham6277 ай бұрын
That is a good question. Ford engine miss will mimic converter shudder in older trucks and if left missing it will kill the transmission but the 6r80 it is commonly a shudder. This fixed mine until I can replace filter and refill. I lifted the passenger side, cold and not running. I added the Shudder Fix and let sit about 30 min and drove about 60 miles and haven't felt it since.
@Ghost5.46 ай бұрын
@@brett.32what was the issue with the transmission?
@richarddeanandresen9 ай бұрын
I’m ready to do this now. Two questions; what size socket and is there a difference between the parts for bank one or two? Auto one didn’t give me a choice. Thanks for the vid!!!
@PeteUehlin9 ай бұрын
Yup I did!
@PeteUehlin9 ай бұрын
I’m tempted to trade it in and get a new truck but I’m sure I won’t get anything for it and the new tundras are over 50 K plus you can only get them with V6 turbo so they might not be as reliable as the old V8 as well
@jasonirwin60259 ай бұрын
Thanks! That photo of the back of the engine made all the difference.
@didieraubry99219 ай бұрын
Incroyable même pas en français
@leftnutt609510 ай бұрын
But did you do the other sensor too i think you did bank A what about bank B
@wyatts_dad10 ай бұрын
Thank you ! Perfect description of how to do the job. VERY tight space. Used a mirror to ID the bolt then it was all based off of feel and the description of your video.
@bearing_aficionado11 ай бұрын
People just because you get that code, it does not always mean your sensor is bad. I had that code and it was my timing chain that was stretched causing the code to trigger. Yes I got it fixed. Had to replace my timing chain, guides, two of my cam phasers, and had the internal part of the water pump replaced (because they were already in there it was preventive maintenance). Cost me around $3500.
@brett.3211 ай бұрын
I only replaced my timing chain for $1700 at the dealership everything has been great zero issues
@bearing_aficionado11 ай бұрын
@brett.peacock damn that's cheap! I took it to an independent shop because they could get it in right away. The dealership had it for a week and still did not look at it. Regardless, it was still the around the same price.
@brett.3211 ай бұрын
@@bearing_aficionadotypical dealership wait times
@bearing_aficionado11 ай бұрын
@brett.peacock one guy was working on an engine and another a transmission. I do know the dealership was going to remove my cab to do it because its easier that way. The other shop had a young guy who was like 6ft. 4in work on mine. He took the whole front of my truck apart to do it.
@PeteUehlin9 ай бұрын
So did the code come back after you installed the new sensor and then you replaced the timing chain?
@1957PastorPaul11 ай бұрын
It was a bear, but I got it done... thank this was the most helpful of the videos
@flossie71311 ай бұрын
Honestly, by far the best video on this issue
@AndrewMoizer Жыл бұрын
Brett, thanks so much for putting this together. There seemed to be quite a lack of information about 3.5l V6 Cam sensors until I found this, which clearly shows which sensors are which. I'm working on an Edge, I managed to get the Bank 1, Sensor B out using a long handle flex ratchet and medium extension. Unfortunately the CT parts guy had looked up a crank, not CAM position sensor so I'll have to wait for the right part before I can see if I can get it all back together. I only had to take off the air box leading to the throttle body to get access to the sensors on bank 1 (closest tot he firewall on a FWD vehicle). Many thanks again.
@AndrewMoizer Жыл бұрын
Got the new sensor installed and all seems to be working fine. Took a combination of flexible retrieval magnet, extra long pliers, various extension combinations, hand contortions, and more to get the new sensor in place and tightened down! But didn't take too long overall. Thanks again for taking the time Brett.
@jackarchdekin85489 ай бұрын
@@AndrewMoizerdo you know what size of socket I’ll need for the bolt ?
@AndrewMoizer9 ай бұрын
@@jackarchdekin8548 sorry, I don't recall off the top of my head. Maybe 10mm. It was relatively small, used a ¼" socket drive.
@boostercontrol100 Жыл бұрын
Thanks man!! There is literally nothing else out there for our 2011 that shows like this. Great job 👍
@youngphilly8977 Жыл бұрын
You’re an amazing person
@AndrewTashbar Жыл бұрын
Did yours have slow acceleration?
@SirGunsnstuff Жыл бұрын
Your video saved me so much time! Literally took me 20ish minutes
@brett.32 Жыл бұрын
Yes I had to mess with it a second time and was able to do it in under 30 minutes