scirockalot8v

Пікірлер

@neilowens1504 6 сағат бұрын

That zip tie trick was spot on, man! Thanks!

@johntomasik1555 6 күн бұрын

Good vid, but wanted to draw attention to @jimwilliams3494 post below about not needing to undo the13mm carrier slider pin bolts.

@Anonymous-dd2ju 18 күн бұрын

Did only I hear the disaster alarm 🚨 🌪️???

@jaxforrest2189 27 күн бұрын

How do we get there

@scirockalot8v 27 күн бұрын

@@jaxforrest2189 Martys Island. Have to boat there.

@hiya1234567899 Ай бұрын

Love the music playing!!! 🤘🏻

@AnotherCG Ай бұрын

Great demonstration. I have read what i believe is every manual for the blheli series. All confusing. I program using an esp32 board instead of a transmitter or app. Your video clearly does what none of the manuals do. Thanks!

@Bluejeanmusic1984 Ай бұрын

Thanks so much! Just done this on our 2024 seat tarraco and it wasnt much different 👍 being useless at mechanics this video was a god send. Didnt glue it back in so hoping it doesnt rattle 😅

@DJCARLITOSHN Ай бұрын

Thank you so much dude!

@coltondery3526 2 ай бұрын

I’ve never felt more dumb

@JaxScoBlu 2 ай бұрын

This is actually helpful

@ChadVanryn 2 ай бұрын

Wow

@IllusiveChristie 2 ай бұрын

Magnet

@drsnowmon 2 ай бұрын

Or get a magnetic spark plug socket

@williamjones8690 2 ай бұрын

That's a coil not a coil pack homie.

@minamihasaki4325 2 ай бұрын

Someone doesn't know what they're talking about...

@snafu_vfx 2 ай бұрын

Coil, coil on plug, coil pack…. Come on now my man it’s just semantics we all know exactly what he meant in this context

@bulldogg117 2 ай бұрын

Igntion coil.

@bulldogg117 2 ай бұрын

@snafu_vfx8662 great way to order the wrong part. Theyre named differently for reasons cheif.

@snafu_vfx 2 ай бұрын

@@bulldogg117 hmm fair point, can’t list the amount of times different terminology ends up getting the wrong part. Granted, I work on diesels after leaving the automotive side so fair play I imagine you guys know far more than I on the spark plug side Edit: on my end I’m used to ordering parts under a VIN, so less issues with ordering a part that isn’t even optioned on the vehicle

@matthewnorris203 2 ай бұрын

Yes. Good reminder

@ryansavage3675 2 ай бұрын

I know this is an old video, but thanks for keeping it up. Going to be a big help for me in a few days. LoL Much ❤

@mokdadus 2 ай бұрын

Very good 👍

@e1085 2 ай бұрын

Also that wasn’t the highest point of the island correct?

@scirockalot8v 2 ай бұрын

Nope. There is a ledge thats is maybe 6 to 10 ft higher, but more of a jump out and I wasn't comfortable with that.

@e1085 2 ай бұрын

Nervous fart there?

@scirockalot8v 2 ай бұрын

I dont fart

@cbaldan 2 ай бұрын

It's 2024 and I also used Pennzoil Syncromesh in a 2020 GTI. It's perfect! Cheap, and made shifting silky smooth, it was crunchy before! Even on a cold start in the morning, shifting is great. I also took the opportunity to do a shifter adjustment altogether!

@buknar456 3 ай бұрын

what a nightmare. I thought you could fix this issue with tweezers....fak.

@adctd2gtr 3 ай бұрын

Great video, I'm no mechanic but I followed your steps and had no issues whatsoever. You saved me a stack of dough, man, thank you! When I powered on the car afterward though, I do have a couple dash lights showing - the power steering and the skid-correction lights and I'm not sure if the car just needs to run for a while and cycle them out, or what. Any suggestions would be greatly appreciated. Thanks very much!

@scirockalot8v 3 ай бұрын

Usually just driving a couple feet will turn the lights off. Unless you have MAF sensor and it was not plugged back in.

@Shuv455 3 ай бұрын

So how do I do this with one hand if my golf is too low?

@ianmoberg374 3 ай бұрын

How did that fluid work?

@scirockalot8v 3 ай бұрын

Worked fine. Never had an issue. Sold the car with over 100k on it.

@junktime6076 4 ай бұрын

So glad there’s not a 1000 pops and cracks

@scirockalot8v 4 ай бұрын

That wasn't a thing back in the day. Haha.

@laylodau 4 ай бұрын

#lifesaver.. was about to burn $125 for this part from VW. Kids will be kids... Suspect this is the first time but won't be the last🙂‍↕️

@herculesmoto 4 ай бұрын

Thank you for the tutorial! 🤝🏼

@lmd6204 5 ай бұрын

Is there anything different replacing your brakes if you have manual trans with hill descent control??? Thanks!! Great video!!!

