I never used an oxygen torch. There are tons of vids about similar ones. I would use it fotr a while, and make a vid about what I learned lol Thanx Biskit

Did it have all 4 lift pins and the tool wrench for the chuck ? Mine did not but got on the phone and they sent them .. I also ordered a 5 inch chuck for it ...

too bad this only works on certain cars - my toyota doesnt have that hole unfortunately

What was the big plug on the left side fender? I'm looking at one, same color, year, model that has mounting holes in the same spot with an outline that looks the same. Unit is for sale in Talledaga Al.

FFS get to the point.

The poor dog was doing its best to tell you there was no flashback arrestors 😂

Yo doubt you till use it but i just found one on theres in my dads shed but the screens not working any ideas ? It lights up but there the text on it

It will run rough with this board without the choke.

Not suppose too

have to open seat on bomardier 500 when its stuck hope you can help

If you have a Digital Multi-meter set it for measuring 10 Amps to start off to be on the safe side and if they measure less than 200 milli-amps then you can use the the regular setting for 200 milli-amp of current. Then you can figure out the actual wattage of your lights - Voltage x Amperage gives you your wattage.

They claim the Eagle Eye Lights are 9 Watts but mine only use about 100milliamps of current so 12 volts x .100 = 1.2 Watts not 9 watt - 9 Watts divided by 12 volts =.750 or 750 milliamps.

Thanks for your tip! Do you know if spray painting car outside in morning on 101 degree day is to hot if i do it early morning before it gets real hot? I have a car port over and tarp im putting under plus ill be wetting the dirt in the area.

I bought a OTC 6496 to pull my 2003 f150 pitman arm. The tool did not fit. I paid $100 for this tool. What a waist of money. Using a die grinder with 1/8 cutting wheel and a air hammer with chisels is the tool that worked.

2024 and did you ever find the reason? I have a hair dryer with the same issue, blown / melted "commutator," to me looks like high voltage e.g. the 110v , is getting to the motor. It should have been dropped by some sort of resistance/ reduction. This I believe is done by running the supply through one of coils. Then the reduced voltage is rectified by the diode network on the pcb to provide dc 12v to the motor. Just saying ,😊

Great idea! I'm about to save some money... Thanks!

Good idea.

Can you add a digital readout when you buy the product

Isn't that flywheel on there with left hand threads?

Thats MC60 board you have in this video

I'm going to do this to my z750s, its not clear what you did with the cat? Did you remove it? If so how?

I found the density of the Bondo filler and it is 1.14. grams per ml. The density of the hardener is 1.2 grams per ml. I got these from the 3M safety data sheets. So one fluid oz of filler is 29.57 ml and that is 33.71 grams. If you use 1.5% ratio then the hardener amount is .5 grams or .6 ml hardener. If you use the 2.5% ratio then you use .84 grams of hardener of about 1 ml. So this large can of 3.18 kg has a bottle of 78 grams of hardener. 3.18 kg is 3.625 litres and 78 grams of hardener is 93.6 ml . The volume ratio for the whole can is 93.6/3625 = 2.58 . So the % in the tube is 2.58. Many places say to use less 1.5 %. So this gives a ball park range in ml. and now you know how much ml is a 3 inch strip. To calculate that from the can directions. A 3 inch circle 1/2 inch thick is 115.82 ml or about 4 fluid oz. 115.82 ml filler is 132. grams and 2.58% of that is 3.406 grams of hardener. 3.4 grams of hardener is 3.4 /1.2 = 2.83 ml. The can could have just told you this. 2.83 ml hardener for the 3 inch circle that is 1/2 inch thick. So that is the starting point and you could use less hardener and find out how long the working time is, down to 1% or so. I have a lot of these little pneumatic push tubes that I can fill and measure exactly. Get them for ink cartridge refiling etc. I am going to try a 1% mixture and see how many minutes work time and completely harden time I get. Some places say you use more hardener in cold weather and that the filler get hard due to heat produced in the mix.

The board is called MC 60.

You are a true IDIOT, don:t know crap about the Ithaca 49. And your making videos. Just another garage want to be gunsmith.

Exactly the video review I am looking for. Thank you. Unfortunately they are not the ones I need for my car. Thanks again..

Please do ground the motor, it is important. A 200k potentiometer is what you need, as most of those motors are 90V

hell yeah

WOW!!! Just saved me a bunch of money... Thank You your a genius..

Does anyone think this 2hp Smith&Jones motor on 115v can run the harbor freight 3hp compressor pump?

Iv got a machine just like that called a Kronos.

Great video. .. . .thanks! I'm thinking about buying this motor and wondered if my limited electrical skills would be able to handle it. I think I can do it now that I've seen your video. Thanks again.

Hi I'm Ed Super important question please I have a standup scooter it's old scooter I have the exact motor & board took off treadmill would it be possible I can attach the motor with ext. To my scooter and all I need is batteries car battery or two to have same voltage as you plug into wall electrical socket how many batteries I mite need

I have that same machine. Mine is called a Kronos. Is a good light duty machine.

Well all I have to say is this the easiest and best explained how to hook up a treadmill motor and Buddy if you get this message I would like to know what kind of board that is and the number off of it if you could help me out please I'd really appreciate you thank you sir

Beautiful

And i was doubting this stuff wasnt going to work... Made the right choice thanks...

great idea

This guys very annoying

What if you have something with a switch and needed both cc and ccw? I needed to be able to change directions with said switch

"There's just a little tip" What I say to my girlfriend every time. Yes it's equally misshapen in other ways also... It's like a curly Q except it makes a distinctive hard left midway, so much so it looks painful. It definitely has an odd orange color and smells like old fumky cheese. We are talking about Cheetos? Right?

En français svp😢

Thanks for the information

This guy knows nothing about machining by the looks of it

i wish i know that when i was doing this in my hhr lol

Just noticed you have so many 'tips & tricks' in your videos! Thanks man. Keep mentioning in the end that you'll keep supplying them so people catch on to the fact that you keep the channel loaded with the pieces of value. Thank you.

Thank you for that great idea

car wash bay

Dude! Thanks so much. This video was EXACTLY what I needed. Just bought mine

Maybe raise the rear a few cms or call grizzly

Uh, oh, that could have been bad!