thanks for the tutorial 🎉..Wel how can I adjust the angle of the fan? I want to increase
@Kelv_Nganga10 күн бұрын
wonderful! 🎉
@irwinjimenez11 күн бұрын
Why wear gloves when it's all de-energized? 👎
@kalutecpowersolutions952310 күн бұрын
Technically, just understand they are pinch points.hence, safety first.
@krizt.jeremiah405012 күн бұрын
Hi, I am an student of electronics and will need a help in building a system where a CIU can be monitored by a means of a GPS tracking device. This device can also cut off or switch on the CIU in case of an attempt to bypass the token recharge process. Using a simple input and output devices, your contribution will greatly be appreciated.
@krizt.jeremiah405012 күн бұрын
Can A Remote power control device be placed at MCB1 to monitor and control the CIU?
@abdalwasaalsaidi12 күн бұрын
Wrong inviter contact to the controller charge
@salmansamol26316 күн бұрын
bhai ye video banane ke liye aapne konsa softwer use kia he agar aap bata pao to aapki meharbani
@chrismagor50616 күн бұрын
hello can i use this to run 12dc leds and do you have a components list i want to power an actual set of 1960s traffic lights for a man cave cheers chris
@rainfordmiller304617 күн бұрын
Please make a note what is data and what is 24 volts please used other devices that used 24 volts with a different pen so we can understand the difference between data and 24 volts all the video i have seen its just data wiring tanks alot
@fidelcarlos952619 күн бұрын
where is the supply of timer
@sergeipshenichnikov671822 күн бұрын
Ролик, блять, для, дебилов. Но дебилы не используют сигнализации. Просто украли 2 минуты моей жизни.
@grahamjohnbarr27 күн бұрын
am using this setup. My problem is that one controller is working the other doesn't when both Panels are connected. one 300W P & one 300W M. If I switch off one Panel, 300WP, the Charge Controller on that side works. If I switch that one off & the other, 300WM, on then that Controller works, but they won't work while connected together in that configuration. Why? any ideas? Both 40A EPEVER CC's. That feed into a 300W LiPo4 Battery then into a 8000/4000W Inverter.
@HasanSikder-e3rАй бұрын
wrong
@Psalmist.SamuelAdamsАй бұрын
Turn the music down
@gabindade2102Ай бұрын
Thanks for the advancements, keep it up
@glenn49111Ай бұрын
This is really really bad. The video shows the connections but DOES NOT SHOW TERMINALS. If you don't show what terminals you are connecting to i.e 85, 86 etc then whoever follows this will likely blow up what they are wiring. A good video made useless by 1 mistake
@Laser17thАй бұрын
very profectional engineer
@KaluyaInnocent-j3hАй бұрын
🎉🎉🎉❤❤ i love it
@AsifNiaz-wu4egАй бұрын
Very nice❤❤❤❤
@AsifNiaz-wu4egАй бұрын
Very nice❤sir
@FransiskoFransisko-m7eАй бұрын
Makasih Bang Ilmunya
@marcocruz263Ай бұрын
Led esta ligado errado!!!!
@BrioptionalАй бұрын
make no sense, 2 me
@hafizzomar9287Ай бұрын
Good work 👏
@kalutecpowersolutions9523Ай бұрын
Thanks ✌️
@RgCupangАй бұрын
draw the design using what application?
@mdashab5580Ай бұрын
Nice digaram
@joelcanales26002 ай бұрын
Thnks for the videos im so satisfied to watch your tutorial sir...👍
@kalutecpowersolutions9523Ай бұрын
So nice of you
@joelcanales26002 ай бұрын
sir ,its very clear and easy t o understand👍👍👍
@thefrdz-sc9jl2 ай бұрын
Is loop isolator same as control module?
@KeyPlusTools2 ай бұрын
Diagram please
@aboahmedhaddad46852 ай бұрын
👍👍👍
@akmedianewstaml76722 ай бұрын
Super
@ohobbista41842 ай бұрын
Simplesmente não vai funcionar! Circuito está adulterado 😮
@ohobbista41842 ай бұрын
O source não é ligado ao negativo? Dreno e source são positivos, sou leigo bo assunto, poderia explicar melhor?
@d.master.pp.master.d72012 ай бұрын
I try this setup and i used different controller and different variant of panels .. my solar setup loke this is.good.proper wire sizing and DC breaker
@kalutecpowersolutions95232 ай бұрын
Thanks for sharing
@nasimalam-ll5yx2 ай бұрын
L और N मतलब?
@princeukomatthew55442 ай бұрын
Insightful and educative, but how do one take his load point from.?
@raypilgrim69052 ай бұрын
Just the video I've been look In for to do a wiring job in my basement thanks👍
@kalutecpowersolutions95232 ай бұрын
Glad I could help
@usrm-wm1osbr5v2 ай бұрын
The indicator's one end with resistor is correct, but the other end should be conneted to the opposite end of Thermostat. Then only it will glow only when thermostat is ON.
@mahdifourati61922 ай бұрын
wrong schematic because the drain is connected to +12v which mean we have a n channel mosfet so the configuration must be low switch which mean that the load must be connected to +12v (serial with drain) and not to 0 v.
@MarkReyes-u1y2 ай бұрын
dc or ac
@monirelectronicsplumbing7202 ай бұрын
Bro, what software do you use to edit this kind of video, please give me the link of that software, I also want to edit it, bro.
@monirelectronicsplumbing7202 ай бұрын
Bro, what software do you use to edit this kind of video, please give me the link of that software, I also want to edit it, bro.