@scirockalot8v 5 ай бұрын

I dont believe so. Only difference is if you have an electronic E-brake.

@casinocobi 5 ай бұрын

Life saver

@jimwilliams3494 5 ай бұрын

Since you were replacing the rotor, you don’t need to take out the 13 mm bolts holding the sliders. Save some time and just remove the 21 mm bolts and pull the whole carrier and caliper out at the same time. Once you got the whole assembly off the rotor, the carrier and pins will just slide right out of the caliper for cleaning. The 13 mm bolts only have to be removed if you’re pulling the caliper without disturbing the carrier and rotor.

@johntomasik1555 6 күн бұрын

Yup. Works fine that way. Had the opportunity to add grease to the slider pins since they were exposed doing it this way. Cuts down on pad replacement time, too. And, ya can still get at all of the surfaces needing cleaning/brake lube.

@soaringkhaled 5 ай бұрын

Thanks a lot ..... but take care if you choose bidirectional, it may be impossible to enter programming mode again or factory reset the ESC... .. I really appreciate it if some one explains to me if this is doable ...

@ericwillis777 5 ай бұрын

I see so many problems with these BL Heli ESC's better to ditch them, at least for fixed wing, and go with something cheaper and less complicated. I'm sorry I bought several. Trying to install one now, but every time I move a control surface it plays a tune and then two long beeps. Life is too short to spend time on this.

@raymondphan3806 5 ай бұрын

Great job .. . .. :)

@frankarvia634 6 ай бұрын

I just brought my Beetle in to get the fuel filter replaced and they broke the strap that holds it tight now it’s just kinda hanging there. I told them how the lines come off and to be careful not to break them. I brought the oem filter and asked if they could replace because I didn’t want to get gas all over me. It was weird at the end of the job he explained they couldn’t warranty their work cause I brought the filter. Now I know why

@dasauto44 6 ай бұрын

how many miles did it have before the change>?

@mohammedshafiq1462 7 ай бұрын

Well done 👍

@chillpwn1 7 ай бұрын

Very helpful, thank you. Working on my 2010 Rabbit

@supremegaud7 7 ай бұрын

Out here in southern Cali the dealership wanted $580 + tax to change the plugs 😵😆

@adctd2gtr 3 ай бұрын

GTFOH some of these shops charge crazy shit. The last one I was at called me and said they were literally holding my plugs to check them and wanted $400 to put fresh ones in. Like dude, you've already done the work, just finish it at this point. Nope. So here we are on youtube, learning shit and saving hundreds.

@stevej6758 7 ай бұрын

Great video, to the point without a bunch of fluff, step by step explanations and not too vain to edit out turning the bolt the wrong way. God camera angles and distance to make viewing easy and understandable. I like your use of both anti-sieze & brake caliper lube on the assembly as well. Checked this out as I'm about to do same on my daughter's car.......far cry from my old 65 Impala!

@scirockalot8v 7 ай бұрын

I'd rather work on the impala!

@xsnpxhoff8071 7 ай бұрын

3 cars in the family have same issue yeah vw thanks twat company

@sHpAaKu316 8 ай бұрын

you bought a loads of goods for many $$ but cheaped for pair of gloves? Secondly don't ever smear the hub under the rotors - it causes micro wobles of the disc. It is never meant to be disassembled once a week so put it clean surface to clean surface - that's it! Why haven't you clean the rotors before use with brake cleaner? Greasy discs don't run well. Props for suspending the caliper and overall good approach.

@r.lawless8316 8 ай бұрын

QUICK TIP: i found that using a pick is easiest to push down the clip button to release one of the clips... saves me 30 min of headache...

@rrly4459 9 ай бұрын

Thank you!!!

@CincinnatiNS 9 ай бұрын

great video - thank you !

@ray-hv9is 10 ай бұрын

Thank you for clearly showing how to clip the fuel lines I watched a couple of other videos and they literally just cry the lines off of the fuel filter with a pry bar. Yikes. Thanks again.

@MLeung-vl7we 10 ай бұрын

Got to do this on my MK7 shortly with 72k. Instead of guessing, with a marker, mark a slash on the bolt, and then another 180 degrees on the wheel. That way you can reset the breaker bar to its max leverage point without thinking about the position of the handle. Thought you might have stripped that last triple square. I always clean it and tap in the bit so its fully seated. Turning the steering wheel to the right for more access was a good idea.

@rogergriffiths207 10 ай бұрын

Top marks clear and concise easy to swap it over ! M,ant thanks indeed.

@ChrisLee-yx2yy 10 ай бұрын

Does this video help me with a 2002 vw Jetta GLS 1.8 L

@scirockalot8v 10 ай бұрын

Yes

@Diabolik3 10 ай бұрын

Could mechanic ripp you off with throttle body replacement if only spark plugs were bad? 5 days ago I paid $600 for the throttle replacement and today long start and bad spark plugs. Please, thank you.

Ең жақсы KZbin

Пікірлер